How to use Outdoor Sleeping bags

1. Warm up before bedtime

The human body is the source of the calories of Sleeping bags. For example, if you make a small section of warm -up or drink a cup of hot drink before going to bed, it will increase your body temperature to increase and help shorten your sleeping bag warming.Our body can only be more comfortable when we sleep at night.

2. Wear clothes in moderation

Some softer clothes can be used for thickened pajamas. Put the unwavering clothes that are taken off, grow up in the shape of the body, and put it on the side of the body to increase the thickness between the sleeping bag and the Tent.Fill the filling, reduce the speed of temperature loss, and strengthen the warmth of the sleeping bag.It should be noted that in the cold environment, please do not wear a jacket to enter the sleeping bag. It is recommended to wore only underwear to sleep, which will help quickly improve the temperature and sleep comfort in the sleeping bag.

3. maintenance with a front sleeping bag

1-2 days before Outdoor exercise, please stretch your sleeping bag 1-2 days, helping to give full play to his warmth performance in the wild until you leave the sleeping bag into a compressed bag before departure.The water sucking the sleeping bag mainly comes from the human body. Even in the case of extremely cold, the human body will still excrete at least a small glass of water during sleep.After the insulation cotton, the insulation cotton will be bonded and loses elasticity, and the insulation capacity decreases.If the sleeping bag is used for many days, it is best to dry it under the sun.Frequent cleaning Sleeping bags can also keep the insulation cotton elastic.

4. Keep air dry

When Camping in the wild, if time permits, the sleeping bag should be turned off in the morning, placed on the top of the Tent or dry, ventilated, and sunny environment, which helps to dry the sleeping bag, but avoid strong sunlight during the day.

5. Learn to storage

When storing, you can roll the sleeping bag once and squeeze out most of the air.Then spread the sleeping bag and put the sleeping bag irregularly into the compressed bag from the tail.It is not recommended to put it in a compressed bag with rolls, because long -term regular roll collection will cause sleeping bag surface to accelerate the aging due to unevenness.

What common sense should be understood by using Sleeping bags

1. Pay attention to use temperature

Any sleeping bag has a suitable temperature range, and different Sleeping bags have their own "temperature".The general temperature label consists of three data. The minimum temperature refers to the minimum limit temperature used by the sleeping bag, which is dangerous for users.There is also a comfortable temperature, which means that the sleeping bag uses the most comfortable ideal temperature.The other is the highest temperature, which refers to the upper limit of the temperature usage range, which is higher than this temperature. The user will be unbearable.This temperature only has reference significance. Specifically, it will vary from person to person and varies from the environment.Generally speaking, European and American native Sleeping bags are not suitable for Asians in temperature. Because Europeans are higher than Asians in terms of cold resistance, so we must pay special attention when choosing.

2. Pay attention to moisture -proof

Although the sleeping bag fabric has a certain waterproof or waterproof function, if the weather is extremely humid on the way, please seal the sleeping bag with a plastic bag to avoid humid air into the sleeping bag and reduce warmth.When Camping in the wild, the use of moisture -proof pads can effectively separate Sleeping bags from cold and wetlands to prevent Sleeping bags from moisture.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is valid. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt; error correction & gt; & gt;

Moss micro -landscape production method

Moss Micro Landscape Production Step: Put the light stone layer

Choose the diameter of the light stone about 3 ~ 6 mm. Since the glass bottle does not have a bottom stomach, the effect of the light stone layer is as the bottom breathable water seepage layer.When the light stone is laid, it should be as flat as possible. Don't be too high. Of course, according to the composition, the light stone is best to spread two layers. First, it is large particles, and then small particles.

Moss Micro Landscape Production Step: Play Water Moss

1. The role of laying water moss is to beolate, mainly to prevent soil from being penetrated into the light stone layer due to watering or rainwater. At the same time, we can also isolate the water storage and slowly supply water to ensure that the roots are not flooded.Here we tear the water moss into a small piece and a small piece, fluttering on the light stone layer, just a thin layer.

2. After spreading, spray the water moss and wait for it to slowly swell. At this time, the water moss is flattened with your fingers.

III moss micro -landscape production step: laying planting soil

1. To raise plants, soil is the key. The appropriate pH value, good moisturizing power, and certain nutrients, thickness and softness of Chengdu are important factors affecting plant survival and growth.Therefore, you should choose a plant that is more suitable for the growth of negative plants such as moss.

2. Put the amount of soil on the water moss and make a slightly slightly high slope of the front and rear, about 8 mm in front, and about 16 mm in the back.Then spray wet planting soil, but pay attention to controlling the amount of water. Do not exceed the light stone layer.

Moss micro -landscape production steps: planting background plant

This is the step of sowing. Those who have experience can be based on their own love, free creation, and their own small production. However, if novice, it is recommended that you install the steps provided by the shop to complete.

1. First use tools and other tools to dig a small hole on the soil, set the prepared plant root, and then pinch the mules, plant it in the soil, and reasonably surrounded the soil to ensure that plant planting is safely stable.In addition, the stems and leaves of plants are recommended to the super -view port.

2. Since it is a background plant, we must plant it in the back of the picture, but we cannot plant the roots to be planted, but the stems and leaves of the plant can be stretched in the upper part.

3. All plants can be trimmed appropriately when the branches and leaves are too large and too long, but do not hurt the main stem.In the case of too long, you can also trim it moderately, or gently roll the roots to the lower end of the main stem, pinch with a mule, and plant it into the soil.

Moss micro -landscape production steps: laying moss

1. clean the moss and divide it into several parts according to the requirements of the laying of your own design.You can lay some props, such as houses, rivers, and so on. After the moss is paved, remember to spray water again so that the moss can fully swell.

2. After the moss expands, you need to gently press it with your hands, so as not to leave the edge to leave a gap.

Moss micro -landscape production steps: laying river sand

1. Powder river sand with the reserved place to create a stream and the shallow beach in front.

2. In this bonsai, in order not to affect the previous work, vine plants have also been planted at this step.

3. It has become a scene. At this step, most of them have been successful.

Moss micro -landscape production steps: Place dolls and mushrooms

We need to play freely at this step. You can put the doll in your expected position according to your own understanding, and imagine the fairy tales in the scene. There are more artistic conception and interest.

Summarize: Above we briefly introduce you how DIY has fun moss micro -landscapes. If we put a pot of our DIY moss microman landscape at home or office, when we are tired and fatigue, I can see the green color carefully designed.Let us escape complication and hustle and bustle, and walk into a natural small ecological zone.

Moss micro -landscape maintenance method

Daily maintenance method

Light: Moss is a yin -ray plant. The demand for light is not so strong. You can place the bright scattered light throughout the day in the room, or the sun will be exposed in the early morning and evening.But it should be noted that it must not be exposed to the sun at noon.

Water: Moss is a plant that absorbs moisture directly by leaf surface. When watering, moss spray the leaf surface, and other plants spray the soil surface to prevent other plants from rotten leaves.

Although moss likes humidity, too much watering will also get sick, so watering should be appropriate.Daily maintenance can be done a little bit, and don't be too damp.The natural drying and dormant moss can be restored with water permeability, but the moss that is wet for a long time is easy to damage once the temperature is not suitable.

If the leaves are stained with water on the inner wall of the glass, the two are separated, otherwise the leaves will rot and stick to the inner wall of the glass.

Temperature: Most areas in China are suitable for moss growth, and the best temperature grows between 5 C-28 C.

Soil: Although moss in the micro -landscape does not require the soil, it is still recommended to use special cultivation soil, because this soil is not easy to mold.

Ventilation: If it is a sealed glass bottle, it is recommended to open it for several hours a day to make the plants breathe and increase air circulation.

Moss disease maintenance

Black: It is usually too little watering, or the open environment is too dry. You only need to replenish the water in time.

Yellowing: There are many reasons for the yellowing of moss. Generally, the conditions of light are not suitable. The soil is not suitable for moss growth, or the air quality is not good in an open environment.

Black: Usually, because the watering of the moss is soaked in the water, it starts to become black and rot.At this time, watering should be stopped and placed in a cool vent. If there is still too much water, you should slightly tilted the landscape, and then use a paper towel or water absorption cloth to absorb excess water.

Surface mold: This situation is generally due to poor ventilation. If it is not particularly serious, it should be placed in a cool and ventilated place, spraying bacteria reagents and accepting the morning and evening sunlight for sterilization and disinfection; in severe cases, it is necessary to change soil treatment.

1. What is a Tent

The Tent is a new type of Outdoor activity originating in Europe for temporary buildings, also known as European tents, and is lightweight. It is called "mobile real estate".It is widely used in temporary warehouses, factory buildings, temporary construction, exhibit tents, tenthouses, and emergency disaster relief.The Tent is a new concept for the international masses. It is also gradually appearing in people's daily outdoor activities in recent years., Convenient storage, small volume and other characteristics.

2. What are the characteristics of a Tent

1. Flexible and convenient

It is easy to install and disassemble, and the venue is free to choose in different environments.

2. Safe and stable

Aluminum alloy framework, steel parts connection, PVC tunnel high -frequency welding, base fixation, and strong mechanical properties.

3. Complete service

Pre -sale, sales, and after -sales tracking service, the problem will be feeded and resolved as soon as possible.

4. Satisfied personality

It can be designed and produced according to demand, producing a Tent, elegant appearance, and providing corresponding supporting facilities (hardware walls, high partitions, top curtains, edges, flooring, furniture, lighting, air conditioning, mobile toilet, European fence)

5. Wide applicable

Commercial exhibitions, festivals celebrations, catering and entertainment, logistics and storage, Outdoor leisure, convenience municipalities, etc., all kinds of Outdoor temporary activities are useful.

What are the types of tents?

There are many styles of the Tent, which can be divided into three types according to different appearances:

1. A -shaped Tent

The A -shaped Tent is also known as an activity Tent, which is the most widely used, and it can be used from Outdoor business to large exhibitions.

2. Scoop Tent

The bottom surface is Square, and the top of the canopy is like a tower spire, with an elegant appearance.

3. Ballical Tort

The dome is called "the strongest space, the lightest, and the most effective design."With a rigid and stable architecture, you can temporarily suspend light and audio equipment to decorate and fill your activity space.

4. There is also a type of Tent mixed with the characteristics of A -shaped tents and scoop tents.

Fourth, how to do the Tent

1. Positioning the bottom plate of the column

First determine the flat ground at the installation site, then position the bottom plate to determine the position of the four bottom plates and then measure whether the distance between the diagonal line is equal.If you are not equal, you must re -adjust the position. Be sure to ensure that it is a rectangular rather than a parallel quasoplasty.After better, fix the column bottom plate in the corresponding four positions, and use the same method to better and fix the other bottom plates of the length direction.

2. Place a good part

Section A section A, angle node, diagonal beam A, and diagonal beam B (two -section oblique beams with more than 14 meters), oblique beam undertaking parts (connected to section A section A and oblique beam B, 14There are no components below the rice span), the top nodes are placed, and all components form a gables. Putting other gable surface components in the same principle is placed in the same principle. Note that it must be placed on the ground in one direction.

3. Connect the diagonal beam A/B section

Insert the oblique beam A section A into the oblique beam to undertake, and tie them into two screws (Note: the small hole will not be installed first)

4. Install top nodes

Connect the connected diagonal beam AB section with the top node, the screws tied into, and tighten.If it is the first gear, you must also install the wire flower cable, and install the buckle on the one -end of the flower cable without flower cable on the second hole in the section B section B.Use this method to install all the top nodes and oblique beam AB sections.

5. Install corner node

Insert the oblique of the corner node into the section A section A, connect the upper end of the column to the straight end of the corner node, and penetrate the screw and screw the nut.If the wire flower cable and the cross rod are installed, the hole is installed with a hole on the top of the corner node, and the hole is installed with the hole in the lower end of the corner node.In the same way, install other corner nodes.

6. Connect the column and the bottom plate

Put the lower plug -in holes on the column to the screws connected to the holes on the bottom plate and tighten the nut.The same method connects other columns and columns.Note that the entire installation process must be gently put in lightly, and it is necessary to use wood to pad the assembled gables. When moving aluminum materials, be sure to lift the entire frame to avoid aluminum and sand and other sand and other sand and other sands on the ground.Item friction causes the surface of the aluminum material.

7, vertical mountain wall

All personnel are divided into four teams, two people pull steel ropes, and two people stand at the corner nodes. Others stand at the apex, lift the gables up, and lift them to a certain height.Continue to lift up.People who pull the steel wire rope should also pull up the gables up.

When the entire gables are erected to 70 degrees, they must stop, and then slowly stand vertical with the ground. At this time, the person who pulls the steel wire rope stood a slightly stable on the top.At the same time, several people have to support the pillars.Two people install the flat iron end of the cross rod to the screw below the upper end of the column, and tighten the nut.Connect the other end of the cross rod to the bottom hole below the bottom plate of the adjacent second gables, penetrate the screw and tighten the nut.Pose a second gable in the same way and install two other cross rods.

8. Install beams and bars

The cross -section shape of the beam is house -shaped, and the cross -section shape of the strip is Square.The hooks of the beams or bars are ended up, and then the hook end is tilted to the U -shaped ears on the corner node or in the -shaped iron on the corner node.Use a ladder to slowly lift the straight hook end of the beam/bars and hang it into the ears of the gables or corner nodes on the side of the hook.Under normal circumstances, there are three beams between the two gables, namely one end of the two ends and one in the middle of the middle. The bars increase or decrease according to the size of the span.

9. installation

Connect the middle support to the small hole in section A in section A, insert the screw, and tighten the nut.After installing the middle support, hang the side beam into the corner node and the middle -supported Hanging ear.Note that when the side beam is Hanging, be sure to install it from the side of the side beam, first hang the side beam accessories into the Hanging ears in the corner node, and then slowly lift the straight hook end to install it to the middle support Hanging Hanging on the hook above the support.In the ear, remember not to install the straight hook end first, otherwise the installation is unsuccessful.Like the beams and bars, you must first install it from the hook end, and then hang the straight hook end.

10. Install the top

Put on the hemp rope at both ends of the top of the top, and the strap is in the Tent.Then stuff the tape on both sides of the top end of the cloth into the slot of the diagonal beam, and throw the other end of the hemp rope from the entire frame of the Tent, and then pull the four people to the hemp rope at the same time, so thatThe groove slowly pulled to the opposite side.Remember to pull it hard at the same time, otherwise the top will be stuck and causing pulling. To solve this problem, you only need to pull back the top back to a certain position and then pull it back again at the same time. Be sure to go forward at the same time.The same method is used to pull other top tops.

11. installation side triangle

Similar to the installation cloth top also needs to use hemp ropes, but when installing the side triangle, someone must stand to the side of the (high ladder) top node. The only difference is that the strap of the side triangle is outside.First put on the side triangle into the slot of the diagonal beam, and then the people standing in the middle pulled up to the hemp rope. At the same time, when standing at the corner node, the side triangle was lifted to lift the side triangle to let the rubber strip go up the groove.When installing the side triangle, be sure to pay attention to the left and right points, do not install it.After pulling the two side triangles, the middle seam Tube is slowly pierced from the lower end between the two side triangles (a section of the rubber strip is cut off slowly (the middle seam Tube has a flat iron inside).When you put it on the top node, hang the flat iron into the ears of the top node.

12. Install the curtain

Open the curtain, facing the front (there are ropes or covers on it), first put the rubber strip into the pillar to milling.Then slowly pull up the top, plug the codes into the gap in the beam milling slot. Pay attention to stuffing one by one in order.Put in down, pull the curtain to the middle, and place the side of the rope on the side of the tun ring, and connect the rope from top to bottom.

13. Install the top pressure rod

Put the top pressure rod into the crusher cover of the top of the cloth (that is, there is a double -layer Sleeve at the top of the top of the cloth, then put the end pressing iron in the press, and put the rectangular screw in the seamless pipe of the angle node.The last step is to plug the crusher of the surrounding curtain into the bottom of the rod at the bottom of the curtain to prevent the wind from blowing the curtain.

5. precautions for Outdoor exhibition canopy

1. Selection of the venue

We all know that today's Tent products do not have too high requirements for venue conditions. Generally, the flat ground can be easily built, as well as Outdoor exhibition tents.However, in order to hold the activity safely and orderly, we still need to investigate the environment of the surrounding venue before the Outdoor Tent was built, and prepare the solution in advance according to the actual situation, so as to ensure the normal construction of Outdoor exhibition tents!

2. Determine the size and measure the venue

After we confirm the conditions for building the site, we also need professional staff to carry professional tools to the venue for measurement.If the site conditions are found to be unfavorable, you need to adjust it in time, and finally determine the Tent specification plan and fixed method.

3. Verify the time of use

After confirming the above two points, we also need to confirm the time when we need to use a Tent.In this way, a canopy manufacturer can arrange production plans, stocking, transportation, and construction based on the actual situation.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is valid. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt; error correction & gt; & gt;

one,compressionClothesHow to wash

You can check the laundry tags of the clothing before washing. Whether you can wash it, whether you can drift chlorine, you can wash the highest temperature, whether you need to clean it on the reverse side.clean according to the precautions of the washing label inside the clothes to avoid errors and cause the clothes to be damaged. IfcompressionClothesYou can wash it. It is recommended that you choose to use high -quality laundry solution.

If the clothes have no obvious stains and local cleaning, the laundry solution can be poured into the pot to dilute, and the clothes are soaked in the clothing for 20 minutes.

two,precautions for compressing clothes cleaning

Wash the water temperature below 30 degrees, no need to add clothing soft agents.Do not bleach, iron or dry.Avoid washing with different colors.After wearing in salt water, the low -temperature freshwater is fully rinsed.The same as most elastic clothing, the lighter the Compressed clothing washing process, the longer the service life.Finally, dry it in a flat, don't hang it!Try to wash the Compressed jacket as much as possible every time I run, and keep the Compressed clothes clean.

three,The service life of the Compressed jacket

The service life of the Compressed jacket depends on the frequency of wearing and the number of cleaning times.If sweat does not wash, sweat will slowly corrode the material of the Compressed jacket and accelerate aging.Generally speaking, the life of the Compressed jacket is about 2 years.

What do you eat when you travel in winter

Bring more portable high -calorie snacks

Winter travel is a pleasant exercise that tests physical fitness.To ensure physical fitness, of course, it is necessary to ensure supply.High -calorie snacks are very suitable for snacks for Winter travel.

1. Chocolate

Light weight, high calories, can provide calories quickly and efficiently when fatigue.

2. Compressed biscuits

Small size and sufficient heat. When the biscuits can be eaten, it is particularly easy to break. When traveling in winter, when you go out, you encounter a place with hot water. Put it into a piece of water and soak it with boiling water.On the one hand, hungry, on the other hand, drinking some hot things, very comfortable.

3.

Like compressed biscuits, the quality is light, portable, and calories.

Snacks that take a car to wear time

1. Duck neck

There are many major brands on the Internet. Remember to buy fresh clothes.The store is generally equipped with disposable plastic gloves. When you eat it, you can wear it without staining your hands.The duck neck not only enriched the boring journey, but also relieved.However, it is recommended to arrange a car on the road, and the process of switching between attractions is not convenient to bring it.

2. Melon seeds

This thing is always inseparable from travel, and all kinds of melon seeds will make the journey fully.But pay attention to your own image, do not throw melon seeds casually.

3, chicken feet

Not only can you spend time, if you have a mood, bring a few cans of beer, you will have chicken feet or duck neck.And it is also very embarrassed. Buying an independent vacuum packaging is very portable.

Leisure snacks that resist the hungry refreshing God

1. Biscuits and pastry snacks

Biscuits Cake snacks should be one of the snacks that are mostly selected. It is also a snack that people often eat in daily life.Going out to travel with some biscuits and pastry, you can fill your stomach to replenish your physical strength, which is still good.However, it should not be stored for too long, and the biscuits may be crushed on the way. Compared with other snacks, they may not be so convenient when they carry it.You can consider it according to the actual situation.

2. Preserved snacks

fruit snacks are also one of the most familiar snacks. Most of them are made of fresh fruits through a series of procedures such as dehydration and air -drying, retaining the sweet and sour taste of fruit and some nutritional value.Common dried mango, dried pineapple, dried strawberries, etc., so it is more suitable to eat some of them when traveling.And mango is also more helpful to prevent vomiting. If there is a motion sickness, you can try to eat some, it should be more comfortable.However, it is better to consult a doctor for specific conditions.

3. Sea -owned fish snacks

In addition, seafood snacks are also a good choice.Most of their production materials are different types of fish. fish are rich in vitamin B and collagen, which have a lot of benefits for the body.Moreover, seafood snacks can choose more flavors, some will be chewy, and some are relatively soft.When traveling in the car in the car, it may generally be more boring. If you like chewy, you can try eel shreds. When you are okay, chew, and relax it.

Moderate amount of functional beverages

1. pulse

Because sweating and the loss of electrolytes, it is necessary to supplement it in time, which is important for restoring physical alleviation fatigue.

2. Red Bull

In terms of physical strength, the effect of Red Bull comes very quickly.

The above drinks can not only supplement electrolytes and energy, but also taste.It should be noted that in addition to these drinks, the rest will bring pure water, and do not use a functional drink without sweating or no physical strength.

What is suitable for playing in winter

Although in the cold winter, we can't hide the mentality of we want to go out to play.But playing outside is very cold, so what should I eat with my friends in winter?Here are some foods that are more suitable for winter.

1As well ashot pot

In the cold winter, a hot hot pot is the best choice. A bunch of people sit around, eating, drinking and drinking is the most satisfying thing.

2As well asSpicy

Compared to hot pot, Malaysia can also bring you warmth in winter.Malaysia is more suitable for two or three friends to eat together, and everyone can choose their favorite food.

3As well asPizza

On the cold winter, a steaming and fragrant pizza is also a very good choice.Especially when taking the child to go out to play, it is best to choose this kind of food.

4As well asrice -rich rice noodles

During our breakfast, many people choose rice noodles.If you want to use the rice noodles as a staple food, you can choose the rich rice noodles that are rich in ingredients, which will make you eat it yourself.

5As well asmilk tea

Although drinking milk tea often makes people fall into the embarrassment of obesity.However, winter is used for fat, and warm milk tea cannot be missed.

6.fried chicken

Now many fried chicken shops, a fried chicken that has just been out of the pot, can make people appetite.However, this is only suitable for small snacks, and it is not suitable as a staple food.