1. Why is the fishing line broken

When fishing, the most depressed thing was that it was easy to catch a fish, but the fish line was broken when the pole was lifted.Many people will complain at this time that the quality of the fish line is not good. In fact, there are many reasons for the fish line break, including:

1. Old residual secondary lines lead to disconnection

(1) Old line:First of all, it is manifested in the judgment of whether the old line can be used. Some fishermen took a long time, caught a lot of fish, regarded it as a contributor, and could not change it.Change the line.In fact, even if it is a good fishing line, after a long time of sunlight, the ultraviolet destruction effect is very strong, which will make the fishing line rigid and gray and brittle, and the tension is greatly reduced.Furthermore, the fishing line has been dragged many times, which may be deformed, or flat or thin.Sometimes due to being squeezed or compressed, or a dead bend, it becomes a hidden danger.Therefore, it is necessary to check it frequently when using the fish wire. Those with "pathological" should be replaced. The fishing line is a consumables that should be changed frequently.

(2) Line:The inferior line is charged and mixed in the high -quality fishing line. These wires have a small tensile force and a large extension.There are also some Fishing lines. The original quality is good. Later, because the storage time is too long and deteriorates, from superiority to inferiority.Using this fish wire may also be easily disconnected.

2. Improper nodules cause disconnection

The nodules on the fishing line are also the main reason for disconnection.During the knot, the two lines are twisted with each other to produce the cutting effect. The knot is too tight to easily flatten the fishing line, and the flat line is easy to break.

The nodules on the main line of the hand pole are at both ends, and the upper end is connected to the fishing rod. Most of them are lively. The tip of the pole tip is connected to the line. Because it is a double -stranded Sleeve, the line is not easy to break.It is best to connect to the fishing line and the fishing group. It is best not to use the word "".

The most concentrated part of the broken line is the sub -line. Usually it is smaller, shorter and thinner than the main line, and there are nodules at both ends.The most common broken lines are tightly tightened because the hook is tight. Press the sub -wire to flatten, and the sub -wire will be pulled off from the hook handle after the fish hook is stunned.If the sub -line is led from behind the hook, it is most likely to be cut off by the gear head on the hook handle.

3. Improper operation causes disconnection

Because the big fish is really rare to pull the fishing line directly, because the fishing rod is supported by the fishing line as a strong support. After the fish is put on the fish, the tension is passed from the fishing line to the pole.Function, at this time, the fishing rod will play a soft and hard elasticity. It is thicker one by one, one section one by one, from the tip of the pole to the handle.The stronger its tensile resistance, the fish is not moving, and it stands straight. It is this "soft power" that relieves the death of the big fish, and it also protects the fishing line from being damaged.

Of course, the tension of the pole also has a limit, and a certain force pole will be broken.Due to the hard power of the pole, when the fish is not moved, its strength is concentrated on the fishing line, causing a disconnection.So many fishermen know that the hard pole is easy to break.Not good at using the elasticity of the fishing rod, such as the fish or hook Hanging the bottom, pulling the line with your hands, no elasticity in your hands, hard touch, and the fishing line is likely to be pulled off.This method of dragging the lines is a strategy to preserve the safety of the pole line when the hook hangs.

There is also a break -up moment that is most likely to happen and often ignores. It is that after the big fish was copied and copied ashore, it folded and fought on the shore.Drag, the sub -line will break.Therefore, the fish in the copy of the net must be solid, not to make it toss, neither hurts the hands nor break the line.

Second, how to pick up the fishing line is the most strong

In the daily fishing process, everyone often encounters unexpectedly disconnecting situations. In the case of disconnection, the disconnection on the hand can be used to use it. The specific method step is:

1. Flat the lines of the two fish lines, and try to flatten the lines as much as possible. Do not have different lengths.

2. Put the two side -by -side fish wires around the fingers (can also be two laps), and then twist an eight -character buckle.

3. Put the two side -by -side heads from the outer eight -character hole.

4. Pull the two line heads in the right hand, pull the two lines on the other side of the left hand, and pull it hard.

5. Use scissors to remove the excess line head. After cutting, you can use a lighter to bake the line head slightly to make the head head flatter and the wiring is completed.

Third, can the fishing line be broken after being broken?

Many fishermen think that it is not strong to connect the fish wire. This kind of worry is original. After all, a knot has been knotted on the fish line.Compared with fishing, it can be connected to the line and re -use it. It is much stronger than Linyuan's envy fish. Moreover, we are generally connected to the main line. Generally, the main line is one to two larger than the sub -line.It is okay to deal with normal fishing feelings.

When using the connected break, pay attention to the following points:

1. Do not be too fierce.After all, we are not using a complete line, and the excessive rod will cause the fish wire to be disconnected from the knot.

2. It is not recommended to use a hard tone fishing rod.After all, the receiving line is "injured". Using the ultra -hard fishing rod will accidentally increase the force at the knot (unless your method is super well -skilled), it is recommended that you use 28 tunes or softer poles.The advantage of using this fishing rod is that you can make full use of the rod to protect the fish wire slightly.

3. Do not use it for a long time.It is a way to connect the fish wire with it. During the secure period, as long as the conditions are mature, it is better to replace it with a fish wire without joints.

1. What are the types of fish wire wheels

1. Closed fishing wire: Consistence of components such as the rocker arm to stop the bond, the scroll scroll cover, and the qualifying holes.

2. Digital display drum -shaped wheels: a drum -shaped wheel with electronic display, usually a special wheel of sea fishing.The bait is thrown into the sea fishing Ship to accurately show the depth of the seawater and the length of the fishing line thrown, and is mostly used for sea fishing.

3. The spinning wheel, spinning -type fish wire, also known as the rotation type, is the most common one, and it is also the most useful use of rod fishing enthusiasts.Its advantages are light and flexible, simple structure, and convenient use.The fishing line of the spinning model is mainly used for sea (light) water fishing in natural waters such as rivers, lakes, and reservoirs.

4. Flying Wheel: It is the main wheel of flies fishing, and it is also the abbreviation of fly fishing line wheels.Generally made of aluminum alloy or zinc alloy materials, mainly large and medium -sized models. Because flies fishing mostly use hollow Fishing lines, and there is a variable diameter (the line head is thin, the middle is slightly thick)The groove is slightly thicker than the average fishing line chakra.Because the throwing of the fly fishing method is different from the throwing fishing method, it has the characteristics of simple structure, lightweight and flexible.

5. Double -axis drum -type fishing wire: Also known as the tough roll wire, because of the advantages of dual bearing and curls, the diameter of the rolling line grooves is small and the speed is small and the speed is fast.The length of the fishing line is mainly used to configure the heavy -duty rods of sea fishing, used for sea fishing. The main fishing target fish is a seawater fish with large individuals and strong struggles.Because the double -axis drum fishing line is used for fishing, the fishing line should be reinforced before fishing to prevent loosening when the big fish is loose.

6, fork -type Fishing lines: also known as hand wheels and earth wheels.It consists of a shaft rods, rolling wire grooves, fork -shaped wheel leaves, nuts, snail tie and other components.The structure of the fork -type fishing line wheel is simple. It usually uses 6 to 9 waiting fork tooth to fix it on the shaft head.With fixing, relax or tighten the fixed snail tie when putting or closing, and the fishing line will rotate by itself.

7. Drum -type fishing line: referred to as drum -type wheels.It is usually composed of components such as rolling grooves, stop rods, side panels, wheels, and balanced hammers.It is mainly used to match the large and medium -sized rods in the deep -depth sea fishing, beach fishing and rock fishing.The specifications are relatively complete, with large and medium -sized models. The wheels are equipped with three control switches, including opening, half -stop, and stopping. Its structure is simple and the wheels are light and durable.

8. Drum -type single -bearing Fishing lines: consisting of side plates, stop rods, roll wire grooves, rocker arm, balanced heavy hammer feet and other components.The rolling lines are like a drum -shaped, which is larger than the fishing line of the spinning model.There is a switch below the bearings. There are stops, half -stop, open, three knobs, and have better performance.

2. How to choose a Fish wire wheel

1. Choose according to the fishing category

If there is a large fish in the fishing waters, a large wound wheel should be selected because it will have more storage lines.If you use a long pole, you should choose a large wheel.

2. Select according to the fishing waters

If you use a high and mid -range pole, you should choose a high and mid -range wheels, and the low -end rod should be equipped with a low -grade wheel.If the waters are wide, they must be used to fish for remote shots, and larger fishing ships need to be used.

3. Choose the performance of Fishing rods

According to the length of the sea pole, the length of the sea pole should be used, and the large wound wheels should be used. The sea pole is short. It can be equipped with a smaller wound wheel.The rear drainage winding wheel is easy to operate and easy to fine -tune the strength, but the price is higher. If the economic conditions permit, the selection of rotary fishing ships is better.

4. Select according to the method of fishing

To check the appearance of the wheel, to see if the appearance of the wheel body is flat and Smooth, whether the paint surface is dazzling and non -destructive, whether the tone and the words are clear and beautiful, and the wheel body and attachment are damaged and cracks.If you use a hook fishing, because the hooks can generally only catch a small fish with small individuals, a small fishing wheel should be used.

5. According to the price of fish line wheels

The Fish wire wheel affects its appearance parameters. A fishing Ship will show its number of bearing. Of course, the number is more and more expensive. In fact, the number of general fishing Ship bearing is enough.More than 10 or more can only increase costs, without too much necessity.

1. How to install the Luya water drop wheel

The method of launching the Luya water droplet wheel is very simple. The specific operation is to first pass the fishing line through the wire ring, then tie the fishing line on the online cup, and finally shake the handle to wrap the fishing line around the online cup.It is worth noting that the line cannot be installed too full. Generally, it is recommended to load the lines of the line cup is about 1.5 to 2.0 mm. The fishing line is too full of throwing.

2. How to adjust the Luya Drop Wheel will not bomb the line

To adjust the Luya water drop wheel to avoid the frying line, you can follow the steps below:

1. Mechanical braking adjustment:First adjust the mechanical brake. This is usually located on the side of the rocker arm. The mechanical brake is adjusted to the critical value of shaking and not shaking from the left and right of the wire cup. This goal can be achieved by fine -tuning the knob.

2. Magnetic braking adjustment:For magnetic brakes (commonly in water drops), the brake strength can usually be adjusted through the numbers on the knob. The larger the number, the stronger the brake power, the more stable the throwing.Gradually reduce the gear until the appropriate gear of the non -fried line is found.

3. fish line match:Choose nylon or woven wires to avoid using carbon lines because the carbon line is hard and easily leads to frying lines.

4. Wire shaft fine -tuning knob:Adjust the line axis to fine -tune the knob to ensure that when the fake bait is free to bottom out from the tip of the pole, the wire cup does not bombard the wire.

5, disclosure adjustment:Adjust the disclosure knob to ensure that the thread cup is properly loose during the throwing process to prevent bombing.

6. Practice throwing:When practicing throwing, pay attention to the movement of the thumb pressure cup. As the skill improves, the brake gear can be gradually reduced to achieve the best throw distance without bombing.

Through the adjustment and practice of these steps, the situation of the line can be effectively reduced or avoided.

1. Several types of fish wires are divided into

The fish line is one of the important components of fishing tackles. Whether the fishing line is properly related to the fishing effect directly. For example, the choice of the type of fish wire is to pay attention. There are many types of fish lines. According to different classification methods, different types can be divided into different types:

1. According to the material

(1) nylon line:nylon wire is also called traditional lines or four -color lines. Generally, resin materials are made of resin materials. It is made of machining filaments. This fish wire has no color transparent, strong tensile, good elasticity, fast water cutting, and high fishing sensitivity.Durable, durable, soft, not easy to be crispy in winter, and verticality, so the nylon line occupies a dominant position in the market.

(2) Carbon cable:Carbon lines mainly refer to a fish wire made of carbon materials during the manufacturing process. This carbon -based fish wire is more abrasion -resistant, but the ductility is poor.The proportion of the carbon line is greater than the proportion of water, so its water cutting is better, which is more suitable for use in the rock fishing.Because the texture of the carbon line is relatively hard, it is often used for the eldest son line or tie of the Ship fishing.

(3) Weaving:It is a fish wire woven from multiple silk threads. The early weaving lines did not add a membrane, it was easy to absorb water, and it was not easy to maintain. However, because of its abrasion resistance and tensionHousekeeping, but the water cutting is poor.There is also a waterproof woven wire that adds a membrane technology during the manufacturing process, which is made of multi -stranded weaving lines, also known as fire lines.This weaving wiring is also good, but its damaged part is easy to form a hair ball, which is easy to break and the texture is harder.The fusion line is a weaving line that adds a multi -bhomistarian nylon line to the weaving line, and in this process.Its advantages are high tensile values and abrasion resistance.Because the nylon wire is added to the production, this thread is softer than the normal wiring and good back.

(4) Ceramic line:The ceramic line is made of high -molecular aggregate materials. In the formation of the online body, it is made of special resin to fill the spare special resin to improve the tensile strength and waterproofness of the fish wire.Then add the second layer of special resin to enhance the wear resistance of the fishing line.Finally, add special resin to the third layer to improve water resistance.The fish wire of the ceramic line has excellent tensile strength and abrasion resistance. It is not easy to nodule, light quality, and the feedback of fish feelings is more sensitive.

(5) Ultra -strong PE fiber fishing line:Taking the super PE fiber as the raw material, the surface of the thread is added with a lubricant to improve the layer on the surface of the fish wire.This material of the fish line is durable, long -lasting, and can prevent wear and fading, reduce tangels, and knots are more convenient. It has the characteristics of resistance, no cutting wires, durable performance, and fine line diameter. It is suitable for fishing as fishing.Line, kite line, water sliding traction line.

(6) Synthetic fish line:The synthetic fish wire is the process of adding other materials to the finished product during the production of the nylon line, so that the line can float on the fishing line that floats on the water or suspended in the water.Suitable for the semi -floating water line as the rock fishing, the full floating line containing the parade material, and the resin processing lines to add tensile substances.

2. Press the source of the fish line

It can be divided into three types: domestic, imported and joint ventures.The raw materials produced by joint ventures come from imports and are processed and produced by domestic. Many people like to use the lines produced by China -foreign joint ventures, because their prices are cheaper than imported, and the pulling force and technology are also applicable.

3.

It can be divided into powerful lines, super -powerful lines, and strong strength lines.

4. Press the color score

There are many types of white, light blue, dark blue, yellow, light red, color lines and other types.

5. Divide in fishing

It can be divided into competitive lines and leisure lines. The competitive line is a fish line designed for competitive. The leisure line is a non -professional line designed for the low requirements of the line.fishing people.

Second, which type of fishing line is easier to use

There are many types of Fishing lines. Different types of fish lines are suitable for different fish feelings. Generally, it is not easy to say which fish line is best. When choosing, it is mainly based on the fishing environment and the types of fishing.EssenceA good fish line generally requires the following four requirements:

1. Good liquidity

The so -called liquidity is that the thread remains less in water after water.

2. Strong tension

That is, strong, durable, and not easy to break.The Fishing lines sold by Fishing gear stores will indicate the tension of the fish line on the outer packaging, which can be purchased according to the needs.

3. Do not bend and deform

No matter how entangled the fish line, it is vertical after letting go.The curved thread is easy to make the hook in the water tilt, the fish is not easy to hook, and it is easy to decide.

4. soft

Whether it is a thick line or a thin line, it should be soft, and it should not be hard after a period of time, indicating that it is a good line.

1. The difference between the fishing carrier 3 axis and 12 axis

1. The number of bearing is different

3 The number of bearing in the internal rotation part of the fish line wheels equipped with a shaft sea pole is 3;12 The internal rotation parts of the fish line wheels equipped with a shaft sea pole are 12 bearing.

2. Different friction

The more bearings, the less friction, the smoother rotation, the faster the closing line, the easier.In theory, 12 axes are less friction than 3 axes, and the lines close faster.

3. Different prices

The price of the 3 axis of the fishing Ship is relatively low, and the price of the 12 axis of the fishing Ship is higher.

4. Different weight

The fish line wheel of the 3 axis is small, the structure is simple, and the weight is light; the 12 -axis fishing Ship is heavier than the 3 -axis fishing Ship.

2. How many axes do the fishing Ship buy?

The fishing wheel axis means rolling axis. In other words, the two circles are together, and then some steel balls are placed in the middle, which can mainly play the effect of sliding friction and lubrication, which will make the fishing wheels use smoother.But this is not to say that the more bearings of the fishing wheels, the better. The gear combination of the fishing wheel only requires 5-8 bearings. Generally, the number of axis should not be less than 5.The number of fishing ships will also increase the weight of the fishing Ship.Therefore, the axis is not the only reference parameter when choosing a fishing Ship.