1. Why should the surfing board wax

surfing board is a Tool for our entertainment. Of course, no matter how good the surfing board is, it is also necessary to wax. The waxing surfboard can effectively increase the friction of the human body and the body.Sitting on the surfboard is easier to sit straight.

surfing plate wax (non -slip wax) is a special wax, mainly composed of wax, vegetable oil, pine fat, resin and natural essential oil.Generally, two waxes, bottom wax and facial wax.3a2418-24Water temperature is 14-18 C), and the cold water wax (below the water temperature below 15 C).

2. How to maintain and clean the surfboard

To make the surfing board play the greatest role, it is essential for maintenance and maintenance. So how to maintain and clean the surfboard?

1. surfing plate cleaning

Rinse and wipe it after each use. The sea water will cause considerable damage to the completeness of the surfing plate, especially when it suffers from some collisions and impacts, the salt section will cause damage from the inside through the small wound of the salt.Rinse with fresh water after each surfing.This is easy to achieve, and it will not take up too much.

In addition to rinse, deep cleaning is needed after several surfing.Depending on where you surf and the frequency of stay in the water are maintained in different ways.

2. surfing maintenance

(1) Ready to open board

The first step is always the most challenging.The first step is to confirm that there are no old, sand and dirty wax on the board.It takes a little time to clean up the old wax and place the surfboard in a sunny place.The sun helps to soften the wax.In this way, it is easier to melt and harden.With no sun, you can use hair dryers. Whether it is from the sun or a hair dryer, pay attention to the heat.

(2) Cut the diagonal line with a wax comb

Before waxing, scrape the wax on the surfboard with the knife surface of the wax comb and clean it with cloth. If you can't find a wax comb in a while, you can get a plastic card or replace the wax comb.The surface layer was scraped almost some warm water on the board.Softening the residue in warm water, wipe it off with a wet cloth.

(3) Use a surfboard to clean spray

After the warm water is cleaned, there will be some residues on the plate. In order to clean it more thoroughly, you can use a surfboard to clean the spray.Apply the surfing plate evenly, and finally wipe it clean according to the use time on the instruction manual.

(4) Apply with coconut oil

The last step is to completely wipe the entire surfboard.Apply a thin layer of coconut oil to protect the body.Apply a layer of fresh wax or fine processing spray after air drying.

1. Is there a fixed on the foot of the surfing board?

surfing is a very popular maritime movement. Its gameplay is stimulating and can make people feel the feeling of shaking with the wind.For beginners, surfing is a difficult movement. Many people are curious before watching other people's surfing. Is there fixed ones under the feet of the surfing board?

This is certainly there. After all, the skateboard is on the ground, but the surfboard is in the sea. If it is not fixed, it will be run away.

2. How to fix the surf panel foot rope

The previous article has simply understood that the feet of the surfing board are fixed, and the role of this role is our foot ropes. So do you know how to fix the surf board and foot rope?

The binding position of the foot rope is at the ankle behind the back, and you need to pay attention to the head of the rope when you bundle your forehead, so that you will not be tripped up when you stand up when you play the board.Generally speaking, choose the same or the same or the length of the length of the length according to the length of the surfing board. The diameter (thickness) of the foot rope also affects external forces.The foot rope, otherwise it will cause burden.

Of course, if you encounter danger and want to start swimming and escape, you must open your foot rope at the fastest speed so that you will not be affected, and it is best to play with friends when playing surfing, so as to ensure your own safety.

1. What is the electric surfboard

Electric surfboard is a surfboard driven by lithium battery.A built -in lithium battery can provide the motor for about an hour of kinetic energy.At first, the surfing board was used for entertainment, but it was favored by the rescue team and lifeguards soon. The cost of this weight water Tool is low, which is more convenient than ships and jet boards. It can be used for rescue.

2. What is the principle of electric surf board

I have briefly understood what the electric surfboard is, so let's take a look at the principle of electric Surfboards together.

The shape of this surfboard is very peculiar. In addition to the "deck" standing, a longer rod is connected below, and a small water wing is installed at the bottom of the pole.

This wing is the core component of the electric surfboard. It looks like the wing of an airplane. Using the principle of Berinley, the place with a large flow rate is small, so on both sides of the wing wings, it can form obvious pressure pressure on the wings.Difference.

Then under the drive of the propeller, the surfboard can slide forward. When the speed becomes larger, the pressure difference between the sides of the wing wings will increase, so that the surfboard can be lifted out of the water surface.Like "flying" on the water, the operator only needs to master the balance, and the control of speed and direction can be achieved through the remote control in the hand.

1. Who invented the surfing board

The first design revolution in the surfing board appeared in 1926. A man named Tombraker invented the hollow board, applied for a patent, and became a surfing celebrity at that time.In fact, this is the improved Euro board. He made a lot of holes on the mahogany to reduce light weight, and then sticked a thin wood piece on both sides and waterproof.Holding it may be like holding a sister paper.At the beginning, many Hawaiians laughed at him and called this plate called 'cigar plate', but when they saw the performance of this board, they didn't say anything.In 1930, the board began to mass production. In 1935, he invented the board fin, which greatly improved the stability of the board.

2. What is the development history of surfing boards?

The surfing board was about 5 meters long and weighing 50 to 60 kg.After the Second World War, a foam plastic board appeared, and the shape of the board was also improved.The surfing board is 1.5 to 2.7 meters long, about 60 cm wide, 7 to 10 cm thick, flat and flat, the front and rear ends are slightly narrow, and there is a stable tail fin at the rear.In order to increase friction, there is a waxy outer membrane on the board.The weight of all surfing boards is only 11 to 26 kg.

There are some ripple structures on the front side of the whale wings, which helps this behemoth to move forward in the water more elegantly and smoothly.This structure can help reduce resistance and help the humpback whales "seize" the water flow, so as to ensure that it can still act quickly although it has a huge body.Inspired by this, surfing board producers produced a ripple -like front end of the surfboard.

1. What material is good for surfing board

surfing plates are generally made of glass fiber and carbon fiber. Now high -end surfing boards are more popular with carbon fiber materials. The reasons are as follows:

1. Light weight.The weight of the carbon fiber is a quarter of the steel, which is lighter than glass fiber. Ordinary glass fiber Surfboards are about 15 kg. People who go to the sea will naturally want the lighter the weight.question.

2. High intensity.The intensity of carbon fiber is 4 times that of steel. As we all know, the impact of the waves is very large. If the strength of the surfing board is too low, once the force is damaged, not only can it be experienced to get the fun of exercise, but it will also threaten people's personal safety.Essence

3. Corrosion resistance.In addition to oxygen and hydrogen in the seawater, there are chemical factors such as CL, NA, MG, S, CA, K, and BR, which are alkaline.The surfing board is soaked in seawater for a long time, which will be corroded.The chemical properties of carbon fiber are stable, with acid and alkali, corrosion resistance, aging resistance, and long service life.

4. Good balance.surfing in the sea, its own control technology is very important, and the balance of surfing board is also important.The carbon fiber has a strong Earthquake resistance and good balance. People stand on it, which is not much different from standing on the ground.

5. The design is clever.The carbon fiber waveboard is personalized and customized, which can be designed as a variety of styles to meet the needs of different users.For example, folding, combined, long boards, short boards, gun versions, soft boards, floating plates, Paddle boards, etc.

2. What is the size of the surfing board?

The surfing board was about 5 meters long and weighing 50 to 60 kg.After the Second World War, a foam plastic board appeared, and the shape of the board was also improved.The surfing board is 1.5 to 2.7 meters long, about 60 cm wide, 7 to 10 cm thick, flat and flat, the front and rear ends are slightly narrow, and there is a stable tail fin at the rear.In order to increase friction, there is a waxy outer membrane on the board.The weight of all surfing boards is only 11 to 26 kg.