1. How to sunscreen with balcony furniture?

The most maintenance of furniture on the balcony is sunscreen. When the sun is sufficient, it is not good to expose the furniture in the sun for a long time.Then teach you a few balcony Outdoor Furniture sunscreen tricks.

1. Plasses, sunshade, etc. cover the sun:If the balcony furniture is often exposed to the sun, it will quickly aging and affect the service life. Therefore, you can use the sun to sunscreen.Block the sun.

2. Lightweight furniture back to the room:Outdoor balcony furniture should be as light as possible, such as some folding tables and chairs, etc., when not in useIt is better to put it indoors. When you use it, you can avoid the problem of sunlight to a large extent.

3. Dales of large -piece furniture:But if it is always on the balconyfurnitureWhen we use it, in fact, there are many techniques that need to pay attention to use.You can choose some cloth to cover it. For example, the balcony sofa can be blocked with a sofa, which is good -looking and Sun protection.

4. Set the furniture storage room:You can select a furniture specially stacked on the balcony and cover it with a cloth.In addition to this technique, in fact, a storage room can be set when decorating to store balcony furniture.

Second, balcony storage cabinet sunscreen maintenance

1. Usually, the clothes that do not wear at home can play a certain role.

2. The top of the balcony can be used as a sunnic curtain.The Shading top effect is excellent. When the sun is very large, it is rolled out; when the light is needed, and the bright sunlight is needed, it is good to pull aside, and it is manual and electric.

3. In addition to doing a good job of Sun protection, it is also necessary to regularly and wipe the storage to clean up, such as using some clean rags, or detergents, etc. In fact, it is very simple.Or at home nanny pay attention to maintenance.

1. Method of Niuxianggui Breeding Method

1. Soil sour

Sun Xianggui is suitable for growing a little bit of acidic soil.The fertileness of rotten soil and peat soil is very suitable.You can also be mixed with perlite or fine sand.

2. Watering in moderation

Ri Xiang Gui watering should be moderate, and the soil is the best in a slightly humid state.spring and autumn, watering once every 2 to 3 days, watering once every 1 to 2 days in summer, and watering in winter once every 3 to 4 days.Especially when the root water is just planted, the first time I need itWater, then watering a small amount.Excessive or wetting can affect the growth of the plant.

3. Passionate light

The sun incense and Guiyang must be more common in order to make it grow more vigorously, and the fragrance will be stronger.The temperature control is best at 15-30 C. When the temperature is low in winter, it must be taken to keep warm to make it flowers.

4. Keep humidity

Sun Xianggui also likes a gentle growth environment. The humidity should be kept about 80%. It is dry in summer and autumn. In order to keep the humidity, you need to spray water and watering at the leaves.winter is very cold, do not spray water, so as not to cause the root of the sun in the sun in the pyramid.

Second, Niuxianggui's breeding precautions

1. Timely trimming

Sun Xianggui must be trimmed in time. Their growth period is very long. The long branches and leaves, the weakness and the yellow branches and leaves must be cut in time.In this way, the nutrition of the plant can be fully guaranteed.And in the just -planted Rimi Gui, you must cut some tender branches. After the tender shoots are germinated, you should also cut it in time.

2. Diligence and thin fat

Sunframe osmanthus period is too long, so it needs enough nutrients to ensure its nutrition.Phosphorus and Potassium fertilizer is the most suitable Fertilizer for Japanese cinnamon. It can provide sufficient nutrients in Nikko Cinnaba to keep the flowers continuously.The Fertilizer is the most suitable for Fertilizer in August in autumn. The average is 10 to 20 days on average. It is best to apply Fertilizer once a flowering period.

3. Change the basin every year

Ri Xianggui needs to change the pots every year, otherwise the long -term flowering will cause the soil to miss the nutrition.It is best to change pots from 2 to March each spring, and autumn is the best in September to October.Be sure to keep a part of the original soil, add new Nutritional soil, then pour water, and then let it grow normally.

Third, the diseased and insect protection

1. The most common pests in Nikkei are leaf blight and anthracnose.Both of these diseases can be removed with bacteria.In addition to the multi -bacterial clearing, the Tapin Pinotrane 800 can also be sick after being diluted.

2. Most of the pests are shell worms or red spiders. After 1000 times the water is diluted, spray can be sprayed to remove insects soon.

bamboo rattan is the same natural material as wood.Although they are two different types of materials, they have many common features in materials.Many of them are the same in processing and structure, and can be used together.bamboo is hard and strong.The surface of the rattan is Smooth, tough, elastic, soft and elegant.bamboo or rattan can be used alone or combined with wood, metal and other materials.Ordinary bamboo rattan furniture includes round bamboo furniture and vine furniture. Its structure is relatively the same, usually divided into two parts: skeleton and surface layer.

1. Choices of bamboo and rattan raw materials

There are many types of vines, known600The species, among them, the most commonly used in Miru, red vine, sand, and Badan vine.The thickness of the Badan vine and sand is generally uniform, which is a good material for making vine chairs. The flexibility of Rito is very good, and it is an indispensable raw material for making disk flowers.

2. Machining tools for bamboo vines

This isIt is often used when making bamboo and vine furnituretools: Warbers, high -pressure air cooling guns, operating desk.The setting of the operating table is relatively simple, but it is a lot of use. It is the main Tool for vines.There are on the operating table2The diameter is respectively8Cm25The iron -shaped cylindrical body of the cm is fixed on it, and the distance between the two iron cylinders is10CM.The process of our curved vines was done on this operating table.

Third, bamboo and rattan raw material grinding

The surface of the rattan is relatively rough, and it is a piercing plant, so when making it, the raw materials must be carried out"Practicing" treatment.This kind of polishing machine Tool is a Tool for grinding the raw materials of the vine, mainly using the sag and the grinding wheel to polish.The polishing should be divided into two times to complete, once it is polished, and the other is finely polishing.

The first step is rough

Roughly polishing, using80The type of coarse Belt; placed the rattan between the grinding machine and the grinding wheels, and slightly forceful to make the surface of the rattan basically Smooth.

Step in the second step

After the first round of polishing, the surface of the rattan was already much Smooth, but it was still slightly rough. At this time, the second round of fine polishing was needed.Now we use this180Follow the fine sofa Belt again,180sofa Belt ratio80The type of sand band is thinner, so that the grinding vines will be smoother.

Fourth, bamboo vine furniture manufacturing process

Skeleton: Types of the structure of the skeleton.

The skeleton of bamboo and vine furniture is mainly made of bamboo raft and thick vines.It has a strong anti -frustration, elasticity, easy bending, simple structure, and beautiful appearance.There are four types of skeletons:1All of them are composed of bamboo or rattan.2It consists of bamboo and vine, which can make full use of the characteristics of the material and easy to process.3Metal frames, weaving sitting and back on the frame.4A wooden frame, woven the seat and back on the frame.

The method of connecting the skeleton.There are three basic methods to join the bamboo vine frame.

1, Bending method.There are two methods of curved bamboo vine materials: one is a bending method, with a small diameter of bending.The other is a razor bending method with a large diameter, that is, a part of the curved part is dug out to form a concave for bending.The small curvature method applied to the frame bending is to dig a small part on the curved part, hold another bamboo vine material, and use bamboo needles to nail on one side of the curved side to prevent sliding.

2, Entangled.Also known as vine leather entanglement, it is the most common structural method commonly used in bamboo and vine furniture.The main feature is that in the connection part, it is entangled with the rattan leather, and the bamboo frame should be perforated on the link first.The rattan frame should be nailed together, and then the fragments are entangled with the rattan.There are three entanglement methods based on their part: one is for two or more entanglement.The other is to tie the two strips in the direction of each other, and they are divided into curved entanglement.Joint joints are connected to the broken.Each is connected in the middle part and is used in the middle part of the two rods in the horizontal direction.In addition, a single bar has rattan Skin to enhance the touch and decoration.

3Covering method.This is a unique combination of bamboo furniture.It is used to connect two different diameter bamboo rafts and make holes in the large bamboo Tube.Then, insert a suitable small bamboo Tube and lock it with bamboo nails.Scattered on wooden boards or vines.

one,Baby sleeping bagWhat is the difference from a jacket

Sleeping bags are used when the baby sleeps. It has good warmth, with three types of legs, envelopes, and gourds.The baby's clothes are also called Ha Yi. Harbin clothes make the baby very cool throughout the summer. The full -fleda design is convenient for the mother to change the diapers for the baby.Avoid the baby's belly because of kickingEssenceIt can be worn alone in spring and autumn. It can be worn in the cold and it can be worn inside as underwear. It is very comfortable. It is a must -have clothes for the baby!

Can the baby's jacket be used as a sleeping bag? It mainly depends on the thickness and warmth of the coat. As long as it can ensure that the baby is not cold, it can be used as a sleeping bag.

two,Baby sleeping bagDo you still have to wear clothes inside?

Sleeping in the baby's sleeping bag must be worn. If it is summer, you also need to wear a thin single clothes. You cannot directly let the baby wear a sleeping bag to sleep.harm.If the sleeping bag is rough or the quality is not closed, the baby may have allergies.

The role of sleeping bag is to protect the baby when he sleeps halfway, and then a cold.If you don't wear clothes, you can wear a sleeping bag directly, and the effect of keeping warmth is actually not good.One more layer of clothes can maintain the body temperature of the body. Do not have a decline in the body.

Be careful not to make it too tight when using a sleeping bag, it is best to be loose.However, if the loose sleeping bag is free, the wind can enter freely. If you do nt wear clothes, it s no different from the naked baby to sleep, so the sleeping bag does not play a role, so you need to put on your baby in the sleeping bag anyway.Even very thin clothes.

What is the general height of Outdoor Wall lamp installation?

Because the distance is determined by the effect of lighting, and the convenience of installation and maintenance is needed, the installation height of the general corridor and the Outdoor Wall lamp of general corridors and corridors should be slightly more than 1.8 meters high, which is about 2.2 to 2.6m from the ground.However, if you are on the workbench, you need to be about 1.5 meters away from the working horizontal line.

There are many models for Outdoor wall lamps, and different models of Outdoor wall lamps have different installation heights.The height of ordinary Outdoor Wall lights should be controlled between 1.7 meters-1.8 meters, and it should also be adjusted according to the actual situation.For example, a Wall lamp with a size of 180mm*160mm model, its installation height should be between 1.4-1.7 meters.The model with a model of 180*350mm, the installation height will be between 2.2 and 2.6 meters.

Method of the installation of Outdoor wall lamps

The Outdoor Wall lamp first needs to connect the wiring of the Wall lamp to use the connection that can be controlled by controlling the switch.The bright application line should be equipped with a pull -line switch and a dark application wiring. You need to choose a dark key switch.In addition, the switch of Outdoor wall lamps needs to ensure whether the operating tissue response of the switch is sensitive and light, and can it instantly achieve the effect of switching at will.

After the position and lighting of the Outdoor Wall lamp are determined, the first thing to install is the work of the Wall lamp. At the beginning, the method of using the embedded parts or punching is fixed.On the wall, try to work first.

precautions for the installation of Outdoor wall lamps

1. Outdoor Wall lights can be installed on the wall or on the pillars.When installed on the brick wall, you must raise wooden bricks or metal components when building walls. When installed lamps, fix the lamps on wooden bricks or metal components.The component may use the hug to fix the metal component on the pillar, and then put the Outdoor Wall lamp directly on the metal component.

2. The height of the bottom along the Outdoor Wall lamp is 1.8m. The height of the Outdoor Wall lamp device on all sides can be different, but the height of the Outdoor Wall lamp on the same wall needs to be common.

3. The structure of Outdoor wall lamps should be adapted to the environment of the device venue. The good choice of a closed switch. Because the Outdoor should often appear in rainy sun and sunburn.

4. Outdoor Wall lights should be selected from the type of switch according to the wiring method.In the open wiring, the pull -line switch should be selected, which is both economical and safe.The dark application line should be dependent on the wiring situation. If the dark wiring in the wall can be selected, the embedded dark key switch can be used.

5. The operation organization of the Outdoor Wall lamp switch should be sensitive and light, and its action is completed by the instantaneous conversion organization.In addition to the pull -line switch and dual -control switch, the connection and disconnection of the contact should be significantly marked.

6, Outdoor Wall lamp line switching lines should be used for insulation ropes, the length is not less than 1.5m, the line tissue and the pull rope should not fail for 1min with 98n force.

Outdoor Wall lamp classification

1. European Wall lamp

The European -style Wall lamp originated in the 1980s, mainly with the representative of the decorative application in the British royal family.It was not recommended to China in the early 1990s.It has not been applied in the domestic decoration industry in the past two years. It is mainly applied to the decorative engineering of star hotels, senior clubs, and villas to reflect the grace and luxury of the European aristocracy.

2. Rural Wall lamp

The entire room reflects a strong humanistic atmosphere, which complements the simplicity and nobleness.It makes the whole room feel very charming.

3. crystal Wall lamp

crystal Wall lights add a little aura to the current simple space, so young people usually prefer crystal wall lamps when buying Lights.Bright and gorgeous crystals give people a solemn and luxurious feeling.

4. Modern Wall lamp

Use a variety of bright flower elements to decorate the spring bedroom, and decorate an elegant arc Wall lamp on the bedside, making the spring bedroom more elegant and romantic.