1. Is it illegal construction?

This depends on where the telescopic Shading shed is built. Construction of telescopic Shading sheds in the community. Then this must be regarded as illegal buildings. Like the community, it must not be able to build a telescopic Shading shed or anti -theft net. After construction, it is built.All need to be demolished according to law. Now the management in the community is very strict.

However, if it is a house built in your own home, you can build a telescopic shade shed. This management will be slightly loose. Of course, it is best to consult with government staff before construction.It can be built so that it is not an illegal building.Of course, the construction of a telescopic shed must not take up additional homesteads.

2. How to install the telescopic Shading shed

1. When installing the telescopic shade shed, we must first measure the width of the door body to determine the installation position of the sunshade and mark it.

2. Next, we drilled on the wall and stuffed the expansion bolts into the hole.

3. In the next step, starting the shade shed fixed parts, such as telescopic arm, etc., we can use bolts to install fixed parts firmly.

4. Finally, we will fix the Shading cloth.

Third, why do I need to install a shade awning

1. It can effectively block the sun, thereby reducing the indoor temperature, reducing the frequency of emptiness, and reaching economic benefits.

2. You can also open the window when using a Tent to keep the indoor circulation in the air. At the same time, you must avoid direct sunlight to destroy indoor furniture.

3. It can develop the Outdoor space so that we can leisure and exercise on the balcony or platform, so that we will not be damaged by ultraviolet rays and harmful substances in the sun.

4. Add some personalized embellishments to the building, decorating home, can also make it more fashionable and artistic.

1. How much is one Square meter in the sun?

The price of the sunrier canopy is available from dozens to hundreds.The price of sunlight plates with different materials is much different. Generally, the price of sunrochemine of the material is 1561 Square meters. Of course, the difference in the material of the material will also be different.The price of PC Sunshine board is not a constant price, but a comprehensive consideration of the technical process level and the performance of the board. At that time, the price and other costs of raw materials and other costs were calculated.

The price of the PC Sunshine board is calculated as follows: 6mm-16mm thickness, and the general price is from 25 yuan to 100 yuan/. The thickness of the thickness of this interval is relatively common.X -shaped, rice type, honeycomb type.The thickness is 16mm-40mm, and the price is generally 80 yuan-2060 yuan/. The PC sunboard with this interval thickness is generally less used, and it is also divided into various shapes.

2. How to install the Sunshine Fragrance

1. First check the skeleton, which must be flat without welding scars and burrs.The skeleton must be completely dry and there must be no volatile solvents.

2. Powder the tan -based waterproof tape on both sides of the skeleton to form a small sink.

3. Place the sunboard on the skeleton, and the telescopic joints are reserved between the board and the plate.

4. Press the EPDM press on the interface between the board and the plate.

5. Fix it with a drilling screw.

6. The skeleton must be used at 1.05m in the middle of the sunboard.

7. The sunlight board on the wall shall not be directly contacted with the wall surface, fix it on the wall with angle aluminum, and then put the sunboard in and install it.

8. The sunblasts are sealing the mouth with aluminum tape first, and then fixing the edge or corner aluminum.

Three, installationSunshine Steakprecautions

1. Check the cutting size of the board and whether the reservation of the bulletin is appropriate. We must pay special attention to leaving enough uniformly swelling gaps. The calculation formula is as follows: Total expansion gap = bulging coefficient*The maximum temperature before and after local installation of local installation*board length.

2. The section of the plate was clamped in the large -scale plate installation engineering must contain at least one tendon rib, or the smallest part of the section of the edge of the board is 20mm.

3. Recognize the surface of the surface of the board, and install the surface out of the outside, and never allow the ultraviolet side to be installed inward.

4. Before installing, the protective film surrounded by the plate is 30mm-50mm. Do not clamp the protective film of the profile, but you should not remove too much, so as not to damage the board due to operation.

5. When the self -attacking nail is tightened, the force should be evenly tightened to ensure that the type plate is truly crushed and densely sealed.

6. In the case of cold bending of hollow plates, its curved radius must not be 175 times the thickness of the analytical material.

7. The hollow plate can only bend the ribs in the direction of the ribs.

8. The tilt installation of hollow plates should be directed to the ribs, which is conducive to the export of condensation water.

How to install an electric car sunshade

1. Prepare a wrench in advance to confirm that the electric vehicle sunshade shed is complete and non -damaged, and the accessories are not omitted.

2. Understand the hexagonal screws of the rearview mirror with a wrench, remove the two rearview mirrors, place the connecting rod of the sunshade between the rearview mirror and the electric car body, and twist the rearview mirror.

3. Insert the two sleeves in the front of the sunshade into the connector, be sure to insert it to the end, so it is very tight.

4. Pull the back of the sunshade to the rear box of the electric vehicle, and tie them on the electric car body on both sides with ropes. If you want the position of the ripkin, you can also tie it to the back of the rear box.

5. At this time, there are four elastic rods in the remaining accessories. The two thicker and rigid ones are reinforced on the top of the shed, which are connected respectively.

6. The other two long and soft elastic rods are supported by the side of the rails, which are connected separately to complete the installation.

What should I pay attention to when installing an electric vehicle sunshade

1. Be sure to reserve the expansion space, the screw spacing, which can be made according to the thickness of the board. It is too small and too large.If the spacing is too small, sometimes it will cause stress due to too tightly, causing damage; if the spacing is too large, the PC board may not be unstable.

2. The plasticizer in the PVC cushion and the chemicals in certain rubber pads will be migrated to the surface of the cushion. After contacting the PC board, the PC board will be destroyed, so it is absolutely not available.It is recommended to use the material of the cushion, the product of the Sanyangi Copycopar, silicone rubber and chlorine rubber.If there is no suitable padding, it is better not to use it, nor can it be used to destroy the pad of PC.

3. In addition to the waterproofing, the double -sided waterproof tape can also be used for the pad material between the PC board and the frame.Some double -sided tapes are damaged in the face of PC boards, so they are also selected during installation.

4. PC boards are very easy to scratch. Do not tear the protective film when installing.Before cutting, the marker must be marked and marked as much as possible on the protective film. If it must be marked directly on the plate, please use a crayon to avoid using sharp tools to contact.

1. Where is the application of sunrs?

Shame sheds are generally used in villas, duplex houses, jumping houses, roofs, bottom floors, podiums, hotels, hotels, clubs, cafes, sun rooms, public places and other places. In recent yearsUse.Especially villas, windows and doors, there are some Outdoor sunshade sheds.The amount of usage on the top of the building is also very large, and the effect of the roof sunshade is more obvious on the shelter of the building.

People who use shade pings are generally home owners, decorative companies, people who have ideas for architecture, garden design, Sunshine house companies, national organs, building design institutes, real estate developers, designers teams, catering industry, hotels, etc.industry.In fact, the scope of application of sunshade has a lot of applications. More and more people pay attention to the shelter, and continue to improve the shade shed, so that the sunshade can adapt to more environments.

Now in some large gymnasiums, opera houses and other places, there are shadows of membrane structures. Many famous buildings in the world have used sunshine.With the development of technology and craftsmanship, the scope of the use of sunshade will become more and more colorful to people's lives.

2. How to install a sunshade

1. Before installing a sunny shed, the ground distance should be measured, the location you need to install, and the thickness of the wall, etc., to ensure the construction environment of the sunshade and formulate the installation plan.

2. You need to punch holes on the wall. The size of the shade shed is the distance of the hole distance. It is necessary to accurately measure, otherwise it will affect the use effect.If it is a high -altitude operation, the protective net needs to be installed, and the operators should take safety measures.

3. The sunshade needs to fix the bracket and the splint when installing, and the distance between the splint cannot be greater than two meters.Because if it is too large, it will cause the bracket to be unstable, and at the same time, the various nuts and bolts on the splint need to be fixed.

4. The last step is to fix the screws of the shade shed, and in order to facilitate fixation, the spinal rope is also required during the installation process to prevent shaking.

3. What do you need to pay attention to when you use the sunshade

1. When charging the season, you need to check the various parts, and the hardware such as the buttons, the handle, and the knob should be coated with lubricating oil for maintenance and maintenance.

2. In the drying state of the Shading shed, use a soft brush to clean the dust, but do not use corrosive chemical cleaners, such as acidic or grinding cleaning tools to avoid damage to the surface.

3. After cleaning and cleaning, wait for it to completely dry before you can put or close.