Solar street light installation method to install solar lighting street lights should be paid attention to
1. Solar street light installation method
Solar street lights have the advantages of good stability, long life, high luminous efficiency, easy installation and maintenance, high safety performance, energy saving and environmental protection, economic and practical, etc. It is widely used in the field of public power lighting. So how to install Solar street lights?
1. Pour the foundation
(1) Establish the installation location, and according to the construction drawings and the geology of the survey site, there is no shade at the top of the street light, and the lamp spacing is 40 meters as the benchmark to determine the installation location of Solar street lights.
(2) Digging road lamp foundation pit, excavate the lamp base pit in the installation location, and pay attention to confirming and protecting other facilities such as cables, pipelines and other facilities in the excavated location when digging the foundation pit.
(3) Burn the battery and build a battery box in the dug foundation pit and bury the battery box into it.
(4) Basic embedded parts of the pouring street lights, place the embedded parts of the Solar street lights into the pit, put one end of the wire Tube in the middle of the embedded parts, and the other end is placed at the buried battery.And keep the embedded parts, foundation, and ground on the same horizontal plane, and use C20 concrete to fix the embedded parts.
(5) After the construction is completed, clean up the residue on the positioning board in time. After the concrete is solidified, the Solar street lights are installed.
2. The installation method of Solar street light components
(1) Install Solar panels: Put the Solar panel on the battery plate bracket, tighten it with a screw, connect the output line of the Solar panel, pay attention to connect the positive and negative pole of the correct battery board, and use the output line of the battery plate to use it with tie the battery board.Turn it in a firm, tinten tinten on the battery panel wiring, and then put it aside to wait for the thread.
(2) Install LED lamps: Put the light line out of the light arm, leave a lamp line at one end of the installation head; support the light pole and wear the other end of the light line from the slide hole reserved by the light rod.Out, install the light line to one end of the top of the light pole; install the lamp head at the other end of the light line, align the screw holes on the light arm and the light rod, and then tighten the light arm with a quickly wrench;Put on the top of the top of the light rod to make a mark. Together with the Solar panel thread wiring, put the two wires together on the bottom of the light rod with a thin thread Tube, and fix the Solar panel on the light rod.
(3) Lantern rod Hanging: After checking the fixed conditions of each component, put the sling rope in the appropriate position of the light rod, slowly roll up the lamps, and when the light rod is lifted to the front of the base, slowly put down the light pole and rotate the light pole at the same time.Adjust the lamp head to the pavement, and the holes on the flange plate are aimed at the foot bolts; after the flange plate falls on the foundation, put the flat pad, spring pad, and nuts in turn, and tighten the nut with a wrench to fix the light pole.
(4) Install the battery and controller: Put the battery in the battery shaft and put the battery thread on the road base with fine iron; then connect the connection line to the controller, first connect to the battery, then the load, and then connect to the Solar board; debugging; debugging;Whether the street light work is normal. If it is normal, set the controller mode to make the street light light up. If there is no problem, you can seal the lamp cover of the light rod.
3. Component adjustment and secondary embedding
After the installation of Solar street lights is completed, check the installation effect of the overall street lights, re -adjust the light rods, and check whether the rising angle of the battery board is deviated, whether the light head is legitimate, etc.;The base is embedded in a secondary embedding, and the base of the light rod is made into a small Square with a cement to make the Solar street light more firm and reliable.
2. What should you pay attention to when installing Solar lighting street lights
Solar lighting street lights can save energy and relieve energy consumption. It is a very practical type of new street lights. However, when installing Solar street lights, you should also pay attention to some aspects, such as:
1. installation location
Try to avoid installation in the low -lying road sections of the road. Pay attention to whether the installation location is to fill the soil when pouring. If it is backfill, the basic pit should be deepened and increased, so as to ensure the stability of the later use of Solar street lights.
2. installation time
The installation of Solar street lights should be installed on a sunny day. If it is installed on a rainy day, it will not be able to meet the design requirements after the light consumes power and does not charge it. Also, try not to light up the Lights on the day of the installation.After the electricity, the load is connected in the evening.
3. The angle of the battery board
The brackets of Solar panels are generally made before the factory. As long as you ensure that you can facing the south and ensure that there is no obscuration around, if the deviation is large, you may need to be adjusted.
4. Pay attention to wiring
Solar street lights are low -voltage systems. When wiring, it is mainly to distinguish between positive and negative electrodes. After determining the positive and negative electrode of the battery plate, light source, and battery, it is necessary to strictly follow the wiring description of the controller.