1. What are the benefits of electric scissors to pruning fruit trees

Electric branches and scissors are a kind of efficient, ecological, safe electric branches and scissors. They can cut fruit branches such as apple branches, grape branches, mulberry branches.Good helper for production.The advantages of electric scissors are mainly:

1. More efficiency

Electric scissors are powered by electricity. Its pruning efficiency is 2 to 3 times that of traditional hand -cutting efficiency, and electric scissors can also be trimmed in both directions. It is more suitable for trimming or shape than ordinary scissors.And in the past, it was unbearable to use manual scissors to trim fruit branches for a long time and arms, while electric scissors would not have this situation.

2. Good durability

The supporting structure of the electric scissors is simple, the operation is stable, the failure rate is low, the blade cutting capacity and life are high, and it can be used for a long time under normal use and regular adjustment.

3. High pruning quality

The performance of electric scissors is stable, and the quality can meet the requirements of Gardening. Under the correct operation, the flatness of the fluff surface is better than manual trimming, and there is basically no leakage.Compared with manual scissors, the fruit branches that are trimmed by electric scissors are closer to the natural growth state. The canned crown surface is larger. The trimmed surface is neat and beautiful, and the buds and leaves are sprouting and sprouting.

4. Good safety protection

Electric scissors have a good safety protection function. The blade follows the wrench. When the stuck is stuck, the circuit self -inspection process will start motor monitoring, and protect the motor without burning.The protection function of both sides of the motor (DC -free motor) is controlled by Hall chip switch.Rewarding the trigger position will open the cuttings and then close.The stress of the battery over loading is overheated and over -discharged and the discharge will be maintained by the protection of the circuit board.

2. What should be paid attention to when the use of electric pruning is trimming

With the development of technology, electric pruning has become an indispensable Tool for garden operations. Electric branches and scissors are not only more laborious when the method is wrong, but also may affect the service life of electric pruning.Pay attention to some matters:

1. When using electric pruning trimming and accessories, we must comply with the instructions and use methods of use. At the same time, the working environment and the work they want to complete should be considered. The use of electric pruning and trimming as a operation that does not meet the requirements may cause danger.

2. Electric pruning pruning requires professional training to use, so that the unfamiliar electric pruning trim or those who do not understand the use instructions are very dangerous to use without training.

3. Do not cut the branches of the working range of the scissors. Do not cut too hard things such as metal, stone and other non -plant materials. Do not clamp the Tool with tiger clamps. If scissors are worn or damaged, please replace the scissors.

4. Electric branches should be kept clean before and after use. After use, use clean cloth to clean electric branches, batteries and chargers, and use soft brushes or dry cloths to clean the dust on the scissors head. Do not use it. Do not use it.Any corrosive or solvents cleaner.

5. Use the equipment correctly according to the instructions of the use. Do not use electric branches, batteries, and chargers. Do not use electric branches, batteries, and chargers in any liquid.

6. Make sure that the switch is closed when adjusting, replacing attachments or storing electric branches, and avoids the risk of electric branches and cutting unexpectedly.

7. The idle electric pruning is trimmed in the blade closure and stored outside the child.

8. After use, the dirt should be removed first, and then the dirt should be removed first, and then the lubricating oil or oil is lubricated on the contact part, so that the blade is in a normal maintenance state. This can reduce the resistance and extend the life of the blade.

[Family Flower seeds] Frequent flower seeds planting methods how to germinate flowers

1. Methods of common flower seeds

Rose

From April to June, the choice of soil: Rose seeds are low, so the soil for sowing needs to be loose, breathable, and high water holdings.The soil used is mixed with vermiculite, peat, water moss, perlite, snake wood chips, etc. If possible, configure it yourself; there is no conditional general weakly acidic soil, but there must be no foreign objects in the soil (such as such as such as foreign objects (such as such as such as such as such as: Stone broken brick glass, etc.) or choose sand soil. First refrigerate the rose seeds for about 15 days, soak it in warm water at about 40 degrees after refrigerating, continue to soak for 4-6 hours after the water cools, remove the seeds, remove the seeds, soak it after soakingSeeds are easy to germinate.

Step 2: Put the seeds in the soil, which can be broadcast 5 ~ 8 capsules in each container.After germination, a strong seedlings are leaving a strong ones; after germination, one to 3 small seedlings are left as appropriate.After sowing, cover the plastic wrap on the container (convenient for the plastic film of the bag), and the plastic wrapSpread a few small holes in breathable.Put the container in the sun and keep the temperature about 20 degrees.Most seeds can germinate 15-25 days.After germination, wait for the seedlings to thrive and transplant them into the ground.

Jasmine

Before sowing more, it is necessary to soak the seeds for 12 hours, which can promote the neat and fast seedlings.The on -demand acupoint is 3 cm 5 cm, and the thickness of the soil is about 2 cm.The seedlings must prevent drought during the seedling period, and water once every 3-5 days.It is more suitable for planting in May, setting the dewly flower bed or the pot.

Lily

Lily is gorgeous, but it belongs to novice flowers. After planting, basically do not need to control it. Water drying, just do it!Of course, you should remind the flower buddy here. Do nt think about watering every day.Just water the water! After the lily (can also cut the flowers), continue to be maintained normally. In winter, the rod will naturally wither, and the ball does not need to be dug out.Gel, occasionally give water in winter.

Tulip

planting plants in the sandy loam soil that is drained in the sun, and the plant can be considered when the soil temperature is below 12 C below 12 C.After deep cultivation, Fertilizer should be applied, and the ball is covered with soil to cover the soil. Watering is no longer watered after the soil is covered, but the grass must be covered to improve the humidity of the soil and prevent the soil plate.Before the young buds were unearthed, they were applied once, and the Fertilizer concentration was increased after the bud (10%Fertilizer 90%water).During the growth period, it is generally not watered or less watering. As long as the soil is moist, if the weather is dry, it can be poured 1 or 2 times the water transmittance (about 15 cm in damp depth).As used for cutting flowers, cutting should be cut when the flower buds are completely changed, and the viewing period of bottle insertion should be about 10 days.

First, dilute the polymorrhrophopsy (about a bowl of water), stir well, soak the wind and let it be soaked in about 1 hour, then remove it with a napkin and dry it, and dry it in the ventilation.Then add tap water to the dedicated bottle, about to the bottleneck, drip 4-5 drops of nutrient solution in the water, and then place the ball on the bottle. Note that when the ball is placed, the water is optimistic.On the top, you can only get the root plate under the ball. If there is more water, you can pour it a little. If the water is less, you can add it.Pour this newspaper or carton, and you can withdraw from about 5 cm and you can withdraw.So you just wait for the beautiful flowers.

Gorin lotus

First use water to soak the dry golden lotus seeds for 24 hours, and the water at room temperature is fine. After the seeds are soaked, use a small plastic box, two layers of paper towels below, spray wet, put the seeds on, and then cover a layer of paper towels.Also wet, cover the lid, and start germination.Because there is heating in the house, the room temperature is above 20 degrees, so about 3 days, there are seed dew.The so -called "dew" is a white bud that extends the seeds. In fact, this is its root.The seeds of dew can be planted into the soil and enter the seedling stage.Seedlings can be raised with small Flower pots, soil for seedling (to raise potted drought golden lotus, one must choose a reasonable cultivation soil), you can use a typical "three -in -soil", grass charcoal: perlite: vermiculite = 1: 1: 1: 1: 1. Generally speaking, 8-12 days can sprout and break the soil.

Lantern flower (inverted golden bell)

Sowing time: spring or autumn sowing, sowing method: 1 to 3 capsules per point, 7 to 14 days of germination of 7 to 14 days of 15 ~ 22 degrees Celsius.Use vermiculite or medium after broadcast.Keep the medium a little wet, but avoid excessive water.Transplantation: 4 to 6 weeks after sowing.There are 1 pot of 10 to 15cm pots, while large containers are 2 to 3 per pot.Light: Chang Rizhao Plants.Long Rizhao is conducive to flowering.Fertilization: High degree of Fertilizer.Add mild release Fertilizer to the cultivation medium, and apply medium -concentration liquid Fertilizer once a week.The germination rate is very low, there must be courage to plant, try a few more times!

Yu Meiren

Light light, cool and cool, avoid high temperature, winter warm and cool in the summer is most suitable for growing. The growth period requires sufficient light. At least 4 hours of direct sunlight every day.If the growth environment is dark, the light is insufficient, the plant grows thin and the color is dim.Summitted from September to October in the pre -organized seedbed. The germination temperature is 20 ~ c. Because the seeds are very small, the seedbed soil must be thin, the soil is not covered after sowing, the grass is wet, and the cover is unveiled.The seeds of Yu Meiren are easy to scatter. After one year of planting, the environment will no longer be sown, and there will be countless small seedlings in place.Watering should not be too much.

Second, flower seed germination method

Due to the different aspects of seed structure and physiological mechanism, different types of flower seeds have different germination periods.Some seeds are sowed in time, and they can germinate seedlings soon, while some seeds take several months or even years to germinate. Therefore, it is necessary to achieve artificial germination by shortening the dormant period of the seeds.

Temperature and humidity are the key factor affecting the germination of flower seeds, so you can control the dormant period of flower seeds by regulating these two conditions.Including the following methods:

1. Water immersion: Bauhinia, pearl plums, brocade flowers and other flower seeds have a short dormancy period and easy to germinate. Generally, they only need to soak the seeds in 40 C, and can be directly sowed for 1 to 2 days.Torch trees, such as torch trees, soak the seeds with difficulty germination, soak them with water at 90 C for about half an hour, and then cool down naturally for 1 day. This can soften, absorb water, and germinate.During the process of water soaking, pay attention to changing the water diligently, and control the water temperature and soaking period in a suitable range to avoid the death of embryo.

2. Low temperature: You can mix the seeds with 60%of the seeds and humidity, then put it in a plastic bag, tie the bag, put it in the Flower pot, and then bury the Flower pot into the open field of 40 to 60 cm deep.Or put the seeds in the refrigerator for 2-3 months, keep the temperature at 3 C to 5 C, and then sow.It can also be frozen to frozen the seeds naturally through low -temperature Outdoor Outdoor temperature, and it can be unearthed in the spring of the next year.Such methods are suitable for pear, plums, cloves and some autumn herbs.

3. Warm change: For flowers seeds with embryonic roots and embryo axis dormant habits, the seeds of the streaming, peony, and peony, the seeds need to be mixed with the wet sand, and then the high temperature and low temperature treatment after a certain period of time.germination.In order to break the dormant period, the embryo root generally requires a high temperature of 25 C to 32 C, and the duration is maintained at 1 to 2 months or more, and the embryo shaft requires a low temperature of 3 C to 5 C, and the length is maintained for 1 to 3 months.

Recommended reading

[Method of Family Flower] The most practical family flower breeding skills of novice flowering flowers and getting started

[Novice Getting started] What kind of flowers are suitable for novices to raiseIntroduction to newbies

[Family Flower Basin] What kind of choice and techniques of Flower pots are good for Flower pots

[Family Flower Flower Soil] What kind of soil is suitable for farming family flowers and soil.

[Family Flower Flower Fat] How does family flowers make flowers and fat Family Flower Flower Flower Fed

[Family flowers and watering] How long does it take for flowers to grow flowers and flowers?

[Family Flower flowers and Worms] How to remove flowers in the Flower pot in the family with flowers in the family

[Family flowers do not bloom] What should I do if the flowers are not blooming?

[Family Flower Flower skills] How to raise flowers to raise flowers and cultivation skills and methods

[Four Seasons Nourishing flowers] What are the precautions for family breeding of flowers in the four seasons of the family?

[Family Flower Flower tools] What are the essential small tools for flowers in common flower farming tools

1. What are the benefits of sustaining flowers

For many flowers, perlite is no stranger.But do you know what kind of effect is for flowers to grow flowers?

1. Improve the knot of the soil and improve the breathability

The interior of the perlite is full of air holes, just like a small "ventilation".After mixing these stomators with the soil, it can effectively improve the drainage and breathability of the soil.Imagine that the roots of plants are freely breathing in these small holes, and nutrients can be better absorbed.This is very important for the healthy growth of flowers!

2. Water absorption ability, water preservation and Fertilizer

The water absorption ability of perlite is also bars!Its internal hole structure can absorb a lot of water, and can even reach 2-3 times its weight.In this way, even in a dry environment, plants can get stable water supply.Moreover, perlite can also absorb and store effective ingredients in Fertilizer to ensure that the nutrients required by plants in the process of growth are continuously supplemented.

3. Absorb pesticides and play a dilution role

In addition to improving the soil and water preservation and Fertilizer, there is a special function of perlite -absorb pesticides.Its porous structure can effectively absorb pesticides and play a role in dilution and slow release.This is especially important in family Gardening, because the use of pesticides may cause pollution to the environment.The adsorption effect of perlite can reduce the risk of pollution and protect the environment of the environment and the health of flowers.

Second, the correct way to use perlite seed flowers

Sleeve is a common cultivation medium that is widely used in flower planting due to its good breathability and drainage.Here are some key steps to use perlite flowers to ensure the healthy growth of flowers:

1. Prepare suction

Choose pure perlite to avoid using varieties containing impurities.Pour the perlite into the Flower pot to ensure that the thickness is appropriate.

2. Add Fertilizer

Add an appropriate amount of Fertilizer to the perlite to provide the nutrition required for flowers.Pay attention to control the amount of Fertilizers to avoid excessive causes of burning.

3. Watering

Use the appropriate amount of water to pour flowers to ensure that the perlite is kept moist.Avoid excessive watering to avoid rotting roots.

4. Light

Provide appropriate light conditions according to the needs of different flowers.Make sure flowers accept sufficient sunlight or appropriate scattered light to meet the needs of photosynthesis.

5. ventilation

Maintain good ventilation conditions and help the healthy growth of flowers.Wind open windows regularly to avoid flowers in a closed environment.

6. Prevention and treatment of diseases and insect pests

Regularly check whether the flowers have signs of pests and diseases, and take prevention measures in a timely manner.Proper pesticides can be sprayed to prevent and treat diseases and insect pests.

Follow the above steps. The use of perlite flowers can provide a good growth environment to promote the growth of flowers.

Third, precautions for suction flowers

1. Plant selection

Plane is an acidic matrix. When nourishing flowers with perlite, it is best to raise flowers that like acidic soil, which can promote these flowers to grow better. If the substrate for flowers that like alkaline soil, it may reduce the flowers of flowers.Observation value may even cause withering.

The perlite matrix is relatively frivolous. Mixing it into other soil can also improve the breathable drainability of the soil. Therefore, it is very suitable for drought -tolerant and waterlogging plants, and it is not suitable for plants that grow in humid environment.

2. Soil mix and match

Square is a non -toxic and tasteless matrix, but the acidity of perlite is relatively high. Usually use perlite to pay attention to mix and match the perlite with other soils.Growing in the rock.

3. It should not be excessive

Plane is an acidic lava erupted from volcanic, which is helpful for many flowers, but it should not be excessive when mixed with other soils. It can be mixed with perlite at a ratio of 4: 1.

4. Wind -proof Running away

In fact, perlite is easy to be powdered. Usually when we use the perlite to make flowers, each time we water the flowers, the surface of the perlite will surface.The rock can be run away by the wind.

5. Anti -proof in the body

Although there is no toxin in perlite, after the pink powder is powder, it is easy to be blown into the air by the wind. If people absorb them into their bodies, they will cause some harm to their health. Therefore, Be careful to avoid absorbing it into the body.

What are the breeding tools for family balconies?

1. Tieshai

Used for moving vegetable seedlings and shovel.There is no need to be iron, and plastic is also available, but try to prepare one as much as possible, otherwise, do you have to use your hands when shovel?

2. scissors

The scissors mentioned here are preferably horticultural cuts, which can cut pruning, scissors, and thick stems.Can be used for seedlings and harvest fruits.

3. kettle

A kettle specially poured with a kettle shower, try to choose the kettle according to the size of the plant planting plants, then the large pot is large, and the planting area is small.

4, hemp rope

There is a little bit of the house to bind and guide the growth of the stems.

5.

If you plant some rattan plants at home, you need this support pole to support it.

6. Potting bottom net

The closed and poor ventilation balcony must be prepared.Putting the net at the bottom of the container can prevent the soil flow from flowing out and the invasion of the pests.

7, small can

Generally made of plastic, just a little bit.If not, you can use a paper cup instead.

8. grid frame

Although this looks a bit weird, it is very practical!It is a tunnel bracket on the vegetable basin to support gauze.Cover the gauze on it and fix it with a clothes clip.The gauze can be removed at any time, which is very convenient.This Tool can prevent insects, birds, and excessive light. It is best to choose white transparent.

9, table, bamboo board

You can put the vegetable basin in a higher place to make it more fully accepting the sun, and it will also make the balcony more three -dimensional.In order to prevent moisture, it can also cover the excessive sunshine in summer.If the quality of life is not so high, you can use a small bench instead.

10. Sowing spoon

Sowing a spoon has become simpler to sow the difficulty.He can simply plant small spoons with small seeds, with small concave pits of 1.2 mm, 2 mm, 4 mm, and 1.5 mm (ellipse), which can be placed on a grain of seeds for sowing.Size: 1 cm wide (spoon), 16.5 cm long.

11. Plastic mesh cover

Plastic mesh covers are generally given to Flower pots or protective plants to prevent diseases and insect disasters of some plants.

Profile

Hawaii coconut, also known as bamboo stem pocket coconut, Chevrole coconut, is a pocket coconut, also known as green stems, brown brown, root brown, heavy Buddha coconut, bamboo stems and exquisite coconuts.Hawaii coconut is distributed in Mexico, Borz, Guatemala and Honduras.Hawaiian coconut sex is high -temperature, high -humidity, yin resistance, afraid of direct sunlight; strong adaptability to the soil, but it is suitable for loose, humid, and drainage. It is advisable to have deep soil soil.Not only is the plants beautiful, but also easy to bloom seeds. The appearance of the branches and leaves is dense, the leaves are green, and the leaves are full of luster. The feathers are elegant, giving people a dignified, elegant, and beautiful beauty.The leaf and stems are conducive to purifying the air and beautifying the environment.

Nickname

bamboo stems, exquisite coconut, bamboo, bamboo coconut, Chevrole coconut

Morphology

The stems of the Nagatai coconut stems are upright, with a height of 1-3 meters.The stems are short, hollow, and the new buds of the stolons of the underground stolons are pumaging new branches, which grows in cluster without branches.The leaves are mostly the middle and upper part of the stems of the stems, which are full of feather -like cracks.The flowers are the inflorescence of the meat, and the axillary is born on the upper part of the stems, pink.Purple red.The fruiting period can be up to 2-3 months.

Suitable place

Hawaiian coconut leaves are dense and green, with thick leaves and luster. The feathers are elegant, giving people a dignified, elegant, and beautiful beauty, becoming a rookie for indoor leaf plants.It is extremely resistant to negative and is suitable for indoor cultivation and viewing. It can be used for greening decorations in the living room, study room, conference room, office, and other places.

Effectiveness and role

Regulate humidity

Hawaiian coconut has the function of regulating humidity. Especially when the indoor humidity is low in winter, as long as it is regularly watered by it, Hawaii coconut can keep the indoor humidity in a state of 40%to 60%.

Purify the air

The ability of Xiawei coconut to remove benzene, vinyl chloride, formaldehyde and other toxic gases is very capable. It is an ideal plant in purifying indoor air.

Family decoration

Hawaiian coconut is suitable for placing in a spacious space.Hawaiian coconut does not grow outward, giving people a straight and straight feeling, it is the best partner of bamboo or wooden furniture.It is easy to take care of it, green oil, strong vitality, without watering for a few days, it is not easy to turn yellow. Unlike other plants, it will fade without watering for a day.The leaves will not fall easily. Even if a leaf is going to fall, it must be corrupted for a long time to become yellow leaves, and then slowly fall into the place. Although it is corrupt, it will not be ugly.

Breeding method

illumination

Although Hawaiian coconut grows in a relatively warm place, this plant itself is not resistant to direct sunlight. It is more suitable for growing in a half -yin environment.It affects plants.Therefore, when lighting is usually made, it cannot be directly illuminated by strong light, otherwise it will affect the leaves.

Humidity/watering

Hawaii coconut is more suitable for humid environments, especially when it grows, it must be given enough water to make the pot soil moist.Although it likes to be humid, it can't be too wet, otherwise it will let its roots fester.Then in winter, watering should be controlled to keep the pot soil dry, but it should not be too dry, otherwise the leaves will become no shiny.

temperature

Hawaiian coconut was originally living in a warm place, so it prefers to grow in a warm place. The most suitable temperature is 20 degrees.In winter, the temperature should be maintained above 10 to not affect growth.Of course, it also has a little cold resistance, but it can only endure a low -time low temperature in a short time, so if you want it to go through the winter smoothly, it is best to adjust the temperature above 10 degrees.Maintain above 5 degrees.

soil

It generally prefers to grow in loose and fertile soil, so it must meet this requirement when choosing the soil.We can use some humus soil and garden soil, etc., mix them together, and then add some organic Fertilizers to mix well, we can be used as the cultivation substrate.

Fertilize

In the growth period of Hawaiian coconut, it needs to be applied to nitrogen fertilizer once a month, and then in September, it needs to stop applying nitrogen fertilizer. Just add phosphate Fertilizer once or twice to help it go smoothly.Then it will stop applying any Fertilizer in winter.

prune

Generally, you only need to cut off the leaves of the yellow disease, or only cut the tip of the leaves.When cutting the leaf, pay attention. If the leaf sheath becomes yellow, it must be peeled together. If it is not yellow, it can be peeled when it needs to be yellow, otherwise it will easily hurt the stems!

Frequently problem handling

Breeding method

Hawaii coconut can be sowed and divided into breeding.

seed seeds should be sowed with them, and germinated at about 3-4 months when the temperature is 25 C.

During the growth process, the underground roots can be extended horizontally and can adhere to the new buds and new branches. Therefore, in spring, the dense growing plants can be cut into breeding, and a new cluster contains 3-5 roots.When cutting, pay attention to less damage to the roots and keep each bus a certain root system, otherwise the recovery will be slow or even affecting survival.

Cultivation technology

Hawaii coconut can be sowed and divided into breeding.seed seeds should be sowed with them, and germinated at about 3-4 months when the temperature is 25 C.During the growth process, the underground roots can be extended horizontally and can adhere to the new buds and new branches. Therefore, the dense growing plants can be cut and reproduced in spring, and a new plant is planted with a cluster of 3-5 roots.When cutting, pay attention to less damage to the roots and keep each bus a certain root system, otherwise the recovery will be slow or even affecting survival.

Hawaiian coconut pots can be directly used in white plastic pots (or mud pots, plastic white plastic pots).It is advisable to use loose, good ventilation and water -rich matrix. Generally, it can be mixed with corruption soil, garden soil, and river sand.From March to October of the growth season, liquid Fertilizer or granular Compound fertilizer is applied every 1-2 weeks to promote leaf growth and thick leaves.The plant is exchanged for two years to 3 years.Following the rotten cake Fertilizer (such as sesame oil cakes, bean cakes, etc.), or poured with soaked cake Fertilizers, Compound fertilizer can also be used.Each fertilization before and after flowering, the water supply should be paid attention to.

The temperature requirements are 10 C.Cold resistance, its growth temperature is 20 C to 30 C, and it is not lower than 2 C in winter.During the growing period, it is required to keep the pot soil moisturizing. When the air is dry, the leaves should be sprayed often to improve the environment of the environment.Keep the pot soil wet and not dry to enhance the cold and wintering ability of plants.

Shawai's coconut growth requires brighter scattered light. To avoid direct light, otherwise the lobel color becomes lighter or yellow; strong negatives can grow in a darker environment in the indoor light for a long time.Generally, it will not have much impact on plant viewing for 1-2 months in the dark environment of the indoor.Avoid strong light. When placed outdoors in summer, it should be appropriately shaded.Yin resistance can be placed in any room in the three seasons of spring, summer and autumn, and placed in the sun in winter.

Under the conditions of high temperature and high humidity, brown spot disease and creammium disease may occur in Hawaii coconuts. This can be sprayed and killed with fungicide (such as multi -bacterial spirit or 1000 times liquid).

summer management

1. In the summer, it should be placed in a place where the sunlight is not shining outdoors, and the sun should be placed in the room in winter.

2. Change the water once a week in summer, and push it for one week in order in other seasons. The tap water should be placed for 10 hours or used in the sun for 2 hours.

3. Put 1-2 drops of nutrients at the same time.

4. The leaf surface spray more than 2 times a day to maintain the humidity and water of the leaf surface.

5. Pay attention to keep indoor ventilation.

6. If the rotten roots appear, just cut off the rotten roots and replace it with clean water.

What to do if the leaves are yellow

1. Fertilizer discomfort

When cultivating it, we all choose some rotten soil, river sand soil, etc., and then mix them with a small amount of organic Fertilizers to configure them into medium.This will be easier to survive in the early stage.Then wait for the 3rd to October each year, and apply liquid Fertilizer once every 2 weeks, so that the leaf color can be stronger. If the above are not done, then its nutrition is not available.The yellow leaves are also inevitable.Therefore, fertilization is also appropriate.

2. Humidity discomfort

When it grows, it is necessary to keep the soil moist frequently, and the air will not be too dry, otherwise the humidity will be reduced, so that the leaves will become non -gloss or even yellow.When the air is dry, we often spray water on its blades to increase the humidity of the air, so that its leaves can be thick and green.It can be seen that humidity is also a reason for the color of the blade.

3. Light discomfort

It is very afraid of strong light. If you accidentally let it be irradiated with strong light, the leaves will make the leaves yellow.It generally prefers the semi -yin environment, and it has a long time to resist, and it is okay even if it is staying in a dark place for 1 to 2 months.So when it is usually maintained by it, if it really gives it too much to the sun, it can only accept some bright scattered light.

4. Watering discomfort

Although its humid environment, it cannot make the water too sufficient, otherwise it will make the pot soil too humid, cause the root ulceration, the nutritional transmission of the plant, and then make the leaves yellow.Therefore, watering must be appropriate to keep the leaves green.

5. Causes of disease

When the temperature is extremely high and the humidity is extremely high, it will prone to some diseases. These diseases will directly affect its plants, so that it can not grow normally, and it will lack nutrition and cause the leaves to yellow.It is necessary to discover timely prevention and treatment in time to prevent the leaves from being harmed.

precautions

1. Xiawaii's coconut pot plant can be directly used in white plastic pots (or mud pots, plastic white plastic pots).It is advisable to use loose, good ventilation, and humus -containing substrate. Generally, it can be mixed with corruption soil, garden soil, and river sand.From March to October of the growth season, liquid Fertilizer or granular Compound fertilizer is applied every 1-2 weeks to promote leaf growth and thick leaves.The plant is exchanged for two years to 3 years.Following the rotten cake Fertilizer (such as sesame oil cakes, bean cakes, etc.), or poured with soaked cake Fertilizers, Compound fertilizer can also be used.Each fertilization before and after flowering, the water supply should be paid attention to.

2,The temperature requirements are 10 C.Cold resistance, its growth temperature is 20 C to 30 C, and it is not lower than 2 C in winter.During the growing period, it is required to keep the pot soil moisturizing. When the air is dry, the leaves should be sprayed often to improve the environment of the environment.Keep the pot soil wet and not dry to enhance the cold and wintering ability of plants.

3. Avoid strong light.Shawai's coconut growth requires brighter scattered light. To avoid direct light, otherwise the lobel color becomes lighter or yellow; strong negatives can grow in a darker environment in the indoor light for a long time.Generally, it will not have much impact on plant viewing for 1-2 months in the dark environment of the indoor.When placing outdoors in summer, it should be appropriately shaded.Yin resistance can be placed in any room in the three seasons of spring, summer and autumn, and placed in the sun in winter.

4,Under the conditions of high temperature and high humidity, brown spot disease and creammium disease may occur in Hawaii coconuts. This can be sprayed and killed with fungicide (such as multi -bacterial spirit or 1000 times liquid).