Wall lamp daily cleaning method

1. The Wall lamp is easy to accumulate dust, and regular dust removal can be maintained to maintain good lighting effect.You can wipe it with a wet cloth, keep the action in the same direction, do not rub it back and forth, and the strength should be moderate.Turn off the Lights inside the cleaning light and remove the bulb.

2. Inside the Wall lights, when cleaning the bulb, first turn off the Lights, and you can remove the Light bulb and wipe it separately when wiping.If you clean it directly on the lamp, do not rotate the Light bulb in clockwise to avoid tightly peeling the lamp head.

How to clean different material wall lamps

1. Cloth lampshade

Wash the fabric lampshade with a soft brush, you can remove the fabric lampshade, and stick to the cleaning agent with a lower concentration on the soft brush, and then scrub the dust on the fabric lampshade. This method is not only simple, but also the wall lampshade.No damage.

2. fruits glass lampshade

Use a soft cloth suitable for cleaning the glass, be careful of the lampshade of the wall, or scrub it with a soft cloth dipped with a toothpaste. You can use a soft cloth to wrap chopsticks or toothpicks.

3. Resin lampshade

It can be cleaned with chemical fibrous tweezers or dedicated tweezers. After cleaning, anti -static spray should be sprayed, because the Wall lights of the resin material are prone to static electricity.

4. Fold lampshade

The fold lampshade Wall lamp can be scrubbed with a cotton swab dipped in water. If it is particularly dirty, a neutral cleaner can be used.

5. crystal beaded lampshade

crystal beaded wall lamps are delicate and exquisite, and clean is very troublesome.If the lampshade is made of crystal beads and metals, it can be cleaned directly with neutral detergent.After cleaning, dry the surface of the surface and let it dry naturally.

Wall lamp maintenance method

1. The wall installed on the wall is to pay attention to whether there is a water seepage to avoid the Wall lights from falling off.Do not frequently switch when used to avoid affecting the service life of the Wall lamp.

2. Frequent switching wall lamps will greatly reduce its service life, so try to reduce the switch of the lamp when using wall lamps.

1. The advantages of the LED Solar Lamp Tube

ledThe fluorescent lamp Tube is the same as the traditional fluorescent lamp Tube in appearance, and the length is available.60cmand120cmAs well as150cmThree types, their power is respectively8WAs well as9WAs well as10WAs well as12WAs well as15WAs well as16Wand20W,and60cmThe actual power consumption of traditional fluorescent lamps is26W,,120cmThe actual power consumption of traditional fluorescent lamps is45WItemsledThe fluorescent lamp Tube only has traditional lamps40%It is an efficient and energy -saving lighting product.

advantage:

1. Environmental protection lamps to protect the earth

The traditional fluorescent lamp contains a large amount of mercury steam, and if it is crushed, it will volatilize into the atmosphere.However, the LED sunlight does not use mercury at all, and the LED products do not contain lead, which plays a role in protecting the environment.

2. Efficient conversion to reduce fever

Traditional lamps produce a large amount of thermal energy, while LED lamps are converted into light energy, which will not cause energy waste.And it will not produce the phenomenon of degradation for files.(This sentence requires professionals to adjust. LeD will also produce heat, and heat will cause LED light decay, so it is necessary to strengthen the heat dissipation function of LED lamps)

3. Quiet and comfortable, no noise

The LED lamps do not produce noise. It is the best choice for the use of precision electronic instruments.Suitable for library, office and other occasions.

4. The light is soft and protects the eyes

The traditional fluorescent lamp uses 220V AC power, so it will generate 100-120 times per second.The LED lamps directly convert the AC power to DC power, which will not produce flashing and protect the eyes.

5. No ultraviolet rays, no mosquitoes

LED lamps do not produce ultraviolet rays, so compared with traditional lamps, there are fewer mosquitoes around the lamp.The room will become cleaner and neat.

6. Voltage range: 80V -245V

The traditional fluorescent lamp is lit by the high voltage released by the rectifier, and it cannot be lit when the voltage is reduced.The LED lamps can be lit within a certain range of voltage, and the light brightness can be adjusted.

7. Save energy and live longer life

The power consumption of the LED fluorescent lamp is less than one -third of the traditional fluorescent lamp, and the life span is also 10 times that of the traditional fluorescent lamp. It can be used for a long time without replacement, reducing labor costs.It is more suitable for difficulty in replacement.

8. Strong and reliable, long -term use

The LED lamp itself uses epoxy resin instead of traditional glass, which is stronger and more reliable. Even if LED is smashed on the floor, it will not be easily damaged and can be used with confidence.

9. Simple installation

During the installation, remove the original fluorescent lamp to the LED fluorescent lamp, and remove the ballast and the ripplane.

two,LED fluorescent lamp energy saving effect

15WLEDThe brightness of the sunlight is more than the traditional40WThe sunlight is still bright,18W LEDThe fluorescent lamp is more than traditional64WThe sunlight is still bright,ledThe brightness of the sunlight is particularly softer and easier to accept.Life life5Ten thousand-8The power supply voltage of 10,000 hours isAC85V-260V (comminicateCureThere is no need to start with a gifted device, start fast, small power, no flickering, and not easy to see fatigue.It is not only super strong and energy -saving.It is one of the products developed by the National Green engineering and is the main product to replace the traditional fluorescent lamp.Low power consumption, saving60-80%Electricity is better than traditional fluorescent Tube.

three,ledfluorescent lampScope

It is suitable for most indoor lighting applications, such as family, hotels, shopping malls, office spaces, schools, parking lots, warehouses, factories, supermarkets, channels, corridors, advertising boxes and other indoor lighting.

Four, LEDLight lamp wiring diagram

1. There are two types of wiring methods for traditional fluorescent lamps: electronic zone, inductive town flow.The wiring diagram is as follows:

2. LED fluorescent lamp Tube wiring method: Remove the tingler and (or) gobinial device, and connect the fire line and the zero line to both ends of the bracket, as shown below:

installation instructions:

1. Remove the Qihui and rectifier, and connect the city's fire lines and zero lines on the left and right ends of the bracket respectively.

2. The LED lamp Tube is a built -in power supply, the G13 interface has a short -circuit state, and the interfaces of both end are consistent.

Classification of Outdoor device lighting

1. Industrial traffic venue lighting

Including the lighting of the dock, railway station, freight venue, loading and unloading stations, airfields, warehouses, public engineering and construction sites to ensure night safety and effective work.

The industrial transportation venue of the device lighting equipment can be divided into two types in terms of light distribution:

One is the site that requires a good level (surface) illuminance. The main installation of the chandeliers with better lighting functions, and the installation principles require the installation principles of the field lighting device with level (surface) illuminance.

The other is a venue that requires a high vertical (surface) illuminance. It can be installed with pan -light Lights (see light fixtures) on large spacing columns or high towers.installation principles.

2. sports venue lighting

It mainly refers to the lighting of various sports venues, such as football fields, tennis courts, shooting grounds, golf courses, etc.When choosing a lighting equipment, the visual requirements of various sports are performed for specific analysis. For example, the shooting field is high. At the same time, for the sake of safety, general lighting with soft light at the launch place and the target.

In the large sports field, the distance between the audience and the athletes requires a higher degree of illumination.Although there are not many audiences in the tennis venue, because the speed of tennis in the game is fast and the requirements are high.In addition, the selected lighting equipment cannot generate dispersion and flash effects.The stadiums surrounding the stands are generally used to install lighting equipment on high towers.This method can avoid glare, but the cost is higher.Smaller stadiums generally use lower -cost side Lights, which can be installed along the sides of the site with 8 to 20 meters of lighthouse.The lighting sources of the stadium should be metal halide lamps.

3. Outdoor lighting of other buildings

Including gas stations, sales venues, billboards, office building lighting, and the appearance lighting of plant buildings (see the night scenery of the building).

The Outdoor street lighting system is clearly illuminated by the Outdoor street lights of ordinary cities, campuses, residential communities, and large factory and mines.

Outdoor lighting lamps

LED street light

Road lighting is an important part of urban lighting. Traditional street lights often use high -pressure sodium lamps to light up 360 degrees. The disadvantages of large light losses have caused huge waste of energy.

Solar street lights

Solar street lights use crystal silicon Solar batteries to power. The maintenance valve controlled sealing battery (collagen battery) storage electricity is stored. The ultra -high -bright LED lamps are used as a light source and controlled by intelligent filling controller. It is used to replace traditional public power lightingStreet Lights.

Garden lamp

It usually refers to the Outdoor road lighting lamps below 6 meters. The main components are composed of: light sources, lamps, lamps, flanges, and basic embedded parts.The characteristics of the environment are also called landscape garden Lights.

Outdoor lighting is mainly used in urban slow lanes, narrow lanes, residential communities, tourist attractions, parks, squares and other public places. It can prolong people's outdoor activities and improve the safety of property.

Buried lamp

The lamp body is ingredients such as pressure or stainless steel, which is sturdy and durable, anti -seepage, and excellent heat dissipation performance; the surface cover is 304 # refined cast stainless steel materials, anti -corrosion and anti -aging;; High -strength tempered glass, strong light transmission, wide light radiation surface, and strong load -bearing capacity.

All solid screws are stainless steel; the protection level is IP67; optional plastic embedded parts can be used for easy installation and maintenance.It is widely used in shopping malls, parking lots, green belts, Park tourist attractions, residential districts, urban sculptures, pedestrian streets, building steps, etc., mainly buried on the ground, used to decorate or indicate lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting, and also for it for lighting.Washing walls or trees, its applications have considerable flexibility.

Washstand

It is also called a line -type LED light lamp, because its shape is long, and some people call it LED line Lights. Its technical parameters are similar to the LED light lamp.The cooling device of the strip structure of the Wall lamp is better handled.

As the name implies, let the Lights have been washed the wall like water, which is mainly used to make building decoration and lighting, as well as the outline of large buildings.Because LED has the characteristics of energy saving, high light effect, rich color, long life, etc., it is widely used.

Tunnel lamp

The tunnel light is a "black hole effect" or "white hole effect" produced by the vision to solve the "black hole effect" or "white hole effect" of the vision when the vehicle enters or out of the tunnel.The shell is used with high -intensity, good tough alloy environmental protection materials, and transparent parts are to strengthen tempered glass, dustproof and waterproof, and anti -rust resistance.

With strong anti -strength collision and impact capabilities; multi -Earthquake -proof structure and high -tech surface spraying treatment, various close -range high -strength and high -frequency vibrations cannot affect the lamps, and can be high -frequency vibration and humidity in workshops, road bases, and road rails., Long -term stable work in high temperature environments.Good electromagnetic compatibility will not interfere with the transmission network.

Landscape lamp

Landscape lights are also called decorative lighting, which are both ornamental and lighting.Landscape lights use different shapes, different light and brightness to create landscapes.For example, the red light lantern -shaped Landscape light brings a festive atmosphere to the Square, and the green coconut lanterns set up a tropical style at the edge of the pond.Landscape lights are suitable for landscape places such as squares, residential areas, and public green spaces.

In the use, be careful not to be too mixed, so as not to seize the masters, and make the landscape look messy.Landscape lights also have certain disadvantages, such as: not environmental protection, etc.

Lawn lamp

The design of lawn Lights mainly adds safety and beauty to urban green space landscapes, and generally has the characteristics of convenient installation and decorativeness. It can be used for the decoration of the green Belt of parks, garden villas, Square greening, and other places.illumination.

Underwater light

The simplicity of the underwater light is the lamp installed under the water.The appearance is small and exquisite, beautiful and generous, the appearance is similar to some buried Lights, but there is an additional installation chassis. The chassis is fixed with screws. The bottom Lights are generally LED light sources.When it is powered on, it can emit a variety of colors, colorful and colorful, and is generally installed in a Park or Fountain pool.Has strong ornamental.Mainly used in Fountains and underwater operations.

Fountain lamp

It depends on what form of Fountains, such as: dry Fountain, pool Fountain, indoor or Square (Outdoor), etc., and different installation methods in the form of Fountains are different.Generally, the wiring Tube is under the waterproof, and the position of the bottom light is left. It is enough to use the high -grade rubber and plastic cable wiring. Safety considerations should be repetitive. Remember to use a short -circuit protector.

Fence light

The LED guardrail Tube is a change in seven colors by the mixed color of the red, green and blue three -base colors. The pulse width of the output waveform is used, that is, adjusting the duty ratio of the LED light guidance.Visual inertia achieves the effect of gradient.

A lamp Tube can change seven different colors through the internal control chip, and produce various effects such as gradient, flashing, scanning, chasing, and flowing water.One meter.Anti -ultraviolet irradiation has waterproof effect.It is widely used in various buildings curtain walls, building wheel frames, amusement landscape lighting, KTV, and various bridges lighting.

Stage light

The composition of LED stage Lights is similar to LED lighting lamps. The main accessories are: shells, LED lamp beads, secondary optical lenses, LED drive power, DIP dial switch, cooling device, shell, installation stand, etc.

Moving light

Movement Lights are often used in workplaces for indoor and external mobility, as well as Outdoor television, movies, photography and other places.

Traffic light

Traffic Lights are divided into: motor vehicle signal Lights, non -motorized vehicle signal Lights, pedestrian horizontal trail signal Lights, direction indicator indicators (arrow signal Lights), lane signal Lights, flash warning signal Lights, roads and railway graphic intersection signal Lights.

car light

The types of car lights can be divided into two types: lighting and auxiliary. Among them, only the type of car lights are the fog Lights of the headlights and some car equipment, and the rest are the auxiliary Lights.

Light belt/light strip

The lamp Belt refers to welding the LED light with a special processing process on the copper line or a flexible line board, and then connects to the power supply to glow, named after its light shape like a Light belt.

[Principles of Affective Lights] What are the characteristics of the working principle of non -polar lamp?

What is the working principle of non -polar lamp

The inflexible lamp consists of three parts: high -frequency generator, coupling device, and Light bulb. The working principle is: coupling the energy of high -frequency electromagnetic field into the Light bulb by induction, so that the gas in the bulb is penetrated and forms a plasma.When the atom returns the base state, it radiates 254nm ultraviolet rays. The fluorescent powder in the Light bulb is excited by ultraviolet rays and emits visible light.

What are the characteristics of non -polar lamp

1. There are no filaments and electrodes in the bulb, and the product life is more than 60,000 hours.

2. High emitting efficiency, high -frequency non -polar lamp 80lm/w, low -frequency non -polar lamp 85LM/W.

3. The color rendering index is more than 80 or more, and the high -quality triple -based fluorescent powder is used.

4. Wide voltage work, the voltage can work normally at 185V-255V.

5. The frequency of high -frequency working frequency is 2.65MHz, the frequency of low frequency work is 230Hz, and there is no frequency flash effect on security

6. Light failure is small, and the light -pass maintenance rate can reach 80% after 20,000 hours

7, instant startup and then starting time is less than 0.5 seconds.

8. The starting temperature is low, the adaptation temperature range is large, minus 25 degrees, which can be started and work normally.

9. The power factor can be as high as 0.95.

10. Safety and reliability, green environmental protection, truly realized exemption and replacement.

High -frequency explosion -proof non -polar lamp composition

High -frequency generator

The high -frequency generator mainly includes an equivalent circuit of oscillator, filter, rectifier, switching device, matching network, driving coil and arc.It provides a high -frequency energy to stimulate and maintain gas discharge in the bulb.The high -frequency generator must have a very stable oscillating source and filter circuit. At the same time, it also has a high power factor and a low harmonic content.

All electronic components are installed in an aluminum power box, which has dual functions: shielding radio frequency interference and heat transmission to ensure the long life of the electronic device.The output frequency of high -frequency generator is 2.65MHz.

Each high -frequency generator must be combined with the same type lamp and coupler.If this basic criterion is violated, the components of the lamp will be destroyed or the electromagnetic interference will be generated.

Coupler

The coupling device is a device that combines energy from the high -frequency generator through the coil to the bulb.It consists of magnetic core, high temperature line, heat conduction rod, winding rack, base, transition parts and coaxial cables.

The role of magnetic core and high temperature line is to produce high -frequency magnetic fields.Through the heating rod in the middle, the excess thermal energy and discharge generated by the coil are transmitted to the outside through the aluminum base.There are two functions of the base: one is to ensure the connection between the bulb and the coupler; the other is to pass the excess heat to the heat sink. This heat sink must be part of the lamp.Connect with the Lights with the screws.

Connect the coupler to the high -frequency generator through the coaxial cable.The coaxial cable is connected to the coupler, and the high -frequency generator can be disassembled through the screw, the purpose is to facilitate the connection with the lamp.

The copper heating rod is extended to the center of the bulb to dissipate the iron oxygen magnetic core. There are two layers of high -temperature lines on the winding frame: one layer of conveying current, and the other layer is wrapped in the primary coil, but only one end is connected to the coil.In this way, the electric field of the second coil offsets the electric field generated by the first coil. In this way, the interference of the public mode terminal voltage is reduced to a lower value.

Light bulb

The bulb is mainly a glass bulb, which is mainly composed of bubbles, inner Tube, mercury, auxiliary mercury, etc. with a protective film and triple -color fluorescent powder, and the lamp head. It is filled with low -pressure mercury and inert buffer gases inside.

There is a glass inner Tube in the middle of the bulb, and the inner Tube is the coupling device.Through the plastic lamp head, the bulb is connected to the coupler.The installation of these two parts is generally only once, because it is a long life lamp. After installing it on the lamp, there is no need to disassemble.But sometimes (for example: at work or afterwards, when you need to change another color light), the light bulbs also need to be removed from the coupling device, but must be cautious.

There are two kinds of mercury in the Wuji fluorescent lamp. The main mercury is located in the short Tube at the bottom of the shell. Once the light is stable, it provides mercury atoms.The auxiliary mercury is placed on a close to the concave cavity, and the net is contacted with the heat discharge heat.Once the power mercury is quickly evaporated from the auxiliary mercury,In 10s, the lamp can reach 80%Light output.When the Lights were turned off, the net was cooled quickly, collecting most of the mercury atoms in the bulb to prepare to start the next start.The main mercury is guaranteed to maintain a stable light output within a wider temperature range.Auxiliary mercury ensures that the output is fast and stable.A protective film was coated in the middle of the fluorescent powder and the bubble shell to light upAfter 60,000 hours, the output of fluorescent powder maintained at about 70% of the beginning.

The use and installation requirements of light bulbs

1) light bulbs are not allowed to be used for a long time under the condition of radiator. Long -term use will cause shortened life, and it cannot work properly in severe cases;On the aluminum plate or other metal materials, 4 screws must be used. The screw must be made of electroplating or other corrosive materials; its role is to emit the calories accumulated in the Light bulb to ensure that the temperature of the Light bulb base is less than 90 degrees Celsius, soThe bulb is in a better temperature range;

3) The leader of the bulb is not allowed to be shortened or extended. It will destroy the resistance matching of high -frequency power and light bulbs, causing efficiency to decrease or damage;

4) The high -frequency power generator and the Light bulb must not be installed on the same metal heat sink, and it should be installed separately.If the conditions are not required to be installed in a metal body (such as street lights, pan -light Lights, etc.), under this condition, the distance between the high -frequency generator and the Light bulb should be pulled away.Status; if the lamp is closed, it is recommended to remove the upper cover of the high -frequency generator to benefit better heat dissipation;

5) When the coupler coaxial cable is connected to the output end of the high -frequency generator, be careful not to reconcile, and it shall not be extended, cut or damaged at will;

6) When the light bulbs are lit or just out, do not use your hand to touch the bulb directly, so as not to bring you discomfort.

In order to meet the requirements of the useless fluorescent lamp, please refer to the following terms to design, use and install the Wuji fluorescent lamp lamps.

lighting installation requirements

1) The fixed device of the bulb and the lamp must be firmly connected and tightly contact to ensure good heat dissipation;

2) Lights and high -frequency generators should be grounded according to the requirements when installation;

3) No matter what kind of lamps are used, the lamp shell must be ground.

1. How to choose lamps on road lighting

Road lightingThe quality depends on:

1. The brightness of road lighting.That is, there is enough strength to ensure that the vehicle drivers and pedestrians can see the situation around the roads on the road, pedestrians, vehicles and roads.

2. The uniformity of road lighting.That is, the distribution should be roughly uniform.

3. The degree of glare interference.That is, effectively controlling the harmful effects of glare on vehicle drivers and pedestrians.

4. The guidance of lighting.That is, proper settings are made according to the conditions of the pavement, so that vehicle drivers and pedestrians can effectively obtain information such as the direction and tilt of the road ahead, which is especially important for many roads and cross -port roads.Reasonable application of lamps can prevent glare.

Common lamps:

Littors for road lighting include high -pressure sodium lamps, low -pressure sodium lamps, polar Lights, gold halogen, fluorescent lamps, new type of Suming street lights, etc.Candidates, high -pressure mercury lamps, and low -pressure sodium lamps have gradually been eliminated due to the performance defects of light sources.Littors should use light energy reasonably to prevent glare.The light emitted by the lighting should be irradiated along the required angle, falling into the specified graphic on the road, the light is evenly distributed, the road surface is large, and the glare is small.In order to reduce glare, light control can be controlled above the maximum light.

2. Road lighting device selection

Lightsourceselectselect

The selection of light sources should comply with the following regulations:

1. Expressway, main roads, secondary roads, and branches should be used for high -pressure sodium Lights;

2. Motor vehicles and pedestrians in the residential area should adopt high -pressure sodium lamps or small -power metal halide lamps;

3. Merchant -vehicle traffic roads with high color recognition requirements for color recognition can be used in the city center and business centers. Metal halide lamps can be used;

4. The sidewalks on both sides of the pedestrian street, the pedestrian roads, and the traffic roads on the commercial area may adopt a small -power metal halide lamp, a fine pipe diameter fluorescent lamp, or a compact fluorescent light.

Road lighting should not use town flow high -pressure mercury lamps and incandescent lamps.

Outdoor lighting lamps and its auxiliary device selection

Motor lane lighting should adopt functional lamps that meet the following regulations:

1. Expressway and main roads must be intercepted or half -light lamps;

2. Half -light lamps should be adopted by the secondary road;

3. The branch road should be half -light lamps.

The non -motorized lanes that are necessary to set up lamps separately should be combined with functionality and decorative lamps that are necessary to set up Lights alone.When the decorative lamps are adopted, the on -light light ratio should not be greater than 25%, and the mechanical strength shall meet the provisions of the current national standard "General Safety Requirements and Experiments of the Lantern Festival" GB7000.1.

When using high rod lighting, according to the characteristics of the site, you should select a pan -light or interception lamp with appropriate power and light distribution.

When a closed road lighting is used, the protection level of the light source cavity should not be lower than IP54.The roads and venues of severe environmental pollution and difficulty in maintaining difficulties should not be lower than IP65.The protection level of the lamp appliance cavity should not be lower than IP43.

Activities or places with high corrosive gases such as acid -base in the air should adopt lamps with good corrosion resistance.

Large bridges such as traffic motor vehicles that are susceptible to vibrations are prone to vibration. The lamps adopted should meet the current national standard "lighting General Safety Requirements and Experiment" GB7000.1.

High -strength gas discharge Lights should be equipped with energy -saving inductors, and light sources with smaller power can be equipped with electronic ballasts.

The installation distance between the high -strength gas discharge lamp, the installation distance between the ballast and the light source should meet the product requirements.