Specification of Solar Lamp installation
Foundation
Determine the position of the light;1
rice
2
They are all soft soil, so the depth of excavation should be deepened; at the same time, there must be no other facilities (such as cables, pipelines, etc.) below the excavation location, and there are no long -term covers on the top of the street light, otherwise the position should be replaced appropriately.Reserved (excavation) at the location of the lamps meet the standard
1
rice
3
Pit;The embedded parts are placed in the middle of Fangkeng,
PVC
One end of the thread Tube is placed in the middle of the embedded parts and the other is at the battery storage office (as shown in the figure above).Pay attention to keeping the embedded parts, the foundation, and the inner ground on the same level (or the top of the screw and the inner ground on the same level, depend on the needs of the venue), one side is parallel to the road; so as to ensure that the lamp rod is erected upright and the back end is correct and the back end is correct and the back end is correct and the back end is correct and the back end is correct and the back end is correct.Not biased.Then
C20
The concrete is fixed. During the pouring process, the vibration stick shakes continuously to ensure the overall density and firmness.After the construction is completed, the mud residue is left on the positioning board in time, and impurities on the bolts on the bolt are cleaned by waste oil.During the soil solidification process, watering and maintenance should be regularly; wait for the concrete to completely solidify (generally
72
Only more than hours) can be installed in the chandeliers.
installation of Solar battery components
The output of the Solar panels must take measures to avoid short connections before connecting to the controller; the Solar cell component must be firm and reliable when connecting with the bracket; the output line of the component should be avoidedTo facing the south, the guidelines are pointed at the direction of the guideline.
battery installation
When the battery is placed in the control box, it must be put lightly to prevent the control box from being smashed; the connection line between the battery must be pressed on the wiring column of the battery and uses copper pad to enhance the conductivity;After any circumstances, short connection is prohibited to avoid damaging the battery; the output line of the battery must passPVC
After the threading Tube; after the above is completed, check the wiring of the controller side to prevent short circuit.Close the door of the control box after normal.
Lamp installation
The components of each part are fixed: the Solar board is fixed on the Solar bracket, the light head is fixed to the pick -up arm, and the bracket and the arm picking the arm are fixed to the main pole, and the connection line is led to the control box (battery box).Before the light rod is lifted, check whether the fasteners of each part are firm, whether the light head is installed correct, and whether the light source work is normal.Then work normally on the simple debugging system; loosen the Solar board connection cable on the controller, and the light source work; connect to the Solar board connection line and the Lights are off; at the same time, carefully observe the changes in each indicator light on the controller;Start up installation.When the main lamp rod is lifted, pay attention to safety prevention; the screw is absolutely tight. If the component is deviated, it is necessary to adjust the direction of the rising sun to the south.Put the battery into the battery box and connect the connection to the controller according to technical requirements; first connect to the battery, then connect the load, and then connect to the Solar board; when the wiring operation, you must pay attention toWrong, positive and negative polarity cannot collide and cannot be opposed; otherwise the controller will be damaged.Whether the debugging system work is normal; loosen the Solar board connection on the controller, and the Lights are on; at the same time, connect to the Solar board connection cable, and the Lights are off; then carefully observe the changes in each indicator on the controller;box.
Which Solar lamps are good?
1. First of all, consider the life of the whole light, there are several main factors:
1
As well as
led
The life of the Hengliu driver device
Solar street lamp manufacturers often say to the guests that I bought the best chips and the best battery, so life is the best. In fact, because the Solar street lights use DC power supply, the voltage is low and the current is large. Each component is critical.Internal resistance of a connector, the resistivity of the wire, (because becauseP
Thread damage
= 12R
To.Of course, the main reason for the actual use has proven to affect the life of Solar street lights is to determine the life and life of the battery
led
Drive circuit of light source.take
led
For the lamp beads,
led
The life expectancy recognized by the lamp beads is
5
Ten thousand
-10
10,000 hours, but conventional technology
led
There is an electronic component electronic component electronic component electronic component electronic component, the service life of the electronic component is generally
3-5
In the year, the best Japanese rubies made in electrolytic capacitors can only be used
5
The year, it was decided
led
Drived life, and our companys
led
The driver is our invention patent
led
Digital constant stream driving technology, it does not need electrolytic capacitors, so it is not limited by its life span.
led
Light beads, lamp beads
led
The life of the driver, the controller and the Solar panel is basically the same, and the main materials are semiconductor.
2
Another factor is the issue of battery life
Solar street lights are generally usedAGL
or
gel
battery, conventional technology can achieve service life in
3-5
The year is already good, our technology can do it
8-10
In the year, this was because the life of the battery was mainly affected by the frequency of deep circulation and the working environment temperature. Our Solar Lamp in other ordinary solar energy
led
Energy saving on the street light
70-85%
The patented technology greatly extends the cycle of the battery's deep cycle, thereby extending the life; in addition, the working environment temperature of the battery has a great impact on life. Our company quotes nano -technology in the battery, which can be breathable and waterproof.Below the layer, so that our battery can get the best working temperature
20-25
Celsius, and the Solar street lights of conventional technologies hang the battery on the light pole or the ground (because there is no waterproof design). It is conceivable that in the hot summer, the temperature of the battery box is so high, and the temperature rises every heavier.
10
With degrees Celsius, the battery life is reduced by half.
2. Secondly consider the brightness of the whole light
Solar street lights are not that the greater the power of the light source. Many manufacturers have falsely reported power, or buy low -luming lamp beads in order to reduce costs. In fact, the same brightness.Other companyled
The light emitting efficiency of the light source is all
80-100LM/W
, And high light decay,
1
The decline of the year
15%-30%
, And our company
led
The light source selects high -quality
led
Chip, the low light decay structure and process of patented technology, the lighting efficiency is up to the lighting efficiency
130-140LM/W
, Light failure
1
10,000 hours less than
4%
After testing, the actual light failure is only
2-3%
Right and right, and my company
led
The beads directly emit rectangular light spots, which evenly distribute all light on the road, greatly improving the efficiency and average illuminance of light source, and other companiess
led
The light spots emitted by the light source are round or use the lens imaging (the losses are also near
10-20%
), Causing a waste of light.
Third, then consider resisting the bright days of the long rainy days
At present, most Solar street lights can only be continuous rainy days.3-7
Heaven, and this is far from meeting the requirements of climate change from all over the world, because the number of continuous rainy days in most areas exceeds more than
3-7
Oh my god, and our Solar street lights can achieve the same configuration of conventional technology
3-5
Pack, Gundam
35
The day continues to light up.Why is this?The patented Solar street light controller invented by our company can make our company's solar energy
led
The street lights are energy -saving
70-85%
In other words, our company's Solar street lights
1
Power consumption at night is only configured with conventional solar energy in the same configuration
led
Street
20%
(
1-80%= 20%
),Right now
1/5
In other words, you can do it through conventional technology
6
In the rainy weather, we can be close
30
Sky's continuous rainy days.Maybe many people ask me how I did it?The principle is as follows:
A
: Solar street lights
led
The light source uses digital driver technology than conventional technology.
20%
Most of the light sources used in Solar street lights are usedled
,and
led
lighting is a need for one
led
Drive the horizontal flow source, the conventional constant current source needs to consume the entire lamp power
20%
Bost left and right, and our company uses
led
Digital constant stream driving patented technology, the power of this digital constant stream source is only
0.0625
(
IC
.
W
It can almost be ignored, so that our street lights consume power consumption.
20%
Essence
B
The
led
Driven by digital constant streaming, intermittent power supply and power saving
50%
Fans of conventional technologyled
When the street lamp is working, the power bead must be continuously powered to the lamp beads, and our companys
led
Digital constant stream, use intermittent switch to power supply to
led
light source.
led
That is, the light diode is a semiconductor device. The characteristics of the semiconductor is the switching characteristics. It is different from ordinary light sources. The number of switches is too large, which is easy to burn and damage.Switch frequency
10K-100KHz
With half of the time in the unit time, use half of the electricity without electricity, so that the Solar street lights of our company will save energy and energy saving energy.
50%
After testing, actual energy saving
47.3%
above.And the lamps are lower than the conventional constant current technology
30-40%
EssenceAt a very short switching time, the human eye and analog illumination meter are inductive.
C
The
led
Energy -saving mode of gradient energy saving mode in the middle of the night of light source
15%
above
In the middle of the night, the pedestrian vehicles on the road will be greatly reduced, so a energy -saving mode can be set up in the middle of the night.led
The power of the light source slowly reduces the power you want, and then maintains it to dawn, and other companies suddenly drop to a target value, which is not good for pedestrian vehicles. Generally, our design is the energy saving in the middle of the night.
15%
There are enough brightness.
Special Mic 
