How to choose an electric car raincoat

1. The style of electric vehicle raincoat

With the development of modern life, the style of electric vehicle Raincoats is also diverse, including layered Raincoats and pants, automatic drainage helmet electric vehicle Raincoats, and double Raincoats, canopy, and so on.The style of electric vehicle raincoat is convenient and brisk in cycling. It can be comprehensively judged according to its actual needs and prices.

2. The fabric of the electric car raincoat

In terms of the fabric selection of electric vehicle Raincoats, we pay attention to the breathability and waterproofness of the waterproof fabric.At present, the raincoat on the market is a rainpost clothes made of waterproof fabric.waterproof fabrics include tape, oil cloth and plastic film.Commonly used such as special nylon and GORE-Tex.The breathable raincoat is conducive to people scattered from the raincoat when wearing rain -resistant water and heat, increasing comfort.

3. The color of the raincoat of the electric vehicle

The color choice of electric vehicle Raincoats is also particular.The rainy weather is low, so it is best to choose a yellow electric car raincoat.From a physical perspective, the penetration of yellow light is the most.Therefore, many traffic safety reminder facilities are yellow. Choosing yellow bicycle Raincoats can not only make others easier to see you on rainy days, but also ensure the safety of you and others.

Pay attention to electric vehicle rain.

1. The amplitude covered in front of the front.The length can be more effective to block the rain.

2. The pump of the rear mirror should resist pull.Here is where the raincoat is the easiest to be damaged, especially the sea gum raincoat.

3. Whether splashing water cloth raincoat is easy to remove waterproof glue.Judgment method: Tightening the folding pressure. If the inner layer of waterproof glue has obvious creases, it is inferior material, which is easy to remove and pica.

4. Pour waterproof tape to the sewing of the raincoat.The raincoat without waterproof tape must be permeable.

5. It is best to choose a conjoined raincoat to avoid throwing rainwater from the waist. At the same time, it is best to tighten the cuff pants.

6. The fabric must be thicker to prevent the wind from being torn in the wind during high -speed cycling.

Disclaimer: The above content is derived from the provision of the program system index or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt; error correction & gt; & gt;

How to install an electric car sunshade

1. Prepare a wrench in advance to confirm that the electric vehicle sunshade shed is complete and non -damaged, and the accessories are not omitted.

2. Understand the hexagonal screws of the rearview mirror with a wrench, remove the two rearview mirrors, place the connecting rod of the sunshade between the rearview mirror and the electric car body, and twist the rearview mirror.

3. Insert the two sleeves in the front of the sunshade into the connector, be sure to insert it to the end, so it is very tight.

4. Pull the back of the sunshade to the rear box of the electric vehicle, and tie them on the electric car body on both sides with ropes. If you want the position of the ripkin, you can also tie it to the back of the rear box.

5. At this time, there are four elastic rods in the remaining accessories. The two thicker and rigid ones are reinforced on the top of the shed, which are connected respectively.

6. The other two long and soft elastic rods are supported by the side of the rails, which are connected separately to complete the installation.

What should I pay attention to when installing an electric vehicle sunshade

1. Be sure to reserve the expansion space, the screw spacing, which can be made according to the thickness of the board. It is too small and too large.If the spacing is too small, sometimes it will cause stress due to too tightly, causing damage; if the spacing is too large, the PC board may not be unstable.

2. The plasticizer in the PVC cushion and the chemicals in certain rubber pads will be migrated to the surface of the cushion. After contacting the PC board, the PC board will be destroyed, so it is absolutely not available.It is recommended to use the material of the cushion, the product of the Sanyangi Copycopar, silicone rubber and chlorine rubber.If there is no suitable padding, it is better not to use it, nor can it be used to destroy the pad of PC.

3. In addition to the waterproofing, the double -sided waterproof tape can also be used for the pad material between the PC board and the frame.Some double -sided tapes are damaged in the face of PC boards, so they are also selected during installation.

4. PC boards are very easy to scratch. Do not tear the protective film when installing.Before cutting, the marker must be marked and marked as much as possible on the protective film. If it must be marked directly on the plate, please use a crayon to avoid using sharp tools to contact.