1. How much is the probation light?

Detective lamps, also known as Outdoor probe lamps, are commonly used outdoor lamps. They are widely used in Outdoor landscape lighting and Outdoor safety prevention areas. Many donkeys will buy a probe lamp to help Outdoor photos. So what is the price of the probe lamp?

Generally speaking, the price of the probe Lights is mainly affected by factors such as lamp sources, power, accessories, brands, performance, irradiation distance, etc. Because of the quality gap, the price is also high and low, the ordinary ones are about 50-100 yuan, and it is more expensive.It takes 300-500 yuan. These are home-based scratch. If it is a large probe lamp on the truck, the price is much more expensive, usually thousands of yuan.

2. How to buy Outdoor visit Lights

When traveling in the wild, donkeys will use Outdoor probe Lights. When buying Outdoor visit Lights, the main factors that need to be considered are the following points:

1. Brightness

The higher the brightness is generally better, but the brightness is too high, which will also affect the life of the light source, and the heat is large and the battery life is poor. Therefore, the brightness of the ordinary Outdoor visits is generally not particularly large.Objects have better lighting function.

2. color temperature

The color temperature of about 4300K slightly yellow is more suitable for human eyes. The color temperature (that is, Blu -ray) of more than 5600 people will lose the layer and cannot see the details.

3. Light source

The size of the light source of the probe light is related to the hardness of the light. The larger the light source, the softer the light, the more likely to perceive the three -dimensional objects and detect the obstacles, but the corresponding irradiation distance is also shortened.When buying, you can choose according to your use. The long -range lighting source sources are smaller, and the sources of pedestrian Lights and camp Lights are larger.

4. Light distribution

Seeing whether the light and darkness is different in the lighting area, whether there are concentrated spots. Outdoor lighting generally requires a bright light spot in the center of the light area to illuminate the target, and there is a certain range of scattered scattered around to see the road or environment.

5. Protectiveness

Outdoor visit lamps are used outdoors after all, so they require certain protection performance. Usually IP Levels are expressed that general use can reach IP43 protection, mainly to prevent light rain and occasionally falling into the water; if it is under high intensity and bad weather, it is recommendedSelect the IP67 Protection Detective Light.

6. Endurance

The endurance capacity of Outdoor probe lamps is high or low. It is recommended to choose a viewing light for the high beam to reach more than six hours (including the backup power supply), which requires the replacement of the power supply.

one,Landscape Bright ProjectWhat problems exist

1. The overall planning is lagging, no planning or no planning engineering facilities construction, and the phenomenon of disorderly and uncontrolled cities makes the city light up.

2. Copy copy and imitate blindly.In the process of night scene lighting, in the process of night scene lighting, regardless of the characteristics of the city's own, historical and cultural characteristics, and their own financial conditions, blindly study the characteristics of light construction in other cities. Simple imitation will inevitably lead to the same as each other.

3. Only grasp the festival and ignore the usual night scene lighting.The night scene lighting of festivals or major political activities is understandable, but the city's night scene lighting is by no means just a few festivals.

4. Ignoring the scenery and safety of the day, some lighting projects are beautiful at night, but at a glance, it is not beautiful and uncoordinated with the surrounding environment during the day, and there are hidden dangers.

2. How to reasonably design the landscape lighting project

1. Do not design a Chinese and unpretentious landscape lighting project, which requires coordination with the local geographical environment and overall style.Paying attention to practicality, while beautiful, can also play a role in guiding landmarks.

2. The planning area of the planned city should not be too large, do not have too much in number, and do not build a large amount of rockery falling projects such as waterfalls and waterfalls, artificial water systems, and other landscape lighting projects. This will waste a large amount of resources and energy. It may exceed the local economic and social development level andFinancial tolerance.

3. Dailyization of landscape lighting projects.Do not open the landscape landscape to light up on the holidays, and return to the bland after the holiday. You must achieve daily unity.

4. A complete lighting project should be a change in spring, summer, autumn and winter, rather than only a few important festivals.

5. Don't blindly light up the streets on the street because you like the beauty of the light, leading to the high light color, destroying the original visual effects of the landscape, and losing the hazy beauty at night.

6. The landscape lighting project needs to achieve the overall lighting design.

3. precautions for Landscape lighting Project

1. Energy -saving

lighting should start from functional needs, decorative Lights should conform to the function of "beauty", reflecting a cultural accomplishment and cultural atmosphere.

2. Avoid disorderly development

Avoid disorderly development and excessive development of landscape lighting.The urban lighting project requires the participation of professionals, and the overall planning and design.The brightening project of the prosperous neighborhood requires scientific planning and strictly implement relevant standards.

3. Combination of urban planning

The combination of night scene lighting and urban planning, formulating the overall planning development of urban lighting according to the characteristics of the city, has made the entire city's night lighting focus outstanding and distinctive.On the one hand, it is necessary to strengthen the light environment management and divide the light environment function; on the other hand, it is necessary to run strictly in accordance with the standard design standards, which is the "low -carbon" road for urban lighting.

1. What is the scope of the lawn Lights?

Lawsticks are a kind of outdoor lamps, which are mainly used for decorative lighting of green belts in parks, garden villas, Square greening, and other places. It provides the effect of lighting embellishment lighting at night at night. How much can the lawn Lights be exposed?

It is understood that the lighting area of a lawn light can cover the height of the lawn Lights and the brightness of the inner light source and the design effect of the lawn Lights, such as a cylindrical lawn light with four -sided light.In the light source, the irradiation area is about 5-15 Square meters.If the light source is large and height, the irradiation range is wider.

Because the light source installation method of the lawn Lights is not the same as the lighting method, there is no fixed irradiation range value. The specific ones can contact the manufacturer to provide the corresponding style or custom design and production according to actual needs.

2. How much is the spacing spacing of lawn Lights?

When installing the lawn Lights, the problem of installation is needed. If it is too dense, it will look stiff. It is too thin and cannot give full play to the effects of lighting and decoration. So how much is the gap between the lawn light?

Generally speaking, most of the lawn lamps are more common at corners, trails or corners of light. The installation spacing is mainly different according to the light source and height:

1. Under normal circumstances, lawn Lights are needed for environmental decoration and travel. The installation spacing is about 6 to 8 meters; if 36W or 70W gold halogen Lights and sodium Lights are used, it can be relaxed to 10m spacing.

2, a 0.5 -meter -high lawn light, uses a energy -saving light of about 23W as the light source, can be farther away, about 11 meters.

3. The 3.5-meter-high lawn Lights are generally regarded as courtyard Lights. The light source is 15-30W, and the spacing can be set between 8-12 meters.

The above is a spacing design under normal circumstances. It can be appropriately encrypted near the steps, grass, corners, and flower platforms. While beautifying the environment, it also guarantees the safety of people walking at night.In addition, it is important to note that if it is a Solar lawn light, in order to prevent the weather from unsatisfactory weather conditions, it is necessary to choose auxiliary electricity to achieve lighting, and pay attention to the size of the distance.

1. How high the landscape lamp is generally

The Landscape light must choose the appropriate light column height to ensure uniform lighting.The height of the landscape lamp is related to the purpose. The general Landscape light is about 3 meters. The space of a large number of people is generally about 4 to 6 meters.

Second, how much is the landscape lamp spacing appropriate

1. Light lawn Lights on all sides. Generally, the 18W energy -saving Tube light source is used. It is suitable for various garden gardens, sidewalks and trail lighting. It provides pedestrian night lighting. The lighting time is usually 18: 00 ~ 6: 00.The distance between the commonly used lamps is 6 ~ 8 meters, and there is no clear specification from the roadside, but it is generally designed between 0.2 and 1.5 meters.

2. One -way outlet light lawn Lights are used in wider roads and use 26W energy -saving pipes or 35W gold halide lighting sources.The distance between the commonly used lamps is 8 ~ 10 meters, and the generally designed between 0.5 and 2.0 meters.

3. Garden Lights generally use 70W gold halide lighting sources. It is suitable for activity gardens, wide sidewalks, and lane lane lighting in the community. The distance between the lamps is usually 10 ~ 15 meters.It can also be evenly arranged in the center of the courtyard according to the number of lamp design without being restrained by the roadside distance.

4. Other Landscape lights, generally choose from the project style, the preferences of the owner, or the non -standard design. The distance from the roadside is generally between 1.0 and 2.0 meters.

5. The street lights of high light rods are used with 150W gold halogen lighting sources. The distance between the lamp is usually 15-20 meters. Generally, it is set in the road isolation Belt. The distance from the roadside should be determined in conjunction with the width of the road isolation Belt.

6. In addition, some special lamps, such as aluminum cast lampstrangle, explosion -proof glass lamps, surface -shaped landscape style lamps, etc., often set up directly on the edge of the garden road, corner of garden roads, small trails, light dead corners, etc.What distance is left to the roadside.

1. What are the factors that affect the waterproof performance of street lights

1. Ultraviolet

Ultraviolet rays have damaged effects on the insulating layer of the wires, shell protection coatings, plastic parts, sealing glue, sealing rubber strips, and adhesives exposed to the street lights.

After the insulation layer of the wire is cracked, the water vapor will penetrate the inside of the lamp through the gap of the wire core.After the lamp shell is coated with aging, the coating of the edge of the shell will crack or strip, and there will be gaps.After the adhesive gum aging between the electronic sealing collagen, the sealing glue strip, and the structural parts, the adhesion, deformation, cracking, and the gap will also be reduced in order to reduce the waterproof performance.

2. High and low temperature

The temperature of the Outdoor daily changes greatly. The surface temperature of the summer lamps during the summer can rise to 50-60 C, and it will fall to 10-20 C in the evening. The temperature of the ice and snow in winter can be reduced to zero, and the temperature difference between the year will change greater.Under the high temperature environment of Outdoor street lights, materials will accelerate aging and deformation.When the temperature drops to zero, the plastic parts become crispy, and it may crack under the pressure of cold air.

3. Hot expansion and contraction

The shell of the outdoor lamps will cause thermal expansion and contraction due to changes in temperature. The lineflation coefficients of different materials will be different. The two materials of glass and aluminum profiles will displacement at the combination.The process of thermal expansion and contraction is continuously repeated, relative displacement is repeated, and the air density of the lamp is greatly damaged, the gas density is poor, and the waterproof performance is greatly reduced.

2. How to deal with Outdoor street lights and waterproof

At present, Outdoor street lights are mainly divided into two major directions: structural waterproof and material waterproof. Structural waterproof is to improve the structural protection performance of the lamp body and enable it to cope with the harsh Outdoor environment.The position of glue density electrical components is used to prevent waterproof with glue material during assembly.The treatment method of Outdoor street light waterproof treatment is specifically:

1. waterproof waterproof at the imported line hole

The entry and exit line of Outdoor street lights is the easiest place to enter the water. Therefore, the screws and nuts of this part must be tightened in place. The entry and exit cable cannot be easily pulled out. You can use the Gaza Belt, glue and other methods to be fixed.If the lamp is buried underground or in water, then it is allocated at the bottom. The occasions used are that the lamp body is more infiltrated by water, and the import line must be increased.

2. glass splitting waterproof

If there is a glass rubber ring, first fix the groove of the tank or rely on the edge of the lamp body or the light in the lamp to play a small amount of uniform waterproof glue to increase the squeezing and sealing of the rubber ring when the tightness is tightly locked;If there is no glass rubber ring, first in the glass gum, the waterproof glue is placed obliquely.

3. Cover the glue ring to fight screw waterproof

First consider the fixed rubber ring. Generally, the lamp body has no glue groove. The thickness of the rubber ring and the side of the screw hole is fixed first; if the lamp body has a glue groove, first play a small amount of glue in a circle in a circle.Fix the rubber ring first; for the lamp body with waterproof structural waterproof, it is also necessary to evenly beat some glue on the surface and side of the tape.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is effective. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt;Correction & gt; & gt;