1. How to adjust the Bicycle code watch
Generally, the upper right of the Bicycle code watch is the RESET (reset) key, referred to as the reset key, the top left is the set (set) key, referred to as the settings key; below the table is the Mode (mode) key, referred to as A key.Each time the MODE key is pressed, the display content of the code watch (time, distance, etc. switch), the SET key is pressed during adjustment, the reset key is pressed to clear the data, the bicycle code meter adjustment is very simple, and the electronometer is adjusted to the electronic meter.almost.
Second, Bicycle code watch setting instruction manual
Initial settings
Press the settings key first, and then hold the settings key for about 3 seconds.First press the mode key to switch to the function menu that needs to be changed, and then press the settings key to enter the secondary menu. At this time, the place that can be changed will flash, then press the reset key to adjust the specific parameters, then press the settings key to confirm the change.After setting up the screen, the "SET OK" prompt will be displayed.
The reset key is to clear the zero reset; the settings are confirmed; the mode key and the reset key are adjusted.
The content and main functions of each menu are as follows:
1. Language (Language Settings): There are 7 languages to choose from. Here we will set "English".
2. KMH/MPH (speed unit): There are 2 speed units to choose from, here we set "KMH".
3. WS BIKE1 (bicycle Wheel Size): Enter the perimeter of the wheels directly.Method: Diameter 3.14 (meters).
4. CLOCK (clock setting): Set the current time.
5. Total ODO (bicycle Mileage Mileage): Set the initial value of the total riding mileage.The mileage unit is KM.
6. Total Time
7. Contrast (display contrast): There are 3 options, which are 1 (light), 2 (standard), and 3 (thick).
After all the above settings are completed, the code -stuck can be used into the table and can be used normally.
Use settings
Press the Mode (mode) key to switch:
1. TRIP DIST (a single itinerary distance): Show this cycling distance.Long press the reset key to clear.
2. TRIP TIME (single schedule): Show this cycling time.Long press the reset key to clear.
3. AVG.Speed (average speed): Show the average speed of the cycling.Long press the reset key to clear.
4. Max.speed (maximum speed): Show the maximum speed of cycling.Long press the reset key to clear.
5. CLOCK (clock): Show the current time.
6. Total Odo (Total Mileage): Show the total riding mileage.
7. Total Time: Show the total riding time.
Expand function
Stub function (STW), instant temperature display (TEMP), minimum temperature (MNTEMP), maximum temperature (MXTEMP), instant calorie consumption (CAL), total calorie consumption (KCAL), fat combustion (FAT), target journey upward settings (KM), ride time setting (Time), opening scan mode (SCAN, riding time, average speed).
Tip: If the expansion function is turned off, it will not be displayed in the main mode. Generally, the new code table is closed by default. If which functions are needed, you can open it by yourself.
3. Steps setting up the Bicycle code watch
At the same time, press the SET key Mode key (long press for 3-5 seconds) to initialize the code table.
After initialization, first choose the Chinese language, and press the Mode key to convert to ENGL (English).
Press the SET key again, we will see the KM mode, which does not need to be adjusted under normal circumstances.
Then press the SET key, enter the setting wheel diameter mode, and press the Mode key to set the wheel diameter (the default setting is 2155mm).
Then press the SET key to enter the total mileage settings (generally no settings are required when the first time is used, when the code watch is lost, we can enter the total mileage settings).
Press the SET key to enter the maintenance settings. We can set a certain driving distance to maintain the car.
Then press the SET key to enter the shutdown mode. When the code is not used, enter the mode to turn off, saving the battery consumption.
Then press the SET key to set the weight unit kilograms and pounds.
Then press the SET key to set your personal weight (default 65kg).
Then press the SET key to enter the time system setting (generally select 24 hours).
Press the SET key and enter the time settings.
Tip: Some bicycle codes are set up for 5 seconds of full -screen backlight at any keys, and long press for 5 seconds to enter the extension function mode (Expert).
Single mileage zero settings: Press Mode right -click Tagkm or English TRIP French DIS file, and then press the SET left button for more than 3 seconds to clear zero.