1. What types of road Lights are

1Divided by the height of the street lights: high rod street lights, middle rod Lights, street lights, courtyard Lights, lawn Lights.

2Divided by street lights: hot -dip galvanized iron street lights, hot -dip galvanized steel street lights and stainless steel street lights.

3Divided by the street light source: sodium light street lights,ledStreet lamps, energy -saving street lights, new type of Summing street lights.

4Divided by styling: Chinese Lights, antique Lights, Landscape lights, single -arm street lights, arms street lights.

5Divided by power supply: city circuit lamps and Solar street lights and complementary scenery street lights.

There are many types of street lamps. Different lighting technologies are suitable for different needs. The fundamental purpose is to design a high -efficiency electronic energy -saving street light with long life, low power consumption, high power factor, and small current harmonic content.

2. What is good for street lights

The street lighting is generally used for high -pressure sodium lamps,Metal halide lamp is also a common source of street lights.From the perspective of lighting, incandescent lamps are the best, but the light flux is low and the light effect is poor.fluorescent lampThe same is the fluorescent lamp. The light emitting principle depends on the gas electrical ionization to stimulate fluorescent powder to light up. Its color rendering is low, but the light flux and the light effect are much better than the incandescent lamp. The neon Lights are almost no other benefits except for good -looking.Extremely low, you cannot do special lighting Lights; the performance of metal halide lamps is very good, especially its power can be made very much than other lamps; LED lights are highly efficient and energy -saving and environmentally friendly, but there are certain certainty.Technical defects.Therefore, in general, it is more appropriate to use metal halide lamps or LED street lights now.

What is the difference between street lights and Landscape lights

1Different height

The difference between street lights and Landscape lights is mainly reflected in the height. The conventional height of street lights is6-12Mi, there are also some routine heights of some street lights are6-20rice.But the general height of Landscape lights is3-6Mi, this is because Landscape lights are ornamental. You do nt need to do too high. The higher the materials you need, the more expensive the cost.

2Different lighting power

Because the street lights are to provide sufficient illuminance, their lighting power is generally large, generally in250-400WWithin the range, the specific power is considered according to the width of the road, the surrounding trees, the height of the light rod, and whether it affects the surrounding residents.

Landscape lights are relatively small, generally80-150WIt may also be smaller, because the landscape lamp has a basic lighting effect. Its biggest effect is to provide strong ornamental. Its light source power can reflect the overall shape of the lamp.Too bright.

3Different applications

street lights are generally used in the main roads, secondary roads, urban squares, communities and other places in cities or villages. lighting needs are generally relatively large.

Landscape lights are generally installed in independent areas, such as parks, gardens, high -end communities, commercial pedestrian streets and leisure squares. Landscape lights are also used in many tourist attractions.

4Different functions

The main role of road Lights is lighting, which must be able to provide pedestrians and vehicles with better lighting.But Landscape lights only need basic lighting. The most important thing is viewing, which is used to decorate the surrounding environment and create an atmosphere.

The shape of the street lights is not so diverse, and there are generally several types.But the Landscape lights have a lot of shapes, very casual and unrestrained.It can be customized according to the surrounding environment and special reasons.

1. What is the principle of induced street lights

The induction street lights can be induced by the use of infrared induction modules and PMW control to detect the thermal radiation of the human body, so that when someone is close to the highlights of the high light, the brightness of the light to weaken the light after leaving, and achieve the effect of saving energy. It is an intelligence. It is an intelligence.street lights.

There is a single -piece control in the induction street light. By adjusting the duty cycle to control the brightness, the lamp beads use environmentally friendly LED lamp beads.The induction distance of the inductive street lights can be selected according to the installation interval of Solar street lights. Even if the distance is far away, the induction is sensitive and the humanization requirements can be met.

2. Introduction to the work process of Solar sensing street lights

1. During the day, there is sunlight to charging. The ideal state is 8-10 hours of charging.

2. At night, the lamps are automatically launched to light up. When someone is passing by, the infrared induction device is triggered, and the light is automatically turned on. The strong light generally lasts 30 seconds.Bright mode.

3. When the person leaves the induction range, the light is automatically turned into a slightly bright mode, and the next time someone approaches the strong bright mode.

3. What are the advantages of induction street lights

1. Energy saving and environmental protection:The advantages of induction street lights are mainly energy saving and environmental protection. Because it is a automatic control product made from infrared technology. When the human body enters the inductive area, the switch will automatically connect the load.After leaving, the delay design will automatically turn off the load after leaving, and it is very good to "people go to the Lights, people leave the Lights", avoiding the waste of energy.

2. Automatic light metering:The switch of induction street lights has an automatic light metering design. When the light is strong during the day, the induction work will be disconnected; and the induction street light has no contact electronic switch, which extends the load life.

3, reliable induction:The use of thyristor lines, high safety, wide induction range, and sensitive induction performance.

4. High cost performance:The induction street lights use full -plastic lamps, which is not easy to deform, discolored, damaged, and has a long service life; and the price of induced street lights is not expensive. Because solar energy is used as a source of electrical energy, the cost of use is not too high.

1. Common faults and maintenance of Solar street lights

With the gradual adjustment of my country's energy structure, Solar resources are widely used. Solar street lights are street lights using Solar lighting. During use, there may be some faults. The following is a common failure and maintenance method for Solar street lights:

1. The whole light is not bright

Solar street lights are Outdoor lighting. They often encounter high temperature or rainy conditions, low temperature or rainy weather, etc. The controller of Solar street lights is usually insidePhenomenon.First check whether the wiring site of the controller has water traces or rust. If so, it is likely that the controller has been damaged. If there is no battery voltage measurement, such as 12V Solar street light power supply system, the battery voltage is lower than 10.8V, the battery has been storage.No electricity, you need to replace it.Check if there is voltage and current output under normal working conditions.If there is no, the batteries are damaged and replace the batteries.There is no problem in the above, you should check the light source. Only the light source is connected to the power supply. See if it Lights up, the light source is replaced without light.

2. The lamp head flickered

The cause of this failure is poor, the battery is lost in power, the battery is lost, and the amount of power storage has been severely reduced. If the line is fine, the battery is replaced.

3. Short lighting time

Generally, it is caused by rainy days without the sun. If the rainy day durates short, it is usually caused by the decline in battery storage power and insufficient power storage capacity.

4. The source of Solar street lights is not bright

Many Solar street lights use dot matrix LED light sources. Except for the quality problem of LED light sources, some lamp beads will cause this situation.The solution is to replace the corresponding lamp beads, welded firmly or replaced the entire street lamp head.

Second, the Solar street light is broken

Solar street lights are working outdoors. Even if the quality is good, it will inevitably fail. So who should I find if it is found that the Solar street light is broken?

Generally speaking, the Solar street lights are broken, depending on where the Solar street lights are installed:

1. If the Solar street lights on the municipal road are broken, you can contact the local municipal street light management department to let the street light management department go to repair.Essence

2. If the Solar street lights in the community are broken, you can contact the property department to let the property be repaired.

3. If the Solar street lights of the scenic area or Park are broken, they can generally report to the staff center or Park management office to report to the staff, and they will send people to repair it.

4. If the Solar street lights in rural areas are broken, as long as you buy Solar street lights produced by regular manufacturers, contact the manufacturer. The manufacturer will send professionals to contact the person in charge of the village.If the user cannot solve it, they will send professional and technical personnel to help solve the situation where the street lights are not turned on.

1. What street lights are Solar street lights

Solar street lights use crystal silicon Solar batteries to power. The maintenance valve controlled sealing battery (collagen battery) storage electricity is stored. The ultra -high -bright LED lamps are used as a light source and controlled by intelligent filling controller. It is used to replace traditional public power lightingStreet Lights.Solar street lights are composed of several parts such as LED light sources, Solar cell panels, batteries, battery insulation boxes, Solar street light controllers, street lights, and auxiliary materials wires.

The working principle of Solar street lights is: Under the control of intelligent controllers, Solar cell panels absorb Solar light during the day and convert into electric energy, charge the battery pack, and provide electricity to the LED light source to power the LED light source at night.Electricity can be stored to ensure the normal work of rainy weather.

2. How much is a set of rods in Solar street lights?

The price of Solar street lights is affected by factors such as the height of the light pole, the light of the light head, the power of the power, the length of the lighting time., Lantern flange sleeves, basic embedded parts and built-in wires, ranging from about 2500-1000 yuan according to the configuration.For example, a 6 -meter -high, 30 watts of Lights, and 6 hours of light per day. The price of such Solar street lights is about 2400 yuan.(The above price source network is for reference only)

3. How to choose a more cost -effective Solar street light

1. Look at the detailed configuration

The configuration of Solar street lights with relatively high cost is relatively reasonable. Solar street lights look at the basic configuration mainly depends on the power of the lamp, the capacity of the battery, the size of the battery plate, the material of the light rod, etc.Buy products with virtual capacity.

2. Look at the needs of the road

Solar street lights need to determine the height and distance according to road needs. First of all, you need to know the width of the road used in Solar street lights, so as to choose a single arm or Solar street light; secondly to see the interval between Solar street lights, the power of the choice of lamps needs to be reached.What brightness is; in the end, it depends on the height of the Solar street lights to determine the size of the lamp power and brightness.

3. Look at the quality guarantee time

Under normal circumstances, the warranty time of Solar street lights is 1-3 years. The longer the warranty time, the more guaranteed the quality of the street lights, but the price will be relatively high.

4. Look at the brand

To buy Solar street lights, you should pay attention to the strength and reputation of brand manufacturers. This can be understood by online query methods. You can go to each brand to consult to understand the specific strength of the manufacturer.

1. What is the reason for Solar street lights

1. The reason why Solar street lights can be turned on is mainly because there is a battery, and there are three types of batteries. One is a lead -acid battery. Its service life is only two years.The life of colloid batteries is relatively long, which is about three years.Many Solar street lights now use lithium batteries. The maximum service life can reach about 6 years. If the lead -acid battery is selected, it may occur after one or two years.Not lighter failure.

2. It is also possible that the controller of Solar street lights is damaged. After wind and rain, lightning strikes or other reasons, the controller cannot run normally.

3. It may also be that the light source of the lamp head is damaged. If it is not artificially damaged, it may be that the battery is damaged or other natural reasons cause the Solar street lights to not run normally, and there is a problem of not bright or flickering.

4. The last reason is that the line has aging. This phenomenon is also more common. The aging lines have disconnected, and Solar street lights cannot work normally.

2. How to repair Solar street lights

1. The best choice for the installation Solar street light battery is the lithium battery. The service life is relatively long. When installing, you need to pay attention to the voltage and capacity of the battery. At the same time, you need to debug after installation.

2. If the controller is damaged, the original controller should be removed, and then the same type of matching controller is selected, and debugging is required.

3. If the light source of the Solar Lamp head is damaged, it can only be replaced, and the welding should be firm. At the same time, pay attention to repair the line.

The above introduces the reasons and maintenance methods of not bright Solar street lights. The Solar street lights may not be on. It may be that the battery life is short, controlled damage, the lamp head damage, and the line aging. As long as the reason is found, the maintenance can be corresponding.