1. How to install Outdoor folding tables

A family Outdoor camp can carry an Outdoor portable folding table, which is very convenient to use Outdoor folding tables to play cards, drink tea, and barbecue.How to install it?

1. Preparation before assembly: Preparation tools: cross or word screwdriver, wrench, pencil, it is recommended to use a pistol electric drill.Putting the circular fixing head into the cross -side side of the connected head in the pores is exposed, and the fixed head gap is aligned with the position of the cross section.

2. Twist the connection rod into the rising plate that has been embedded in the board. It is best not to twist to the end. Put the universal wheel with the No. 14 wrench into the mobile door marked with the drawing. You do nt need to twist to the end. The height is adjusted later.

3. Turn the handle into the tapping hand holes. Pay attention to the front and back of the door panel. There is no side of the pages. The handle screw may be too long. ThereforePut the pad between the screws and the door panel.

4. When leaving the factory, you only have a pre -drilled screw hole on the mobile door and door panels. The union holes of the two side panels and the top board are not pre -drilled. This is for buyers to install it., Can only make buyers suffer a few more screws.The screws of the fixed pages are self -attack wires. Even if there is no pre -holes, it can be conveniently screwed in with a screwdriver.

5. Inside the folding table, the top panel is exposed to the ground, and the two -piece desktop and the No. 1 top plate are connected with the unity.Move the door panel, support the desktop, insert the plug -in head into the hole on the back of the desktop, take a pencil drawing position on the mobile door and fix the insertion and the insertion eye.

6. When assembling the folding table, you should lay felt cloth or carton on the ground to avoid scratches from the table.When installing the pages, because the surface of the board is relatively hard, the screw is difficult to twist. You can hold the screws first, knock the screw with the hammer a few times, and leave the plate to leave a small hole in the depression, so it is easy to twist.

The above is the installation method of Outdoor folding tables. Different outdoor folding table installation methods may be different. However, the installation instructions will be accompanied by the general purchase, which can be installed according to the instructions.

2. What are the precautions for installing Outdoor folding tables?

1. Do not get started to install the outdoor folding table. First look at the installation instructions and install it according to the manual to avoid being installed casually. Otherwise, it is troublesome to disassemble or remove it.

2. Before installation, you should carefully see if the parts and the installation tools are complete.

3. During installation, screws, connecting rods, etc. The parts that need to be twisted should be screwed in place, so as to be firm.

4. After the installation is completed, you need to test it to see how the weight is, whether it is strong, and inconvenient to folder.

1. How to match the rattan table and vine chair is more fashionable

The function of the rattan chair:

In addition to the main skeleton part of the vine furniture, most of the vine noodles are prepared by fine vines, so that the furniture has gaps, good breathability, and increases the comfort of contact.Because of the soft texture and high ductility, Tengcai can shape more changing shapes or lines, and therefore is often used to make casual chairs that focus on soft touch.

In order for young people to accept, vine furniture will do special dyeing treatment to meet the needs of more age -layer consumers.In addition, rattan furniture also changes more in shape.Combined with composite materials, it is made of bronze metal or soldering iron strips as handle or tables and chairs.Or with a cute cloth pad can make the vine chair look more modern.

The furniture made of vines mainly includes bed tables, seats, sofas, coffee tables, coffee tables, leisure chairs and cabinets.Because the rattan noodles are soft, it will not be used as load -bearing furniture, and the rattan home accessories are mainly containers such as puts, vases and other containers.At present, the materials, handicrafts and technical sources weaving of Fujima are dominated by the traditional craftsmanship in Southeast Asia. It is full of ancient Nanyang style and is loved by middle -aged groups.

The color matching of the rattan chair:

The vine materials rich in natural charm can make full use of natural materials to create excellent effects, such as placing fruits or dried flowers and dried fruits in vine baskets or vine vases.The main matching method of rattan furniture or rattan jewelry is in addition to mastering the principles of nature, elegance, and leisure, followed by color.When the main color of the space is dark, the purchased vine products can tend to brown or dark brown.Light -colored home space, you can choose a rattan or other rattan vine, with a fancy and bright cushion or cloth accessories.

2. How to buy good quality rattan tables and chairs

First, sit up and try it in person to see if there is a crunch when shaking or being too heavy.

Second, see if the welding point at the welding is firm, and the surface of the rattan system should not have a lot of exposed connection ports.Be sure to touch it with your hands, Smooth and flexible.

Third, it depends on the workmanship. See if the rattan is evenly compiled.Select products with uniform thickness and consistent color, seeWhether the fabric is sewn is delicate and whether the hardware is high -end.

Fourth, the rattan chair is both breathable and elastic. It is best to choose a back chair with a back, and put a stool on the foot to make your legs flat and prevent the lower limbs from ischemia.

Fifth, some rattan furniture is actually imitated with plastic and other materials. Observing the fractures of the vines on the furniture. If it is plastic and other products, it will be particularly neat, and the rattan fracture will be frizzy.

Sixth, the toughness of the rattan is the most important. It is recommended to find out those small parts on the back of the furniture. Twist it with your hands. The inferior vine will easily break the residue. Good vines generally will not break.

top ten brands of vine furniture & gt; & gt;

one,Conference tableHow to put mineral water

Due to the request of the meeting to provide beverage services, the standard meeting is generally provided with mineral water.

mineral water is on the right side of the Sika.When placing mineral water, the mineral water is generally placed on the right hand side of the participants to facilitate the participants to get it.If the bottle water is placed, the tag of the bottle should be faced to yourself to avoid mistakenly obtained.

The placement of mineral water at the Conference table will vary from the preferences of venues, culture and organizers.However, the following are some suggestions to refer to:

1. The desktop is neat: ensure that the desktop is clean and the flawless mineral water bottle is placed.

2. Easy to use: Place mineral water in places where the participants are convenient, such as the corner of the table.

3. Place the order: Place the tea cup next to the mineral water to facilitate the use of the participants at the same time.

4. Keep consistent: The placement of tea cups and mineral water bottles should be consistent to show professionalism and neat image.

5. Following cultural habits: Considering local cultural habits, such as the placement of tea cups in Chinese culture may be different from Western culture.

6. Consider environmental protection: minimize the use of disposable cups and bottles as much as possible, and can provide reusable cups and large bottle water.

7. Prepare sufficient mineral water: Make sure to prepare enough mineral water according to the scale of the meeting and the number of participants.

2. Conference desktop items placement standards

1. Tea cup: On the upper right side of each position, the cup handle is to the right,StoremateIn the face of the guests, the cup is 5cm from the table on the table at a meeting table, and the label pad is placed below.

2. Biter cup: Put on the upper right side of each seat, usually on the left side of the conference cup, the hedging cup and the tea cup are 1cm, and the coasters are placed below.

3. mineral water: On the right of each hear cup, the Trademark of mineral water is faced with guests (regular meetings entertaining general mineral water bottle).

4. Oxavar: Generally, there are three seats in the general meeting, a pan -cylinder in the center, and 1,5cm in front of the table at the table.

5. towel support: Put on the upper left side of each conference position with 2cm interval. The upper end of the towel support and the conference cup is a straight line.

6. Meeting paper: Put on the right side of each guest's chest. At the bottom left of the tea cup, the conference paper is placed at 1cm from the meeting table. Generally, 2 pieces of paper are placed.Meeting.

7. Pen (usually a pencil): Placed on the top of each paper, the pen tip is in front, the slope is 45 , and the shop standard is up.

8. flowers: Put it according to the requirements of the guests, and the height does not exceed 30cm.

9, seat card: placed in front of each seat, 1cm above the Conference table.

10. Tea break: Put it according to the requirements of the guests (it is best to automatically persuade the guests to establish a tea break for the guests, and at least one waiter to provide services).Put paper towels, toothpicks, raw fruit plates, food discs, coffee cups, discs, coffee spoons, coffee stoves, sugar tanks, milk, Square sugar or sugar Bags.

Note: All items are required to be specified.

3. Conference table Place etiquette and conference services

1. Place etiquette

(1) The placement of the Conference table should be positive. The chair is placed in front of the Conference table and kept about the distance from the Conference table. The distance before the chair should be evenly about one person distance.To become a straight line.

(2) Put the manuscript paper on the Conference table according to the location of the chair. The manuscript paper is placed in the middle of the middle position of each chair.The nib is facing up, and the label was leaked.

(3) After the manuscript paper is positioned, the tea cup is placed above the right of the manuscript paper, and the distance is about a finger at the side of the manuscript paper.

2. Conference service

(1) The water starts from the right (the leader first, the clockwise sequential sequence), after pouring the water, the pot mouthDo not pour from the guest to the right.The podium must add water from the back of the guest.

(2) When adding water, if there is a covered cup, apply the little finger and unknown finger of the left handCracker the small balls on the cup lid, hold the cup with your thumb, index finger and middle finger, and end it from the deskTea cup, one after the other, pour the water into the cup sideways.

(3) If the guest work or talks, say "I'm sorry", and note when pouring the waterDon't be too full, it is advisable to be full of seven or eight points in the cup.Do not work too high, let aloneYou must cross the shoulders and heads of the guests.

(4) Do not lift the pot too high when continuing water, so as not to splash water.Don't stop the tea cupPour water directly or put the cup lid on the table.

(5) Renewal of water is generally carried out after 15-20 minutes in the event, and the venue is used at any timeWater situation.When you encounter the hot weather, you must add it at any time.The mouth is too high to avoid splashing out of the cup.Key points: Get up or rolled on the table on the cup lid, noCan be deducted, unhygienic, impolite.

(6) Choose the water time before the meeting starts, usually 5 minutes before the start of the meeting.

1. What kind of Outdoor table is easy to use

The outdoor folding table in the market has many styles and many types. To choose a good -looking Outdoor table, it is still more brave. Generally speaking, good Outdoor tables should meet the following requirements:

1. Material durable

Outdoor tables need to be used outdoors, so it is necessary to choose high -quality materials, and require high strength, light weight, good use of good use and stability.Generally, solid wood, steel, aluminum alloy and other materials are mostly used for Outdoor tables.

2. Pay attention to craftsmanship

The details are very capable of experiencing the quality of Outdoor tables. Good Outdoor tables are sprayed with plastic spraying, adding engineering plastic protection parts, and using card slot -type connections, which can improve their performance and service life, and it is also convenient to take care of it.

3. Stable use

A good Outdoor table requires stable bracket connection. What is more stable is the scientific triangle structure. It reasonably divides the stress area, the structure is stable, it will not shake at will, and it is super stable when placing heavy objects.

4. Easy installation

Some Outdoor tables need to be installed when they need to be used. If they are busy outdoors so that they are only for installing a table, it is too difficult. Therefore, be sure to choose a simple Outdoor table. The accessories are simple and clear.Poor people can quickly assemble or disassemble the storage.

5. High usage rate

Outdoor tables should be able to adapt to a variety of use environments, and some good Outdoor tables can be used in almost anywhere and in any scene.

6. Light and easy to carry

Outdoor tables should be carried out outdoors, so good Outdoor tables must be very light, easy to carry, and should not take up space.

2. Do you have to buy a folding style at the Outdoor table?

When buying Outdoor tables, most friends generally buy Outdoor folding tables. This Outdoor table can be folded when it is not in use, which is convenient for storage and does not take up space. In fact, Outdoor tables are not necessary to buy folding.

There are also Outdoor tables without folding. If there are courtyards at home, it is used in the Outdoor table in the yard. If you do nt bring it out, you can buy ordinary Outdoor tables.Not as good as ordinary Outdoor tables; if you often go out for outdoor activities, it is recommended to buy folding Outdoor tables better.

How to make homemade Outdoor folding tables

The outdoor folding table is light and portable, which is very suitable for outdoor activities. Now there are many Outdoor folding tables on the Internet. If you have a strong hands -on ability, you can also make an outdoor folding table yourself.Here are some ways to make several Outdoor folding tables:

Practice

1. Prepare the production materials and tools: wooden boards, electric diamonds, saws, tape measures, live pages hinges, nylon ropes, right corners, hammers, nails.

2. Cut the wooden board, use nails to set up a right -angle arched bracket with a nail, and insert a beam board at the middle height of the two standing feet of the bracket.

3. Make four shelf wooden frames, screw screws, and connect the shelf brackets through the live pages.

4. Drill the hole in the middle of the beam board. After entering the nylon rope, knots both ends of the rope head.

5. A pair of shelf desk brackets that are completed can usually be folded. When used, open a wooden board on it, which is a simple folding small table.

Two Practice

1. First make a small shelf in the rear.

2. Care on the desktop legs on both sides. Pay attention to the hollow and cut style of the table legs.

3. Fix the side plates of the table legs and the shelves with long hinges, and test whether it can be retracted freely.

4. Finally, the desktop and shelves beam are chain with long hinge (the reason why the side plate hinge is installed first and then installed the desktop to wrap the desktop legs).

Three

1. Saw wooden strips: 4 desk legs, 4 desktop support rods, 4 short fixed rods, and two long fixing rods (the thickness of two table legs is shorter than shorter).

2. The 4 tables legs are drilled at the intersection of the table you need, and the positions of the 4 holes should be consistent.

3. Drill the desk leg and the desktop support rod.The drill size is a little larger than the bolt.

4. Start assembled the desktop. First, use a short fixed rod with a short fixed rod and nail, and then nail the outer desktop legs and upper bolts.

5. When you put on the bolt, you will find that the bolt head of the table legs and the support rod protrudes, and the table legs cannot be merged. At this time, you need to use a large drill bit to drill out the holes and let the bolt head sink.

6. After installing the desktop, you will see that the top of the table's legs protrudes the support rod plane, so you must see the excess part, or you can't install the desktop.

7. Finally, fix the desktop with wooden screws to the desktop and complete.

Four

1. Prepare materials and tools: wooden boards, hammers, planers, and desktops are painted with paint -free ecological boards.

2. Seal the desktop edge, stick it with glue, knock gently, and press it tight.

3. The wooden strip line, planing flat, drilling, and then draw the thread, saw the position of the hoe, and punch.

4. Apply glue, then sting together, add wedge fixing.

5. The table legs and two windows can play a fixed role. One end of the table legs is connected to the desktop with a harmonious pages.

6. Add a wooden bar under the desktop to ensure that the table will not fall when the window support is not tightened.

7. Finally, brush the table legs with two layers of paint, which is convenient for cleaning in the future. A simple outdoor folding table is made.