Can the fishing rods be changed to the rock rod?

1. Can the Fishing rods be changed to a Big rod?

The performance of the radia poles is strong and is not restricted by the fishing point environment and in -depth, so now it is more and more loved by fishermen. It is not difficult to make a rock pole by yourself. Just pay attention to choosing a fishing rod.Is it a pole?

The unused table fishing rod can be modified slightly, which can be turned into a rock rod, but not all the Table fishing rods can be changed to the rock rods, otherwise even if it is done, it can not meet the requirements of the rock fishing performance. Generally, it can beChange the rock pole's desk fishing rod requirement:

1. The length requirements of the fishing rod

The size of the ingenic dance of the Izon fishing rod is between 100-115cm. This length is mostly for easy portability, because some of the rock rods cannot be collected back, which increases difficulty.Therefore, we choose to make the fishing rod of the rock rod. The contraction length should be between this size, not exceeding 120cm and less than 100cm.Generally, 4.5m, 5.4m, and 6.3m of Taiwan Fishing rods can be changed to Bigrdi. Among them, 5.4m is more suitable, and the 4.5m Taiwanese fishing rod is too short, which is not conducive to far away;The radia pole is too long to throw an arc, but at the same time, it also increases the load of throwing investment, the hardness of the hardness will increase, and the feel will lack.

2. Terminal requirements for Fishing rods

Some Table fishing rods are too soft. Even if it is changed to the rock rods, it will become "four dislikes". There is no performance of the rock Fishing rods, not as light as the hand rod, and the head weight is very obvious, and it is easy to break the fishing rod.Generally, you need to choose a hard fishing rod, such as 28 tuning, 19 tuning, etc.

2. How to change the fishing rod to the rock rod

There are mainly four parts of the radia poles. Two poles, rock rods, conductors, fishing wheels, and sealing rings. Here are how to change the fishing rod to the rock rod:

1. Seal all the guide ring and fishing wheel seat, install it on the fishing rod for debugging.According to the sealing ring, fishing wheel seat, sealing ring, and then to the guide ring.The conductor should be removed after the debugging of all Links in accordance with the principle of large and small.

2. Pour the glue of epoxy resin glue at a ratio of 1: 1. When adding a small amount of quartz sand, it is recommended to use a "hair dryer" to heat it in stirring, which is better.Then make the glue a little cold dry to prevent too thin and flowing glue.

3. The order of glue, follow the steps during debugging.Apply glue to the edge of the sealing ring, and put it up in the fishing rod.Apply glue to the inner circle of the fishing wheel seat, and then apply glue to the fishing rod position into the fishing rod. In the sealing ring, the handlebar fishery wheels have been completed.

4. Divide the original settings that were originally set, and then draw about 20 cm each section of the fishing rod, and then load them in the sequence of size.When fixing the glue on the ring, first apply the portal of the fishing rod, then put the inner glue inside the ring, and then put it on the mouth. The excess glue must wipe it clean to prevent sticking to other parts.

5. The top ring is not the same as other conductors. The top ring first applies the pole, and then use the "toothpick" to apply the glue to the guide ring, and the pole is slightly, and the squeezed glue is wiped clean.

3. precautions for changing rock rods in Taiwan

1. When modifying, be sure to choose the environment where the personnel do not move, because during the application of glue, there is no error in any link. Once there is less installation, the leakage rework is very numb, it is also easy to damage the fishing rod and the guide ring.

2. Squeeze out or stick the glue on the table fishing rod. You must wipe it clean.

3. After applying, the fishing rod should not be moved as much as possible, let the glue naturally dry and then use it.