How to wax on the skiing board, how to maintain maintenance skiing board

1. The importance of snowboard waxing

Snow plate wax is a wax that can adapt to a specific environmental temperature.When the snowboard is gliding, the bottom of the plate and snow are constantly rubbing, and the heat generated by friction will melt a small amount of snow, which formed a thin water layer between the bottom of the plate and the snow surface.If there is no wax layer protection at the bottom of the snowboard, the melted snow will penetrate into the bottom of the plate, causing damage to the snowboard.

Snow plate waxing is the most important part of the snowboard maintenance process.Waxing for the snowboard can enable you to enjoy the pleasure and random turn of skiing.At the same time, it will reduce the risk of damage to the surface and extend its life.Waxing can make the Ski board control more convenient, enhance the speed of the board on the snow, and make you turn easier.In this way, the endurance of your skiing can be more lasting.And waxing can extend the life of a snowboard and can protect the bottom of the plate.The new Ski panels are generally waxed, but after slipping once or twice, the factory wax is gone.

At the end of the snow season, the board wax must be sealed, and the boots on the fixed device are loosen to let the tight spring be in a "rest" state.The snowboard should be stored in a dry place to prevent the metal material on the edge of the snowboard to rust.Do not store the snowboard in the basement of the yin tide, or it may become a humid storage room due to rain.Snowboards that have been stored in a humid place for a long time may be deformed by the corrosion of the wood heart of the board due to inhalation of the moisture. Many slippery boards are caused by water and water corrosion.The seal wax on the bottom of the plate not only prevent the moisture from entering the plate, but also long -term storage can gradually penetrate the wax into the plate, so that the wax on the snowboard is more difficult to fall off when skiing in the coming year.

2. How to wax the Ski board

1. Before you wax the skiing board, make sure your skiing board is clean and dry, so that the board to absorb wax is convenient.

2. Slowly apply the wax on the skiing plate evenly, and adjust the electric iron to the temperature that can remove the wax without smoking.

3. Unless your skiing place is extremely cold, you can usually use any ordinary wax.It is recommended to buy an iron that is specially used for waxed, or find a hole without holes.Because unless the wax on the iron is completely cleaned, the clothes cannot be used with the same electric iron.

4. Be careful not to put the iron for too long in one place, because it may melt all the Ski panels.After applying it evenly, let the skiing board be reduced to room temperature and then continue. This process takes at least half an hour.

5. Use a hard plastic ruler to scrape the wax.Avoid using iron ruler to scrape wax, because this may hurt the Ski board, and it should be scraped along the direction of the head/tail when scraping the wax.

6. Finally, use a hard -plastic brush or a Baijie cloth to polish the bottom of the board, please continue to grind along the direction of the head/tail.

3. How to maintain maintenance skiing board

1. After returning from skiing, you must take out the snowboard from the bag, and wipe the snow on the snowboard with a soft cotton cloth or strong adsorbent paper to dry it.

2. After drying, see if there is any damage.If the plate surface is damaged, the snowboard can be placed flat. Remove the excess substances on the plate surface, ignite the prepared rubber strips and hold it horizontally, and drip the melting rubber strip on the scars of the snowboard to cool.

3. After cooling, scrape the excess rubber strip with a steel scraper. If there is a large area of damage, it should be repaired by professionals.

4. After returning from skiing, you should also repair the steel edge of the snowboard. First, use a knife with a golden steel to grind the blade and horizontal blade of the damaged blade, and then use the snowboard corner (The adjustable angle, the ideal angle is 90 degrees) along the plate to polish the steel edge. Finally, the traces left on the steel blade with the polishing process with the golden steel stones.

5. Pay attention to waxing the snowboard. At home, you can directly apply liquid or paste wax to the snowboard, or directly use the block wax on the surface of the plate.In minutes, use the plate surface to polish and polish it, so that the wax can be better attached to the plate surface.Or find a professional to wax the Ski board.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is valid. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt; error correction & gt; & gt;