The wonderful use of sawdust on flowers

1. The bandaging matrix of high branches

In the Meiyu season, the growing plant branches that were growing last year were selected to peel the ring 10-15 cm from the top of the top, and then wrapped in plastic Bags.Tighten the end, and then place the pot flower in the half -yin and half -yang to carry out daily maintenance management.You can take root in 2 to 3 months. After rooting, you can cut the mother plant into a new flower seedling.

2. The rooting matrix of plant cutting

Take a plastic film with a slightly longer height and a certain length, and spread the wet sawdust (pinch without dripping water), and then press the cuttings at a distance of 2 to 3 cm.~ 2 cm.Finally, it is tightly rolled, and every 10 to 20 cuttings are tied, each tied with large plastic film Bags, and tightened the bag to moisturize.Because the humidity is easy to control, the hair root is fast.

3, fat

Mix and mix with human dung urine, dress with plastic Bags, tighten the bag, place it at the temperature of 30 C to 35 C, and ferment and rot after 1 to 2 months.After fermentation and rotten sawdust, the nutrition is comprehensive, which will not make plants be nitrogen -deficient in phosphorus and potassium, and the texture is loose, and the dry and wet is moderate. It is a simple soil -free cultivation material, especially suitable for potted bamboo and orchids.After the fermentation and disinfection, after adjusting the acidity and alkali, the substrate of transitional cultivation after the test Tube seedlings is out of the bottle. The effect is as good as the perlite powder.

4. Made into Nutritional soil

If the sawdust is placed directly in the Flower pot, fermentation in the Flower pot will cause the flower root system to burn. Therefore, the sawdust needs to be placed in a plastic bag and add an appropriate amount of water.Its natural fermentation, about 3 months of sawdust rot into dark brown, can be used to cultivate flowers.

How to use the fermented sawdust

When the soil is equipped, you can add one -tenth of the fermentation sawdust, or it can be covered on the surface of the soil for flower Fertilizer in the later stage.

precautions for sawdust can raise flowers

1. In late autumn and winter, the temperature decreases. At this stage, most of the potted plants are mainly based on the cold prevention and warmth of the winter. At this time, fertilization can not be applied at this time.

2. There are no rotten things, including sawdust, not suitable for Fertilizer for flower plants. If it is placed in a Flower pot, it will produce the root system of the plants during the fermentation process, which will cause rotten roots of yellow leaves and other states.If you appear, it will be lost.

3. When sawdust fermentation, generally 20 days of fermentation in summer, fermentation of two or three months in spring and autumn, the fermented sawdust color will change from white to brown.Used.If there is not much sawdust, put it directly into the plastic bag, it will ferment.

1. cutting technology of Japanese red maple

1. Cutting time

The time of red maple and tender branches should be selected in summer and autumn, that is, from June-September, it can be available.

2. Cutting cuttings

The selection of red maple cutting is recommended to choose a half-wood rough branches with a diameter of 0.5-1 cm. The length of each section is about 10 cm. The upper end of the branches is retained with 3-4 leaves.The leaves are cut off 1/3, so that water evaporation can be reduced as much as possible.The cutting base should be cut into a 45 -degree section, and then put it into a moderate rooted water for half an hour to speed up the rooting speed of cutting after cutting, shorten the rooting time, and increase the root rate.

3. Cutting process

After the cuttings are treated, insert it into the peat soil or vermiculite, and then place it in the shade of it and do it.If it goes well, it can be transplanted at a maximum of 1 and a half months, and the survival rate is about 80 %.

Second, Japanese red maple breeding method

1. Humidity control

After the cuttings are completed, they will be poured once immediately. This will not only make the cutting base of the cuttings closely in contact with the soil, but also increase the humidity of the soil.After that, the amount of watering should not be too large, and water accumulation should be avoided, otherwise it is easy to cause corruption and death at the base of the cuttings.Under normal circumstances, spray water 2-3 times a day, and can be increased to 3-4 times under high temperature conditions.

2. Cooling treatment

If the temperature is too high, it will affect the growth of the plant and even burn the seedlings, so it is necessary to take a good shades to avoid direct light.At the same time, in order to achieve the cooling effect, it can increase ventilation and combine the method of water spraying to achieve the purpose of cooling.

3. Adjust the light

Because the insertion is still very fragile, the light cannot be strong, otherwise it is easy to burn the branches due to high temperature.Therefore, we need to use the Shading net for the Shading of the branches, which can reduce the strength of the light; the family potted plants can be placed in the sun in the early morning and dusk in the sun to receive the light.When the young plant is rooted and stable, the light time and strength can be appropriately increased every day.

4. Breeding soil

Japanese red maple is suitable for grown in loose and breathable and slightly acidic soil. It can choose humus soil rich in humus and well drainage for breeding.We can also apply a certain amount of base Fertilizer in the soil, which can increase the fertility of the soil.

5. Pruning management

During the process of breeding the Japanese red maple, the plants need to be trimmed regularly.Before trimming, you need to use alcohol cotton cloth to wipe and disinfect the trimming Tool, and then cut off the plant that grows over or too densely. After trimming, you can apply plants on the wound.

3. precautions for Japanese red maple breeding

When we cultivate Japanese red maple in winter, if the ambient temperature is lower than 10 C, the plant will be frostbite, which will affect the normal growth of the Japanese red maple.Therefore, when the temperature is relatively low, you need to keep warm for the plant. You can use a grass cushion or cotton cloth to wrap the plant.At the same time, it is necessary to stop watering or fertilizing, so as to make the Japanese red maple spend the winter smoothly.

What is a Wall lamp

Washing wall lamps, as the name suggests, let the Lights wash the wall like water, mainly used for building decoration and lighting, as well as outlines for outline large buildings. Becauseled It has the characteristics of energy saving, high light efficiency, rich color, long life, etc. Therefore, other light sources with wall lamps are gradually being led Washing lamp instead, led The technical parameters and the technical parameters of the Wall lamp lamp lamp led The lamps are generally similar.

The manufacturing step of the Wall lamp lamp

1. First apply a bit of heat -conducting glue on the intact aluminum -based plate, which can help the wall washing the heat sink to dissipate heat, and then put the lamp beads on the ground welded one by one.

2. Put the shell of the wall washed on the welded lamp bead and seal the two grooves next to it.It is convenient for gels when it is filled with glue

3. Those who need to irrigate are the easier -drying silicone (white gel or vinyl) that is easy to dry into the Wall lamp.

4. After these silica gels are dry, check the lamp beads carefully if these glue is covered.

5. Just cover the glass of the Wall lamp and put it on the head.Water washing lamp is made like this.(These lines must be connected in the head of the group before the group head)

6. The last link is aging packaging.

How to install the Wall lamp

1. Do the work before installation according to the position placed by the power supply;

2. Fix the lamps with screws firmly;

3. Connect the lamp with the power cord firmly, and wrap the waterproof tape without the wire head;

4. When installing the wiring, a branch power supply is connected to a maximum of 8-10 wall lamps; or after 50 meters, connect another power cord.

5. After the installation is completed, please check the installation line to confirm that the installation is correct. After no electrical short circuit, the corresponding control power supply is connected;

6. If there is a problem in installation, please consult our technical personnel.Or log in to the Website of lighting Enterprise lighting directly

What is the general height of the Wall lamp in different positions?

1. General Wall lamp installation height, that is, 2240 ~ 2650mm from the ground.The Wall lamp in the bedroom is closer to the ground, about 1400 to 1700mm.The distance from the Wall light to the wall is about 95-400mm.

2. The height of the Wall lamp in the corridor and the corridor should be slightly more than 1.8 meters high, that is, 2.2 to 2.6m from the ground.

3. If the Wall lamp in the working environment is 1.4 to 1.8m from the desktop, the Wall lamp on the bedside bedside is about 1.4 to 1.7m.

4. The distance of the Wall light is about 0.09 to 0.4m.

Where is it suitable for installing Wall lights

1. bedside

Because it is auxiliary lighting, the bedroom bedside needs the help of wall lamps, because the bedroom generally needs auxiliary lighting decoration. The Wall lamp installed on the bedside, it is best to choose the light head to adjust the direction.The style of the Wall lamp should be considered to echo the bedding or curtains in order to achieve a better decorative effect.

2. Corridor or living room

In addition to the bedroom requires auxiliary lighting, the general living room and the aisle are also needed to be used for assistance lighting. The lamps in these places should generally be soft, and the installation height should be slightly higher than the horizontal line. It is best to match it when used in use.Some other decorative objects, such as: an oil painting, a vase with flower arrangement, or a wall frame displayed by a artwork, etc., the effect of decoration is more delicate.

3. Before the mirror

In addition to the two spaces require Wall lamp for assistance lighting, the Mirror front light in the bathroom space can also be selected for installation. The Wall lamp installed in front of the bathroom mirror is generally installed above the toilet mirror.The style of the style can be considered to echo the handle of the faucet or the bathroom cabinet.

4. Restaurant

For small apartment types, in terms of lighting, only local lighting is often required to create a comfortable feeling. For example, a small apartment restaurant, if you choose a chandelier to decorate, the light may be too bright and dazzling, and the Hanging downThe Hanging chandelier will make the compact space more crowded, and choosing one or two restaurant wall style and color -shaped wall lamps to decorate will make some decorative scenery.When choosing a Wall lamp, you should pay attention to matching the color of the wall. It is best not to choose the color of a color system with the wall. Use some contrasting color wall lamps to sometimes have a good effect.

What are the installation steps of the Wall lamp?

1. Determine the installation location

First of all, we must determine the installation position of the Wall light on the wall, and generally determine the specific location according to the differences in functional space.For example, the bedside bedside lamp is usually between 1400 mm and 1700 mm from the ground height, while wall lamps such as balcony and aisle are often higher than that of human vision, about 1.8 meters.In fact, there is no specific restrictions on the height. Everyone can determine the installation location according to their actual situation.

2. Tag number on the wall

The position of the Wall lamp is mainly determined the position of the Wall lamp seat. When you are determined, you must make a mark on the wall and draw the holes on the Wall lamp Hanging plate to facilitate the expansion screws.

3. Use electric drill drilling

Before drilling, you should understand your own line layout diagram to avoid hitting the wires when drilling, and then use the electric drill to punch the marked mark. At the same time, pay attention to the depth of the drilling.Generally, it is advisable to not exceed the length of the expansion screw.

4, upper expansion screw

After playing the holes, insert the expansion screws into the hole, and use the hammer to hit the expansion screws into it until it does not enter the wall.

5. Install Wall lamp Hanging board

Install the Wall lamp Hanging board, fix it on the expansion screws with screws, and pay attention to the alternation of both sides when screwing, which can prevent the screw from shift and keep the Wall lamp Hanging on the level and not skew.

6. Install the lamp body

First install the Hanging panel and the suction plate with screws, tighten and fix, then disconnect the power, connect the wire of the Wall light with the power cord, and finally install the lamp body.Pay attention to check immediately after the installation is completed to see if it can be used normally.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is effective. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt;Correction & gt; & gt;

[Barracks] Outdoor Barbecue oven size Barbecue oven purchase points

Outdoor Barbecue oven size

You can choose the size of the barren ovens based on the number of people who are suitable for different travels.If you have thought about the little couple of the two -person world, then choose the length width height191915cmThe mini -Outdoor barbecue will be very suitable. Generally, there are two slices of barbecue nets. When you go out, you can go out to barbecue and grilled vegetables.;;If the number is5Within people, you can choose long width height in483923cmThe left and right Outdoor barbecues are larger and the grill is larger.;;if8~12When people dine, you can choose long width height in726730cmIncreased Outdoor Barbecue oven.

barbecue overtwin guide guide

Consider whether the barbecue is portable.Outdoor barbecue is our own items, so it is best to consider this problem when buying, which can facilitate us to carry. This can bring us a lot of convenience. It is recommended to choose the kind of folded barbecue here.furnace.

Buy according to the material.There are many materials for barbecue stoves on the market, and the price is different. It does not have to be expensive, but the use of iron barbecue stoves is definitely not long. Therefore, it is recommended to choose the stainless steel, which is stronger than the iron system.Durable and not easy to rust.

Buy according to the size of the Barbecue oven.Someone must think that the smaller the portable, the better, but it is also necessary to consider the factors of the number of barbecue people. Therefore, when purchasing, you can determine the size of the grill according to the number of barbecue people, so that everyone can eat delicious barbecue.

Whether to carry oil and smoke.When barbecue, the meat will drip oil, and the oil dripping on the high -temperature stones will smoke, and the smoke will make a bad taste on the food.Therefore, the stove should have some kind of equipment to catch the oil, and then let the oil flow outside the stove.

Whether there is a thermometer.I often see how long to bake in barbecue recipes. If there is no thermometer, it can only be guess. It is difficult to determine whether the food is cooked.

barbecue is definitely not prepared for ingredients, and many meat foods will be more delicious after marinating.Xiaobian will share a recipe for barbecue pickled sauce: pour into 13 incense in the container100Gick, refined salt36Gram, MSG70gram((Do not have too much MSG, it will cover the original umami flavor of the meat quality ingredientsCure, A little olive oil, ginger and shallot40Gram, white sugar7Gick, red summer starch250Gich, friends who like meat pine flavor can join25Gram's pine powder.The above isI want to introduce the size of the Outdoor barbecue and purchase guide that I want to introduce to you, hoping to help everyone.