1. How to raise yellow shrimp flowers

1. Grow the soil Yellow shrimp flowers like to grow in light loam soil. Potted soil should use rotten leaf soil, rivers and sand soil, and rural soil to ensure that the soil is loose, breathable, drained, and nutritious.Before the basin, disinfect sterilization once, while adding an appropriate amount of Organic fertilizer to improve soil nutrients.

2. Light temperature conditions In the warm environment, the growth rate of yellow shrimp flowers is relatively fast, so it is better to stabilize the temperature at about 23 C.Especially in the two seasons of winter and summer, when the climate is relatively extreme, do a good job of regulation.

3. Water Fertilizer irrigation Watering and fertilization are one of the most direct ways to obtain nutrients for yellow shrimp flowers.While keeping the soil moist, water does not occur.During the growth period of thin Fertilizer, every 20 days, the diluted thin Fertilizer liquid must be applied to the main need to meet the growth of yellow shrimp.

Second, the cutting method of yellow shrimp flowers

Each yellow shrimp flower stem and branches have a pair of submarine axillary buds. The axillary buds in the middle of the branches are mature and strong. Cut the cuttings about 3 to 4 cm long and insert it in the seedbed or insert;The axillary buds are germinated and growing; can be planted in pots after one month, and the survival rate can reach more than 95%.(Note: Choose a strong two fork seedlings on the basin.)

Third, how to trim yellow shrimp flowers

Potted yellow shrimp flowers can cut pruning, and it is necessary to cut pruning during management. Branching is generally selected in spring or autumn.In spring, the yellow shrimp flower draws new branches and leaves. It should be trimmed off in time, and the sick and old branches should be trimmed off in time.autumn is the flowering period of yellow shrimp flowers. After the flowering period, cut off the residual flowers to reduce nutrient consumption and promote it to recover as soon as possible.If you are in the seedling stage, you need to talk about it in time to control its height.

1. What are the use of swimming storage packages

The swimming storage bag is a Swimming bag that we often say. It is a bag used to store all kinds of items required for swimming. Friends who often swim often buy a swimming storage bag. So what is the role of swimming storage Bags?

1. storage: The Swimsuit, swimming hats, swimming training equipment, toiletries, normal clothing, etc. of the swimming, can be put in the swimming storage package, and the classification is well stored, which is neat and easy to use and stored.

2. waterproof: swimming is underwater exercise. After the completion of the Swimsuit, towels, etc., it is wet in the bag. It will be easy to spill in wet water directly.Prevent wet clothes from wet and dry clothes.

3. Other purposes: In addition to swimming, there are many other uses for swimming storage packages, such as putting it at home as Hanging storage Bags; going to the gym for fitness packs; traveling or traveling on a business trip.

2. How to install a Swimming bag

You can put a lot of things in the Swimming bag. In order to facilitate use, you can use some tips when storing. There are two main points of storage skills for swimming storage packages:

1. Packing from bottom to top

When you put things in the Swimming bag, you can put it from bottom to top. Below is usually shoe and warehouses, first put the shoes in; then put different things into the small partition layer, then put the washing products in the bag in the bagThen put the towels and Swimsuits on top, so that if there is a toiletries leak, you can avoid wetting other things; put electronic equipment and paper things on the upper layer.

Do not store the wet area when you are loaded. The wet area is a wet Swimsuit after swimming. Of course, if the space is not enough, you can also put the Swimsuit directly in the wet area. Before you put it, pay attention to whether it is dry.

2. Pack up the Swimming bag in advance

The swimming packaging the first night when going out to swim, so that you can avoid the hands and feet in the next day; put the bag beside the door or shoes after installing it to avoid forgetting to carry when you go out.

1. How to remove the hook glue

Usually use hook glue, and after a long period of time, the hook glue is removed. At this time, the hook rubber printing will appear in the fit part, which will affect the beauty of the fit part. At this timeIt is obvious, you can apply more, and then use a small shovel to linked the hook printing.

White vinegar contains organic solvents, which can dissolve the polymer ester in the hook glue, which can easily remove the hook glue.

When using white vinegar to remove the hook rubber printing, do not dosage too much. The acidity of white vinegar is harmful to the walls and other places. If you apply too much, it may destroy the material of the fit part and make it show other colors.

two,How to remove the traces of sticky hooks

If there is no white vinegar, you can actually use wind oil essence,Alcohol,acetone,Hand creamWhen it is replaced by items, the effect is similar, and it can be removed in time.

1. Wind oil essence

Pour the wind oil on the tissue and wipe the residue with a paper towel.

2,Alcohol

Pour some alcohol on paper towels (the best industrial alcohol, can also be medical alcohol), the method is the same as wind oil essence.

3,Patthon or nail washing water

The amount of acetone used in this method is small, and it can quickly remove the residual glue, which is easy to completely remove the residual glue, which is more troublesome.

4,Hand cream

Squeeze the hand cream on the residue, and slowly rub with your thumb, you can slowly rub the sticky stubborn glue, but this method is slow and laborious.

1. Troubleshooting device fault characteristics

Failure 1: After installation, the headlights work normally, but the instrument Taiwan big light fault alarm Lights are on

This is a very common failure. It may be because the pyrine lamp and the stabilizer are not matched. You should choose the same voltage of the pyrine lamps and stabilizers.

Failure 2: After installation, the Light bulb has a flashing flashes or often off or the left and right Lights.

Most of these causes of failure are line problems, which may be caused by the stability device's start -up current.At this time, the working current of the headlight line needs to be checked normally.

When the stabilizer squeaks in the work, this is the sound of the transformer work inside the stabilizer. This situation is normal.However, the sound is too loud, and the cover can be heard outside, it means that there is still a quality problem in the transformer. Please rest assured that this will not affect the use. If it is serious, replace the stabilizer.

2. Method of determining whether the stabilizer is damaged

1. When the lamp is not bright, twist the Light bulb to replace the new Light bulb. If the new Light bulb is on, it is the problem of the bulb; if it is not bright, there is a problem with the stabilizer.

2. Check the interface of the stabilizer line beam. If the socket has a loose or a problem with the line, the stabilizer will fail; if the plug is normal, it is the problem of the stabilizer.

3. How to detect good or bad on the airlight lamp

1. Bullet test

(1) Different way

a. Whether the electrodes of the two ends of the light ball have a serious loss.

b. Whether the ceramic Tube has broken and broken.

c. Whether the visual wire wire is broken.

d. Whether the visual lamp Tube is broken and damaged.

e. Whether the lamp Tube column is broken and broken.

f. Whether the visual lamp is loosened or not.

g. Whether the base is loosened and falling off.

h. Whether the Light bulb power line has a loose and falling off.

i. Whether the light ball has cracks or rupture.

(2) Test method

a. Take a good Ballast as the benchmark for testing HID Lights.

b. Prepare a power supplyer and adjust its voltage to 13.20V as the test benchmark voltage.

c. Pick up all wiring first and turn on the power supply to test whether the Light bulb will light.

d. If the power is turned on and cannot light up the HID light, it means that HID is damaged.

2. Stability device test

(1) Different way

a. Whether the visual power line group is destroyed or damaged.

b. Whether there is a destruction or damage to the visual control line group.

c. Whether the high -voltage line group is destroyed or damaged.

d. Whether the high -pressure box line group is damaged or damaged and leaked.

e. Whether the body of the stabilizer is destroyed or damaged and leaked.

(2) Test method

a. Take a good HID light as the benchmark for testing Ballast.

b. Prepare a power supplyer and adjust its voltage to 13.20V as the test benchmark voltage.

c. Pick up all wiring first and turn on the power supply to test whether the Light bulb will light.

d. If the power is turned on and cannot light up the HID light, it means that Ballast is damaged.

e. If you turn on the power to light up the HID light, it means that Ballast can light up, but you need to check how much its power input current is to determine whether the function of the stabilizer is normal.

The determination benchmark is as follows:

Normal input current range between 3A-5A.

Greater than 5A indicates that the work efficiency of the stabilizer is reduced, resulting in increased consumption power and decreased reliability.

Smaller than 3A indicates that the work efficiency of the stabilizer and the decrease in reliability may cause the Lights to light up.

First, the sky -to -scaling canopy is good or butterfly.

Three -piece set of indispensable Camping: tents, sky curtains, tables and chairs. The combinations of these three are always exciting. If you are well matched, the style of the entire Camping atmosphere will suddenly sublimate.What about it?

In terms of sunshade area and windproof ability, the butterfly shape is the best.Of course, this is also related to personal aesthetics.If you prefer Square ones, you can buy a Square sunbath canopy.

2. Can the sky curtain Tent be built in the cement floor?

Whether it is used to cover the scorching sun or cover the wind and rain, the sky curtain is very applicable. Compared with the Tent, the construction of the sky curtain is more difficult, and the construction of the sky curtain has no fixed style. It can be selected according to the venue, conditions, weather, and personal preferences.So can the sky curtain Tent be built in the cement floor?

The sky curtain is fixed by the role of ground nails and wind ropes. The cement ground nails are generally not tied, so it is best not to choose to build the sky curtain in the cement ground.The venue suitable for the construction of the sky is:

1. It is easy to tie the place where there are trees. You only need to tighten the rope. The position of the drain of the drainage outlet can be left.

2. If there are no trees, the railing is very good, rely on the railing to pull the rope, a little loose rope, use the sky curtain to support the sky curtain, and tighten the rope.

3. The beach tie the sky curtain, the support rod is easy to insert into the sand, so that the sky curtain is loose. You can use the mineral water bottle to insert the pole in the bottle and then use it.When the water is used again, the sand is tight.The beach can be used with a barbecue fork, stepped off the fork with your feet, and the long rod is easy to insert. The fork can also be used as a ground diced in a hard place.