1. Troubleshooting device fault characteristics

Failure 1: After installation, the headlights work normally, but the instrument Taiwan big light fault alarm Lights are on

This is a very common failure. It may be because the pyrine lamp and the stabilizer are not matched. You should choose the same voltage of the pyrine lamps and stabilizers.

Failure 2: After installation, the Light bulb has a flashing flashes or often off or the left and right Lights.

Most of these causes of failure are line problems, which may be caused by the stability device's start -up current.At this time, the working current of the headlight line needs to be checked normally.

When the stabilizer squeaks in the work, this is the sound of the transformer work inside the stabilizer. This situation is normal.However, the sound is too loud, and the cover can be heard outside, it means that there is still a quality problem in the transformer. Please rest assured that this will not affect the use. If it is serious, replace the stabilizer.

2. Method of determining whether the stabilizer is damaged

1. When the lamp is not bright, twist the Light bulb to replace the new Light bulb. If the new Light bulb is on, it is the problem of the bulb; if it is not bright, there is a problem with the stabilizer.

2. Check the interface of the stabilizer line beam. If the socket has a loose or a problem with the line, the stabilizer will fail; if the plug is normal, it is the problem of the stabilizer.

3. How to detect good or bad on the airlight lamp

1. Bullet test

(1) Different way

a. Whether the electrodes of the two ends of the light ball have a serious loss.

b. Whether the ceramic Tube has broken and broken.

c. Whether the visual wire wire is broken.

d. Whether the visual lamp Tube is broken and damaged.

e. Whether the lamp Tube column is broken and broken.

f. Whether the visual lamp is loosened or not.

g. Whether the base is loosened and falling off.

h. Whether the Light bulb power line has a loose and falling off.

i. Whether the light ball has cracks or rupture.

(2) Test method

a. Take a good Ballast as the benchmark for testing HID Lights.

b. Prepare a power supplyer and adjust its voltage to 13.20V as the test benchmark voltage.

c. Pick up all wiring first and turn on the power supply to test whether the Light bulb will light.

d. If the power is turned on and cannot light up the HID light, it means that HID is damaged.

2. Stability device test

(1) Different way

a. Whether the visual power line group is destroyed or damaged.

b. Whether there is a destruction or damage to the visual control line group.

c. Whether the high -voltage line group is destroyed or damaged.

d. Whether the high -pressure box line group is damaged or damaged and leaked.

e. Whether the body of the stabilizer is destroyed or damaged and leaked.

(2) Test method

a. Take a good HID light as the benchmark for testing Ballast.

b. Prepare a power supplyer and adjust its voltage to 13.20V as the test benchmark voltage.

c. Pick up all wiring first and turn on the power supply to test whether the Light bulb will light.

d. If the power is turned on and cannot light up the HID light, it means that Ballast is damaged.

e. If you turn on the power to light up the HID light, it means that Ballast can light up, but you need to check how much its power input current is to determine whether the function of the stabilizer is normal.

The determination benchmark is as follows:

Normal input current range between 3A-5A.

Greater than 5A indicates that the work efficiency of the stabilizer is reduced, resulting in increased consumption power and decreased reliability.

Smaller than 3A indicates that the work efficiency of the stabilizer and the decrease in reliability may cause the Lights to light up.

1. What is the flashing light?

Blasting Lights, also known as the frequent flashing light, use electronic means (such as programming single -chip microcomputer IC, etc.) to make the light source flickering slowly or quickly to play a warning.The flashing light has been used on the police car before, rarely used in the people. This kind of policeburstThe flashing Lights belong to the controlled items.It is now widely used in entertainment venues, road traffic, advertising brightening, vehicle ships, public security police and other fields.Although the state has no mandatory requirements for the installation of flashing Lights, it cannot be used in the state or city.

2. What are the uses of flashing Lights?

1. Basic role

The role of flashing is to remind and warn. For example, if you have an emergency, you need to attract the attention of others. You can explode, so others will notice you.For a simple example, it is at night when you stop the car on a high -speed car. It is happening at night. You can explode the car after the flash warning. Of course, you cannot shoot the driver's cab.During the fire, he was trapped in the house and flickered to remind people outside to save himself.Flashing can also cause dizziness. There is a certain self -rescue function. There are not many opportunities for daily use. It is useful at critical moments.

2. Modified family

With some low -frequency flashing small power decorationburstFlash lamps appear in the car supplies market, and many lovers who love modification willburstThe flashing Lights are one of the essential weapons for the car -loving modification.

3. Daily necessities

There are many LED pocket -shaped flashlights on the market, which is very suitable for enthusiasts who like wild activities.The shell of metal alloys has the function of strong light, work light, and flashes. LED is energy saving, environmental protection, long life, and convenient to use, and the continuous lighting of this flashlight is very long.It reaches 8 hours, and the work light is 19 hours, and the brightness of the work is also very bright.

1. What is a single -arm street light

There is only one light pole of the general lighting street light. On the top of the light rod, a branch arm is equipped with a lamp head to provide public lighting. We call this street lamp as a single -arm street lamp, also known as single -arm light.Single -arm Lights are divided into ordinary sodium lamps, single -arm street lights, energy -saving lamp single -arm street lights, pyrine single -arm street lights and LED single -arm street lights.

Single -arm Lights are the most common type in road Lights. There is only one arm. The pole body uses Q235 low -carbon high -quality steel bending welding at one time. The weld is Smooth and Smooth.The appearance is beautiful, simple and Smooth, and is usually installed on both sides of the river, slope, or wider road surface to play a role in lighting road conditions and guiding safe driving.

2. What is the lamp of both arm street lights

Both arm lamps are derivative lamps of single -arm street lights, that is, two branches on the top of the light pole, two lamp heads are installed, and the roads on both sides are illuminated.

The two branches of the arms have a certain symmetry, which is more abundant than the shape of a single -arm light. Generally, it is installed on a multi -away green Belt or a road section with special lighting requirements.energy.

What is the difference between one -arm street lamp and binocular street lights

1. Different shapes

The main difference between single -arm street lights and arms street lights is the shape. Single -arm street lights are one arm, and the top of the light rod of the arms street lights has two branches, and it is symmetrical.The street lights are more beautiful.

2. Different installation environment

Single -arm street lights are suitable for wider roads such as residential areas, rural roads, factories, parks, etc., and both arm street lights are mostly used on the two -way roads on the road and some special lighting road sections that need to take into account both sides of road lighting at the same time.Essence

3. Different costs

Single -arm street lights only need to install one branches and one lamp head. The installation cost is definitely lower than the arms street lights. However, in terms of use, the arms street lights can take into account the roads on both sides with only one light pole.Installed on both sides, generally, the arms are more energy -saving and environmentally friendly.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is effective. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt;Correction & gt; & gt;

1. What are the guard lighting Lights

The lighting source should adopt various high -efficiency energy -saving fluorescent Lights and incandescent lamps.It should also meet the requirements of lighting places, color rendering, and anti -glare.

2. How to set guard lighting

1. The air defense basement should have normal lighting and emergency lighting at the normal and wartime lighting. Usually lighting should also have duty lighting, and transitional lighting should be set at the entrance.

2. The light -defense basement of the Pingli war should be determined according to the following requirements:

1. The illumination of normal lighting should be determined by referring to the illustration standard of similar ground building.It is necessary to adhere to work with high visual requirements for a long time, which can appropriately improve the degree of illumination standards.

2. Lantern and its layout should be coordinated with the function and building decoration;

3. lighting or emergency lighting that can be controlled alone in normal lighting should be used in normal lighting.

3. The transition illumination of the air defense basement should adopt a natural light transition. When the natural transition cannot meet the requirements, artificial lighting transitions should be used.The transitional lighting should meet the needs of people in and out of the basement in sunny, cloudy days, and night personnel.The current of each lighting single -phase branch should not exceed 16A.

4. Two AC220V10A single -phase three -hole splash -proof sockets should be provided with a cleaning room and inspection room.

5. At 1.5m from the ground near the sampling point of each filter absorber in the filtration room, 1 AC220V10A single -phase three -hole socket should be set.

6. Medical ambulance engineering, professional team members covering part, and first -class personnel covering the anti -communication duty room shall be set up in the AC380V16A three -phase and four -hole sockets, one circuit breaker, and 7 AC220V10A single -phase three -hole sockets.

7. Anti -ization communication room of the second -class personnel should be set in the AC380V16A three -phase and four -hole socket, one circuit breaker, and 5 AC220V10A single -phase three -hole sockets.

8. The anti -chemical equipment storage room should be set with 1 AC220V10A single -phase three -hole socket.

9. The selection of lamps should be selected with a lighter line Hanging or chain chandeliers and bayonet lamp heads.When the indoor net height is low or the usual needs are used to choose the ceiling light, the defense drop protection network should be added during the war.

10. The lighting of the passage, entrances, and public rooms and room lighting should be powered by different circuits.

11. The lighting power circuit from the protective area to the non -protective area. When a power circuit is shared in the protective area and the non -protective area lamps, a short -circuit protection device should be set on the inside of the protective closed door and the inside of the linked Battle.The lamps in non -protective areas are set up separately.

12. At the time of war, the main entrance and exit of the closed door to the channel lighting power supply from the ground to the ground should be supplied by the human electrical anti -power source cabinet within the protective unit. It is not advisable to use the power system power supply.

[Gong Lantern] What is the palace lamp?

What is the palace lamp

The palace lantern began in the Eastern Han Dynasty and flourished in the Sui and Tang dynasties. It has a strong local characteristics. The palace lamp as the name suggests is the lamp used in the palace.It is famous for its graceful and luxurious and full court.Due to the long -term palace, in addition to lighting, it is also equipped with fine and complicated decorations to show the wealth and luxury of the emperor.The orthodox palace lamp is in star anise, hexagonal, and four -corner. The contents of the drawing screens on each side are mostly dragons and phoenixes, Fushou Yannian, auspicious Ruyi, and so on.

Palace lantern practice

Skeleton

The relatively simple shape of the paper lanterns is cube or cylindrical body. It is best to use the bending bamboo branches or bamboo Skin to form a frame.If it is not easy to find, the slender hard cardboard and the bamboo sticks for barbecue can also be lacking strong and flexible, but it is also a very good decoration in the room.

Make a lamp body

Buy a few pieces of white, red ordinary rice paper or sprinkled gold rice paper in the four treasure shops of the Wenfang, which is cut into the length and width that conforms to the lantern skeleton, and you can design the pattern on your own.Calligraphy, painting, and paper -cutting can all show their style on the small lanterns.After being good, you can also use the narrow strip paper upper and lower edges, which look more elegant, very much like ancient palace lamps.If you are not good at calligraphy and calligraphy, there is a simple way for reference.Use a piece of paper to draw the words you want on the post, and then overlap this thin paper and dark red rice paper together, and dig the handwriting with a single -edged blade.Remove the thin paper, and the hollowed handwriting appeared on the red propaganda paper.Use white rice paper to make the lamp body, the red mission paper pastes inside, the candlelight or light is mapped from the hollowed out, the effect is quite beautiful.

Make light source

If you put it indoors, you only need to light a ordinary candle in the lantern; if you want to carry it out, it is best to use a Light bulb and battery to make a simple circuit.