1. How to wear the curtains

1. Small pleated wear method

Put on 1, 2, 3, and 4, that is, the four-to-teeth hook's 4 inserted pins are inserted on the serial number 1234 hole on the cloth band, respectively.4 holes.

2. Mid -fold traditional wear method

Put on 1, 2, 4, and 5, that is, the four -to -teeth hooks are inserted into the target number 1245 hole on the cloth zone, and 1 hole is separated by the interval, and the third fork is worn; the two hooks are separated by 4.-6 holes, generally 7-8 miracles per meter.

3. South Korean wear method

You can also wear two more than one, and you can also wear two more, so the effect is more prominent, but the more the amount of the cloth is used. After the hook is put on to the bottom of the cloth Belt, the hook is tied.Fold the folds so that it is facing the front. In actual use, you can adjust the number of inserted places inserted into the slot.

4. Big pleated wear method

It is recommended to wear 1, 3, 8, and 9, that is, the four -to -teeth hooks are inserted into the serial number 1389 hole on the cloth Belt, and 4 holes are separated by the middle of the middle.-8 holes.The folds of the curtains look a bit like a butterfly shape.

two,How to hang the curtain hook

1. First of all, find the position above the curtains, and observe it carefully. You can see the gap. It is a double -layer and there are special hooks.

2. Hang the hook in and pay attention to the position of the folds.

3. Leave the folds, then hung the hook completely and lift it up.

4. The hooks on the curtain rod are put on, and then the hook is prescribed later.

5. Gather the hooking place in one place to facilitate the hook.

6. Follow the sequence of the hook and hang the hook.

7. After Hanging up, the curtains are hung up.

1. Cable link model

General cable hooks are linked to mineral cables. The specifications are 20, 30, 40, 55, 70, 80, 100, and 5 hooks and 8 hooks.

<table style="width:80%;" cellpadding="2" cellspacing="0" align="center" border="1" bordercolor="#000000">

IA

hook length (mm)

Maximum tension (n)

8 2

166 2

4100

20 2

110 2

4100

30 2

122 2

4100

40 2

127 2

4200

50 2

144 2

4200

60 2

156 2

4200

70 2

167 2

80 2

189 2

100 2

209 2

84 2

40 2

60 2

77 2

table>

2. How many meters are the cable hook per meter

In the telecommunications engineering budget, the cable is hooked about 50cm to put one. To be precise, it is linked to 2060 cables per 1km.

ConstructionGenerally, one interval is 0.6-0.8 meters.

Third, cable hook installation method

1. Select the suitable cable hook according to the cable model and outer diameter. Every 1.2m to 1.8m (can also be limited to the cable is not drooped) as a suspension unit, each unit is linked to one or more cables according to one or more cables.

2. During the suspension, first fix the hook on the wall of the well. When the hook is fixed, the arc hook is vertically drooping when the hook is fixed.If multiple cable Hanging, one set of hooks and two skewers must be adopted.The construction personnel first connect the hooks on the ground, and then fix it according to the previous method.

3. When the two hooks are connected in series, first align one hook hole to align with another hook rod, press it hard, so that the Hanging rod enters the holes completely, and then rotate with the arc hook to make the two hook straight rod sections become sections.180 .

4. After confirming that the cable enters the curved hook as a whole, the construction staff can let go of the cable.

(1) Each unit can be linked in series and the number is not easy to exceed 10.

(2) In order to improve the quality of the suspension, the hooked straight pole segment is best to close the well -closed during static.

(3) It is strictly forbidden to quickly send the cable into the arc hook by the volley jumping method, which may make the curved hook to withstand the weight of the cable and the human body in an instant, causing a break.

(4) After confirming that the cable overall enters the curved hook, the construction staff can let go of the cable.

1. Is it better to hook the towel or be a rod?

Each has its own advantages. For example, a towel hook can be lined up with a few towels. Each towel does not take up a lot of positions, but it is not conducive to the dryness of the towel. If it is humid for a long time, the towel is easy to mold.For towel rods, you can flatten the towels, which is conducive to the drying of the towel. The towel rods take up space. The drying towels are too small. Consumers can choose according to their own needsEssence

two,Where to put a towel hook

1. Hanging on the side of the washbasin

Because peoples living habits are mostly placed on the side of the washbasin, the towels are best Hanging on the side wall of the washbasin in order to facilitate the use of the sideline.Install some towel hangers, especially for the main guards, if it is a bathroom used by two people, this is a very convenient method.

2. Behind the door

Because the door is not ventilated, in fact, many people do not like to put the towels on it. They may not be easy to dry because they are not ventilated. They can be installed and hooking at the back of the door to facilitate the use of the family for a long time.

3. The wall of the bathroom

Because the towels and wiping towels are some relatively small towels, and bath towels are usually relatively large, so we need to use a strong load -bearing capacity to put it near the white wall of the shower room.It will be more convenient when taking a bath.

4. The door of the bathroom

You can hang the towel on the handle of the bathroom door. The sliding door inside the towel Hanging the bath, and the handle of the sliding door on the outside. Although this method does not look beautiful, it is convenient.

1. High installation of clothes hooks

1. Xuanguan

You can judge according to your family's height, so that everyone can get items. Generally, it is better at about 1.6 meters.It should not be too low, so you need to bend over with things, and if the clothes and buns are too long, you will mop the floor.

2. bedroom

Like in the porch, the height is more convenient to get items. Now there are coat hooks that can be hung directly at the top of the door, and the door of the bedroom will not be particularly high, so as long as you do not install too low.It is recommended to be a little taller than yourself, so as not to accidentally hit the hook.

3. bathroom

The installation height of the bathroom hook is also very important.Generally speaking, the installation height of the bathroom hook can be determined according to the height of the family, usually with 10 mm on the basis of the minimum member height.Such height will be more convenient when using a coat hook.You can also install the hook on the right side of the mirror to make the towels more comfortable and convenient.

2. How to install the hook

1. Positioning

The installation position of the hook must be determined, including width and height.There are single -clothes hooks and row hooks. When installing a single hook, a few clothes hooks are usually installed into a row of combinations. ThereforeThe width of the installation surface is reasonably calculated, and the distance between the single hook is divided to ensure the beauty after installation.The rowing hook does not have a width trouble. As long as the width of the installation surface is sufficient, it is generally installed in the middle position, so that the distance between the left and right sides is equal.

For height, it refers to the height of the hook from the ground. Generally, the height of the family is used as a reference. It is advisable to be about 1.5 meters to 1.8 meters.Beautiful; if it is too high, you need to stomach or step on a small bench to hang, so it is inconvenient to use.Therefore, the installation position of the positioning hook is very important.

2. Pole

After determining the installation position, it is best to draw the hole position with a marked pen, and how many holes are needed.Then use an electric drill to punch.However, pay attention to the size of the hole, and generally refer to the size of the hole on the hook.

3. Fixed

After the holes, you can put the expansion bolt into, or the wooden pillow, and determine the corresponding bolt according to the material of the coat hook.Then align the hook to the bolt, and finally use the screw to tighten and fix it.However, when the screws are screwed, pay attention to the flatness of the hook, which must be kept horizontal with the ground, and it must not be skewed, otherwise it will affect the effect of the clothes hook and the beauty of installation.

1. Dimension measurement skills of radiator hook

Under normal circumstances, heating designers will calculate the height and width of the hedles based on the thermal demand, placement position, room orientation, decoration style and the heat dissipation of each piece of radiator.

1. If there are rooms with floor -to -ceiling windows and large bay windows, short heating slices should be installed under the window, which can effectively use space, facilitate the heat dissipation and heat circulation of the heating film, and complete the heating of the whole house.Judging from the response of good and comfortable heating users, most people now use the heating height of 1500mm and 1600mm such as the living room and bedroom, and in the bathroom, a dedicated bathroom airbuilding is used.

2. Although the radiator can be customized at will, the size of the Heating tablets can be freely selected according to the needs, how to choose the heating piece of professional heating engineers to avoid any design that affects the normal heat dissipation performance, so as not to be installed and used in the heating film.It brings danger to family property and personal safety.

2. How to install the radiator hook

1. Determine the linked drilling position in accordance with the actual position of the radiator.

2. Drill the hook position in the installation. If you install the M8 expansion bolt, use 10.5 drills to drill about 100mm deep. If it is a plastic expansion throller, use 8 drill bites and 85mm deep.

3. If you want to use the ground, you should first drill the hole with 6 drill bits on the floor, and then use a plastic expansion thrush to fix the ground to the floor, and then use the expansion thrush to fix the hook on the wall.