one,Ski double boardHow to brake

The main methods of skiing double -board brakes are the following:

1. Plide brake

After using the eight -character slope to reach a certain slope, use the head of the hillside to stand on the slope to stand on the slope.Relax on the upper body, hold the head of the snow stick in front of the hip, the snow stick hangs behind the body, the body's focus is on the inside of the front feet.Glyph.The hip weight is evenly distributed on the two snowboards. The internal rotation of the knees and ankle joints is to make the inner side of the two snowboards.The speed of slowness and eventually stop.

2. Draging method

When using the traction ropeway up the mountain, we can wear a full set of Ski equipment. Keep the two Ski panels parallel and stand in the direction of the ropeway. When the traction device arrives, the traction device is stuck on the waist or the traction device is clamped on both legs by hand.Between you can run up with the traction steel wire.The traction device is elastic, so keeping up the body upright when it is dragging on the upper drag is a must -learn skiing skills for beginners.

3. Dragging method

The drag involves a security issue, that is, how to drag and slide down the mountains from the ground.Because the beginner is not good at the slope, it is easy to slide down the drag down, which will collide with the personnel behind, and it is easy to slide down in place, causing a drag block.Pay attention to the brakes of the skiing plate underneath. First, choose some places to slow down the slope, open the tip of the board while dragging down, the snowboard forms an eight -character stand, and then moves out of the dragging.

two,Double -board SkiWhat are the main skills

1. Parallel practice

Cultivate the ability to adapt to snow and skiboards. At this time, it is best to practice in flat ground to maintain the parallel and step by step of the two Ski panels, step by step, and move to the side.

In order to find a sense of balance, it is best not to use skiing sticks at this time.It should be walking on the side of the Snow Road on the Snow Road, and walking step by step.Then, the two Ski panels slid sideways on the side of the mountain at the same time, that is, "slippery".

2. Plow glideing

The Ski board is V -shaped, that is, the two snowboards are opposite. The tail is separated, and the inner steel edge of the two Ski panels slightly stands slightly. The scientific name is "standing blade". In this posture, try to slowly decline. This is called a plow glide.In the state of plow glideing, try to increase the degree of separation of the stand -in blade and increase the double -board tail to reduce the speed of skiing, until straight, this technology becomes a plow brake.

3. Plow turning

After mastering the plow glide and plow brakes, you can try to learn the plow turning.At this time, the body weight distributed evenly on the two snowboards slowly moved to the outside of the turning arc.At the same time, the inner blade (steel edge) of the outer snowboard should be really pressed on the surface of the snow.If you want to stop turning, you only need to re -distribute your body's focus on two snowboards.

4. Plow swing swing back

Keeping the two snowboards parallel, during the taxi process, the center of gravity of the body quickly moves to the snowboard on the lower side of the mountain. This requires the legs under the mountain to have good power and control ability to avoid losing control to rush under the mountain.Then, after turning the arc from this state, the snowboard on the upper side of the mountain can be moved to a state of parallel to another snowboard. The above action process is usually the plow swing.

5. Carving

Then you can learn parallel turning and gliding. Two Ski panels are parallel, and the hips are the same as the exchanges of about the center of gravity. You can learn about the general parallel turning technology through repeated practice.On the basis of continuous practice and practice, you can perfectly control the snowboard and can Ski under the steep venue conditions.

This technology is called parallel taxi and small swinging turns. Ski competition is the development of this technology, which is also a state of disconnection along the lake.This kind of exercise is a relatively wide snowboard that is relatively wide, but it is always parallel. By controlling the body firmly, you can slip.

1. The importance of snowboard waxing

Snow plate wax is a wax that can adapt to a specific environmental temperature.When the snowboard is gliding, the bottom of the plate and snow are constantly rubbing, and the heat generated by friction will melt a small amount of snow, which formed a thin water layer between the bottom of the plate and the snow surface.If there is no wax layer protection at the bottom of the snowboard, the melted snow will penetrate into the bottom of the plate, causing damage to the snowboard.

Snow plate waxing is the most important part of the snowboard maintenance process.Waxing for the snowboard can enable you to enjoy the pleasure and random turn of skiing.At the same time, it will reduce the risk of damage to the surface and extend its life.Waxing can make the Ski board control more convenient, enhance the speed of the board on the snow, and make you turn easier.In this way, the endurance of your skiing can be more lasting.And waxing can extend the life of a snowboard and can protect the bottom of the plate.The new Ski panels are generally waxed, but after slipping once or twice, the factory wax is gone.

At the end of the snow season, the board wax must be sealed, and the boots on the fixed device are loosen to let the tight spring be in a "rest" state.The snowboard should be stored in a dry place to prevent the metal material on the edge of the snowboard to rust.Do not store the snowboard in the basement of the yin tide, or it may become a humid storage room due to rain.Snowboards that have been stored in a humid place for a long time may be deformed by the corrosion of the wood heart of the board due to inhalation of the moisture. Many slippery boards are caused by water and water corrosion.The seal wax on the bottom of the plate not only prevent the moisture from entering the plate, but also long -term storage can gradually penetrate the wax into the plate, so that the wax on the snowboard is more difficult to fall off when skiing in the coming year.

2. How to wax the Ski board

1. Before you wax the skiing board, make sure your skiing board is clean and dry, so that the board to absorb wax is convenient.

2. Slowly apply the wax on the skiing plate evenly, and adjust the electric iron to the temperature that can remove the wax without smoking.

3. Unless your skiing place is extremely cold, you can usually use any ordinary wax.It is recommended to buy an iron that is specially used for waxed, or find a hole without holes.Because unless the wax on the iron is completely cleaned, the clothes cannot be used with the same electric iron.

4. Be careful not to put the iron for too long in one place, because it may melt all the Ski panels.After applying it evenly, let the skiing board be reduced to room temperature and then continue. This process takes at least half an hour.

5. Use a hard plastic ruler to scrape the wax.Avoid using iron ruler to scrape wax, because this may hurt the Ski board, and it should be scraped along the direction of the head/tail when scraping the wax.

6. Finally, use a hard -plastic brush or a Baijie cloth to polish the bottom of the board, please continue to grind along the direction of the head/tail.

3. How to maintain maintenance skiing board

1. After returning from skiing, you must take out the snowboard from the bag, and wipe the snow on the snowboard with a soft cotton cloth or strong adsorbent paper to dry it.

2. After drying, see if there is any damage.If the plate surface is damaged, the snowboard can be placed flat. Remove the excess substances on the plate surface, ignite the prepared rubber strips and hold it horizontally, and drip the melting rubber strip on the scars of the snowboard to cool.

3. After cooling, scrape the excess rubber strip with a steel scraper. If there is a large area of damage, it should be repaired by professionals.

4. After returning from skiing, you should also repair the steel edge of the snowboard. First, use a knife with a golden steel to grind the blade and horizontal blade of the damaged blade, and then use the snowboard corner (The adjustable angle, the ideal angle is 90 degrees) along the plate to polish the steel edge. Finally, the traces left on the steel blade with the polishing process with the golden steel stones.

5. Pay attention to waxing the snowboard. At home, you can directly apply liquid or paste wax to the snowboard, or directly use the block wax on the surface of the plate.In minutes, use the plate surface to polish and polish it, so that the wax can be better attached to the plate surface.Or find a professional to wax the Ski board.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is valid. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt; error correction & gt; & gt;