1. The characteristics of anticorrosive wooden Flower stand

1. Anticorrosive wooden Flower stand is a shed Flower stand that is specially used for Hanging flowers and plants. It is made of special corrupt wood. It has a variety of characteristics such as natural, environmental protection, and moisture.Rural style.

2. The anticorrosive wood Flower rack has a strong ability to prevent the moth, which can fully dissolve the killing of fungi and viruses. The anticorrosive wood is a type of corrupted wood. It contains a lot of solubitives in itself, which can effectively prevent the bites of the worm.

3. The anticorrosive wooden Flower rack has the characteristics of moisture -proof. It will not rot if it is moisture like other wood, and the durability is particularly strong.

4. In the anticorrosive wooden Flower stand, contains a lot of discoloration factors, so it will not cause harm to the wooden appearance tissue. Under suitable conditions, part of the discoloration factor will generate many cellulose, which can form a protective layer on the outer surface to form a protective layer.For internal wood, it plays a good protective role.

2. The purpose of anticorrosive wooden Flower stand

1. The most important purpose of anticorrosive wooden Flower stand can grow beautiful flowers around the Flower stand, or some Teng Man's plants, which helps the plants grow along the Flower stand.To a better growth environment, it can also play a certain decorative role.

2. The anticorrosive wooden Flower stand is very beautiful. After exquisite design, you can not only decorate the room, but also put it in the yard. As a shaded rest, it is a natural percux, which can be used for users to rest and appreciate the scenery.

3. Anticorrosive wooden Flower stand can be used for family decoration, creating a natural decoration environment of the countryside. It can also be used in the Park, which can beautify the natural environment and create a rest place for passers -by.In the garden plant training base, it creates a natural environment for the growth of flowers and plants.

3. How to install anticorrosive wooden Flower stand

With the development of bionic technology, the bionic invention of anticorrosive wooden Flower stand has gradually been applied to life.Therefore, the anticorrosive wood designers pay attention to the imitation results, and also pay attention to the laws of natural changes.But how to install anti -corrosion wooden flower stands to be stronger?

1. Method paving method:Use stainless steel cross screws to connect to the keel on the front of the anticorrosive wooden Flower stand; fix the keel on the opposite side of the Flower stand with screws, and make a few compositions into a whole. It will not destroy the ground structure, but also freely disassemble and clean it.

2. Fixed laying method:Fix the keel on the ground with expansion screws, and the expansion filaments are made of nylon (better anti -aging).

3. Suspension laying method:The keel can be connected to a frame or a well -character frame structure on the ground, and then laid the Flower stand.

The specific measures are as follows:

1. Treatment of the grassroots level of the wooden structure: During the design and construction, the air circulation between the anticorrosive wood and the ground should be fully maintained.

2. When making and installing anticorrosive wooden flower frames, 0.2-1cm gap between anticorrosive wood should be left (then determine the gap size according to the moisture content of the wood, and the water content of the wood should not exceed 0.8cm.The expansion of water and anticorrosive wood.

3. Fang columns with a thickness of more than 50mm or more than 90mm are opened in the center of the back of the back.

4. Hardware to avoid rust corrosion in the future and apply stainless steel, hot -dip galvanized or copper materials.Please drill in advance when connecting installation to avoid anti -corrosion wood cracking.

5. Use the existing size and shape as much as possible. The damaged part should be painted with preservatives and Outdoor protective coatings. Because the anticorrosive wood itself is a semi -finished product, the rough part can be reduced to less than 20%after the laid.Light again, if you want to have a better effect, you can paint Outdoor protection coatings after cleaning the surface.In the case of a rainy day, it is best to cover it with plastic cloth first, and then brush out the Outdoor protection coatings after the sun is clear. It should be avoided within 24 hours after painting.

6. Surface user external protective coatings or oil -based coatings are applied (only once). In order to achieve the best results, avoid people walking or heavy objects within 48 hours, so as not to destroy the protective film that has been formed by the anticorrosive wood layer.EssenceIf you want to obtain a better anti -dirty effect, you can do two special Outdoor varnish treatment if necessary.

1. How much is one Square meter in the sun?

The price of the sunrier canopy is available from dozens to hundreds.The price of sunlight plates with different materials is much different. Generally, the price of sunrochemine of the material is 1561 Square meters. Of course, the difference in the material of the material will also be different.The price of PC Sunshine board is not a constant price, but a comprehensive consideration of the technical process level and the performance of the board. At that time, the price and other costs of raw materials and other costs were calculated.

The price of the PC Sunshine board is calculated as follows: 6mm-16mm thickness, and the general price is from 25 yuan to 100 yuan/. The thickness of the thickness of this interval is relatively common.X -shaped, rice type, honeycomb type.The thickness is 16mm-40mm, and the price is generally 80 yuan-2060 yuan/. The PC sunboard with this interval thickness is generally less used, and it is also divided into various shapes.

2. How to install the Sunshine Fragrance

1. First check the skeleton, which must be flat without welding scars and burrs.The skeleton must be completely dry and there must be no volatile solvents.

2. Powder the tan -based waterproof tape on both sides of the skeleton to form a small sink.

3. Place the sunboard on the skeleton, and the telescopic joints are reserved between the board and the plate.

4. Press the EPDM press on the interface between the board and the plate.

5. Fix it with a drilling screw.

6. The skeleton must be used at 1.05m in the middle of the sunboard.

7. The sunlight board on the wall shall not be directly contacted with the wall surface, fix it on the wall with angle aluminum, and then put the sunboard in and install it.

8. The sunblasts are sealing the mouth with aluminum tape first, and then fixing the edge or corner aluminum.

Three, installationSunshine Steakprecautions

1. Check the cutting size of the board and whether the reservation of the bulletin is appropriate. We must pay special attention to leaving enough uniformly swelling gaps. The calculation formula is as follows: Total expansion gap = bulging coefficient*The maximum temperature before and after local installation of local installation*board length.

2. The section of the plate was clamped in the large -scale plate installation engineering must contain at least one tendon rib, or the smallest part of the section of the edge of the board is 20mm.

3. Recognize the surface of the surface of the board, and install the surface out of the outside, and never allow the ultraviolet side to be installed inward.

4. Before installing, the protective film surrounded by the plate is 30mm-50mm. Do not clamp the protective film of the profile, but you should not remove too much, so as not to damage the board due to operation.

5. When the self -attacking nail is tightened, the force should be evenly tightened to ensure that the type plate is truly crushed and densely sealed.

6. In the case of cold bending of hollow plates, its curved radius must not be 175 times the thickness of the analytical material.

7. The hollow plate can only bend the ribs in the direction of the ribs.

8. The tilt installation of hollow plates should be directed to the ribs, which is conducive to the export of condensation water.

1. Sunshine roomPC endurance boardHow are you?

1. Advantages of PC endurance board Sunshine room

(1) High light transmission, like glass, is as high as 89%, ensuring that the sun room is combined with nature and sunlight.

(2) Strong compressive resistance. The impact is dozens to hundreds of times of ordinary glass. It has high hardness and is safer than glass material.

(3) The material is lightweight. The material belongs to the plastic material. The material is very light. It can change the shape at will to solve the problem of self -in -law.

(4) Temperature -resistant heat insulation, the surface of the PC endurance board has a UV coating, which can effectively block ultraviolet rays, and for a long time, it is not easy to turn yellow.

2. PC endurance board Sunshine room disadvantages

The PC endurance board is light and requires a certain glass or other auxiliary materials to be thickened to make the plate stronger.In terms of expenses, it is higher than glass.Pay attention to the flat mouth cutting during the cutting period to avoid scratches during installation.

The PC endurance board is a new type of Sunshine room material. The surface UV coating can certainly resist ultraviolet rays and play a role in heat insulation. The materials are not easy to age and turn yellow.It is not prone to rupture and explosion in C. Although the price is more expensive than glass, the PC endurance board does not explode, no rupture, and yellowing.SunshineThe best choice material.

Second, the common problems of the PC endurance board of the sun room

1. Is the PC endurance board an acrylic board?Is it organic glass?

No, PC endurance board is also called polycarbonate board, which is an emerging material in recent years. It is processed by high -performance engineering plastic polycarbonate.The acrylic board is a type of organic glass. The weather resistance, light transmission rate and impact -resistant Biac clan board of PC endurance boards are more advantageous.

2. After a long time, will the PC endurance board be yellow?

The PC endurance board has a UV coating. Under the direct sunlight, the PC endurance board can absorb 99%of ultraviolet rays. It is not easy to aging and yellow. The light transmission rate in 10 years is only about 6%.

3. Will the PC board release a toxic smell?

PC endurance board raw materials are polycarbonate. There is no need to add any substances. UV coating is non -toxic and pollution, and burning will not produce toxic gases.The acrylic board is an organic material, and a small amount of toxic gases will be generated when burning.

4. Deformation as soon as the sun is exposed?Can you crack when you encounter low temperature below 0 degrees?

No, the PC endurance board has the function of high temperature resistance and low temperature resistance, and the performance is stable between 40 degrees and negative 120 degrees.

5. How about PC endurance board?

The PC endurance board has good impact resistance, which is 300 times that of the same thickness of ordinary glass, 30 times that of organic glass, and 20 times that of tempered glass.It can resist hail, snow pressure, and even high -altitude parabolic damage, effectively protecting property and personnel safety.

6. Will it not become a large steamer in the summer?

The K value of the PC endurance board with the same thickness is 7%-25%higher than that of glass, and the heat insulation effect is 7%-25%higher than similar glass.curtain.

7. PC endurance board is not as good as glass?

The PC endurance board's light transmission is similar to the glass, but the impact resistance is 2-20 times that of tempered glass. The heat insulation and sound insulation performance is better than the same thickness glass.

8. How many years are PC endurance board life?

Under normal circumstances, the life expectancy of PC endurance board is 15 to 20 years. If it is properly maintained, the service life will be longer.

9. What is the price of PC endurance board for sun room?

The price of the mobile sun room is calculated according to the development area. The specific price is based on the size and material of the built. The general price of the German imported PC endurance board material is generally 2,500 yuan to 3,000 yuan/Square meter.

10. Will it be noisy on rainy days?

The sound insulation effect of the PC endurance board is better than the same thickness of the same thickness, and the sound will be less sound insulating than the same thickness, so the sound dripping on the sun room will be smaller.

11. Is PC endurance board Sunshine room illegal building?

No matter what materials are used, consult the relevant departments and properties in front of the Sunshine room, and go through the corresponding approval procedures to avoid illegal construction.