1. Why is the fishing line broken

When fishing, the most depressed thing was that it was easy to catch a fish, but the fish line was broken when the pole was lifted.Many people will complain at this time that the quality of the fish line is not good. In fact, there are many reasons for the fish line break, including:

1. Old residual secondary lines lead to disconnection

(1) Old line:First of all, it is manifested in the judgment of whether the old line can be used. Some fishermen took a long time, caught a lot of fish, regarded it as a contributor, and could not change it.Change the line.In fact, even if it is a good fishing line, after a long time of sunlight, the ultraviolet destruction effect is very strong, which will make the fishing line rigid and gray and brittle, and the tension is greatly reduced.Furthermore, the fishing line has been dragged many times, which may be deformed, or flat or thin.Sometimes due to being squeezed or compressed, or a dead bend, it becomes a hidden danger.Therefore, it is necessary to check it frequently when using the fish wire. Those with "pathological" should be replaced. The fishing line is a consumables that should be changed frequently.

(2) Line:The inferior line is charged and mixed in the high -quality fishing line. These wires have a small tensile force and a large extension.There are also some Fishing lines. The original quality is good. Later, because the storage time is too long and deteriorates, from superiority to inferiority.Using this fish wire may also be easily disconnected.

2. Improper nodules cause disconnection

The nodules on the fishing line are also the main reason for disconnection.During the knot, the two lines are twisted with each other to produce the cutting effect. The knot is too tight to easily flatten the fishing line, and the flat line is easy to break.

The nodules on the main line of the hand pole are at both ends, and the upper end is connected to the fishing rod. Most of them are lively. The tip of the pole tip is connected to the line. Because it is a double -stranded Sleeve, the line is not easy to break.It is best to connect to the fishing line and the fishing group. It is best not to use the word "".

The most concentrated part of the broken line is the sub -line. Usually it is smaller, shorter and thinner than the main line, and there are nodules at both ends.The most common broken lines are tightly tightened because the hook is tight. Press the sub -wire to flatten, and the sub -wire will be pulled off from the hook handle after the fish hook is stunned.If the sub -line is led from behind the hook, it is most likely to be cut off by the gear head on the hook handle.

3. Improper operation causes disconnection

Because the big fish is really rare to pull the fishing line directly, because the fishing rod is supported by the fishing line as a strong support. After the fish is put on the fish, the tension is passed from the fishing line to the pole.Function, at this time, the fishing rod will play a soft and hard elasticity. It is thicker one by one, one section one by one, from the tip of the pole to the handle.The stronger its tensile resistance, the fish is not moving, and it stands straight. It is this "soft power" that relieves the death of the big fish, and it also protects the fishing line from being damaged.

Of course, the tension of the pole also has a limit, and a certain force pole will be broken.Due to the hard power of the pole, when the fish is not moved, its strength is concentrated on the fishing line, causing a disconnection.So many fishermen know that the hard pole is easy to break.Not good at using the elasticity of the fishing rod, such as the fish or hook Hanging the bottom, pulling the line with your hands, no elasticity in your hands, hard touch, and the fishing line is likely to be pulled off.This method of dragging the lines is a strategy to preserve the safety of the pole line when the hook hangs.

There is also a break -up moment that is most likely to happen and often ignores. It is that after the big fish was copied and copied ashore, it folded and fought on the shore.Drag, the sub -line will break.Therefore, the fish in the copy of the net must be solid, not to make it toss, neither hurts the hands nor break the line.

Second, how to pick up the fishing line is the most strong

In the daily fishing process, everyone often encounters unexpectedly disconnecting situations. In the case of disconnection, the disconnection on the hand can be used to use it. The specific method step is:

1. Flat the lines of the two fish lines, and try to flatten the lines as much as possible. Do not have different lengths.

2. Put the two side -by -side fish wires around the fingers (can also be two laps), and then twist an eight -character buckle.

3. Put the two side -by -side heads from the outer eight -character hole.

4. Pull the two line heads in the right hand, pull the two lines on the other side of the left hand, and pull it hard.

5. Use scissors to remove the excess line head. After cutting, you can use a lighter to bake the line head slightly to make the head head flatter and the wiring is completed.

Third, can the fishing line be broken after being broken?

Many fishermen think that it is not strong to connect the fish wire. This kind of worry is original. After all, a knot has been knotted on the fish line.Compared with fishing, it can be connected to the line and re -use it. It is much stronger than Linyuan's envy fish. Moreover, we are generally connected to the main line. Generally, the main line is one to two larger than the sub -line.It is okay to deal with normal fishing feelings.

When using the connected break, pay attention to the following points:

1. Do not be too fierce.After all, we are not using a complete line, and the excessive rod will cause the fish wire to be disconnected from the knot.

2. It is not recommended to use a hard tone fishing rod.After all, the receiving line is "injured". Using the ultra -hard fishing rod will accidentally increase the force at the knot (unless your method is super well -skilled), it is recommended that you use 28 tunes or softer poles.The advantage of using this fishing rod is that you can make full use of the rod to protect the fish wire slightly.

3. Do not use it for a long time.It is a way to connect the fish wire with it. During the secure period, as long as the conditions are mature, it is better to replace it with a fish wire without joints.

1. Several types of fish wires are divided into

The fish line is one of the important components of fishing tackles. Whether the fishing line is properly related to the fishing effect directly. For example, the choice of the type of fish wire is to pay attention. There are many types of fish lines. According to different classification methods, different types can be divided into different types:

1. According to the material

(1) nylon line:nylon wire is also called traditional lines or four -color lines. Generally, resin materials are made of resin materials. It is made of machining filaments. This fish wire has no color transparent, strong tensile, good elasticity, fast water cutting, and high fishing sensitivity.Durable, durable, soft, not easy to be crispy in winter, and verticality, so the nylon line occupies a dominant position in the market.

(2) Carbon cable:Carbon lines mainly refer to a fish wire made of carbon materials during the manufacturing process. This carbon -based fish wire is more abrasion -resistant, but the ductility is poor.The proportion of the carbon line is greater than the proportion of water, so its water cutting is better, which is more suitable for use in the rock fishing.Because the texture of the carbon line is relatively hard, it is often used for the eldest son line or tie of the Ship fishing.

(3) Weaving:It is a fish wire woven from multiple silk threads. The early weaving lines did not add a membrane, it was easy to absorb water, and it was not easy to maintain. However, because of its abrasion resistance and tensionHousekeeping, but the water cutting is poor.There is also a waterproof woven wire that adds a membrane technology during the manufacturing process, which is made of multi -stranded weaving lines, also known as fire lines.This weaving wiring is also good, but its damaged part is easy to form a hair ball, which is easy to break and the texture is harder.The fusion line is a weaving line that adds a multi -bhomistarian nylon line to the weaving line, and in this process.Its advantages are high tensile values and abrasion resistance.Because the nylon wire is added to the production, this thread is softer than the normal wiring and good back.

(4) Ceramic line:The ceramic line is made of high -molecular aggregate materials. In the formation of the online body, it is made of special resin to fill the spare special resin to improve the tensile strength and waterproofness of the fish wire.Then add the second layer of special resin to enhance the wear resistance of the fishing line.Finally, add special resin to the third layer to improve water resistance.The fish wire of the ceramic line has excellent tensile strength and abrasion resistance. It is not easy to nodule, light quality, and the feedback of fish feelings is more sensitive.

(5) Ultra -strong PE fiber fishing line:Taking the super PE fiber as the raw material, the surface of the thread is added with a lubricant to improve the layer on the surface of the fish wire.This material of the fish line is durable, long -lasting, and can prevent wear and fading, reduce tangels, and knots are more convenient. It has the characteristics of resistance, no cutting wires, durable performance, and fine line diameter. It is suitable for fishing as fishing.Line, kite line, water sliding traction line.

(6) Synthetic fish line:The synthetic fish wire is the process of adding other materials to the finished product during the production of the nylon line, so that the line can float on the fishing line that floats on the water or suspended in the water.Suitable for the semi -floating water line as the rock fishing, the full floating line containing the parade material, and the resin processing lines to add tensile substances.

2. Press the source of the fish line

It can be divided into three types: domestic, imported and joint ventures.The raw materials produced by joint ventures come from imports and are processed and produced by domestic. Many people like to use the lines produced by China -foreign joint ventures, because their prices are cheaper than imported, and the pulling force and technology are also applicable.

3.

It can be divided into powerful lines, super -powerful lines, and strong strength lines.

4. Press the color score

There are many types of white, light blue, dark blue, yellow, light red, color lines and other types.

5. Divide in fishing

It can be divided into competitive lines and leisure lines. The competitive line is a fish line designed for competitive. The leisure line is a non -professional line designed for the low requirements of the line.fishing people.

Second, which type of fishing line is easier to use

There are many types of Fishing lines. Different types of fish lines are suitable for different fish feelings. Generally, it is not easy to say which fish line is best. When choosing, it is mainly based on the fishing environment and the types of fishing.EssenceA good fish line generally requires the following four requirements:

1. Good liquidity

The so -called liquidity is that the thread remains less in water after water.

2. Strong tension

That is, strong, durable, and not easy to break.The Fishing lines sold by Fishing gear stores will indicate the tension of the fish line on the outer packaging, which can be purchased according to the needs.

3. Do not bend and deform

No matter how entangled the fish line, it is vertical after letting go.The curved thread is easy to make the hook in the water tilt, the fish is not easy to hook, and it is easy to decide.

4. soft

Whether it is a thick line or a thin line, it should be soft, and it should not be hard after a period of time, indicating that it is a good line.

1. How to tie the fish line on the fishing rod

It is very important to tie the fish wire and fishing rod correctly in the fishing activity.If the binding method is incorrect, it may cause the fish wire to be broken in the fishing process.

1. Prepare the fish line

Choose the right fish wire, then gently wipe the fish line with a clean wet cloth to remove the dust and dirt on the surface, and apply an appropriate amount of lubricant on the fish line to reduce friction and improve fishing efficiency.The end of the fish wire is trimmed neatly, avoiding the frizzy line heads affecting the effect of the line.

2. Check out

Check whether the surface of the fishing rod is damaged, cracks or deformation, etc.; check whether the fishing rod interface is firm to avoid falling off or broken during the fishing process; check whether the weight and length of the fishing rod meet the requirements to ensure that it can meet during the use process to meet the use of the process.The best effect.

3. The steps of tie the fishing line and fishing rod

(1) Preparation tools: need to prepare scissors, cutting knives, tiered boards and other tools.

(2) Fixed fish wire: Fix the organized fish wire on the tie line, and then place the tie line on the flat countertop.

(3) Winding: Use your right thumb and index finger to pinch the head on the tie on the line, and go around inward to ensure that the coils that are around are flat and close.

(4) Adjust the length of the ring: Gently pull the center of the coil with the right thumb and index to the center of the coil to gradually reduce the coil and adjust the length of the ring to achieve the appropriate length.Generally speaking, the length of the circle should be slightly shorter from the pole handle.

(5) Fixed coil: Place the center position of the coil on the pole handle, use the right thumb and index finger to pinch the coil and the pole handle, and gently pull the wire head at both ends, tighten the coil and fix it on the pole handle.EssenceMake sure the coil is fixed and stable to avoid loosening or falling off during use.

(6) Adjust the density of the coil: Use the right thumb and the index to light the center position of the inside to make the part of the coil and the pole handle contact more dense.This can make the entire coil fixed on the pole handle more firmly.

(7) Fixed line on the line: Fix the upper end on the fishing hook to ensure that it is fixed and stable, so that it will not fall off or slide during the fishing process.

(8) Complete the tie line: Check whether the tied fish wire is firm, neat, and noble.If you are satisfied, trim the extra line head to complete the line tie process.

(9) Check the fishing status: After completing the line tie, hang the fishing hook in the water for testing.Check whether the fishing status is normal to ensure that there is no looseness at the connection between the fish line and the fishing rod.If everything is normal, you can carry out fishing activities with peace of mind.

Second, what are the tied methods of the fish line connection

The fishing line is the fishing line. For a newbie of fishing, it is important to learn to tie line. When we buy a pole, what we need to do is to connect the pole and the line. However, it is not a simple matter.Many novice friends are easy to tie or break the lines, affecting fishing.The tie method of the fishing line is divided into two types of Fishing rods and Fish hooks:

(1) How to tie fish rods in fish lines

1. The valve core connection method

(1) Put a soft head on the tip of the pole and fold it into a semi -round curved.

(2) Take a section of valve core and hold the soft band.

(3) Put in the fish line from the soft Belt ring, and then hit a knot.

When taking the wire, the valve core retreats from the soft Belt, and the knot is successful.

2. Live -set ring connection method

(1) Put a pimple at the top of the soft Belt.

(2) Put the fish line on the top of the ring.

(3) Fold the ring into a double ring.

(4) overlap the double ring together.

(5) Pass the soft band from the ring.

(6) Tighten the line to make the ring tightly hold the soft band.

Just loosen the ring when taking the wire and exit the soft band from the ring.

3. Space bean connection method

(1) Fold the top of the fish line into a semicircular ring.

(2) Pass space Beans from the semi -ring.

(3) Put a soft band on the tip of the pole.

(4) Put the semi -circular coil and hold the soft band.

(5) Tighten the fish line, narrow the coil, and tighten the soft band.

Expand the coils when taking the wire and draw a soft band.

4. Connection ring connection method

(1) First bend the soft band above the tip of the pole into a ring, and tighten the interface with a thread.

(2) Then connect the ring with the ring on the soft band together.

When taking the wire, just take off the connection ring, you can remove the fishing line from the fishing rod.

(2) What are the ways to tie Fish hooks in the fish wire

The fishing line tie fish hook should also be the fishermen. At the same time, it can be tied and tied to the fishing cost. After all, the Fishing gear shop does business, the hook line consumes time, and it is impossible for others to serve us in vain.There are many ways to tie the fish hook, mainly:

1. Wrap the fish wire to about two laps on the hook handle, and then tighten it.

2. First wrap the fish wire around the hook four or five laps, and then tighten the previously reserved fish line through the coil.

3. Wrap the fish wire from the middle position of the fish hook to the handle, then tighten and reserve a coil. Finally, pull one end of the fish line to pull tightly.

4. Start the fish wire from the bottom of the hook handle, and then wrap it to a certain number of laps and leave a part of the thread head.The opposite direction of the hook tip is easier to get fish, so try to keep the tip outward as much as possible after the hook is tied.

5. Wrap the fish line on the handle, then leave a part of the coil and tighten it.

6. First take a fish hook with a suitable fishing line first, wrap it around the handle for five or six laps. When the fish line is slipped outward, it is blocked with your fingers, and then slowly pulls the head when tightening.The other fish hook also uses the same binding method. After the hook distance is fixed, the double hook is removed and the double -share line is knotted. Finally, the small circle is tightened.

Kind tips:If you first learn fishing, it does nt matter if you do nt bind the hooks. You can also buy the finished sub -line to use it. After learning to tie the hooks, you can buy the fish line and the hook for the hook.

1. What is the effect of the thickness of the fish line on fishing

The fish wire has a very important position among all fishing tools. The quality and coarse lines of the fish line will have a great impact on fishing.

Generally speaking, the thinner the fish line, the better the fish mouth, but when using the fine fish wire, you need to use a softer fishing rod to protect the fish wire, otherwise you will run the fish at a break.The mouth will be worse, but it can play a role in preventing small fish from making nests, preventing decourse Running fish, and preventing lines from cutting fish.

Second, the fish line is thick or fine

The rough fish line and fine fish line have their own benefits. Generally speaking, choose the right thickfish fish wire according to the actual fishing scene:

1. Use the scene of the fine fish line

(1) When fishing small fish, such as fishing small fish, white ravioli, liu root fish and other small fish, you need to use a fine fish wire.

(2) During the fishing in late autumn, winter and early spring, due to the low water temperature and poor activity of the fish, the opening range is small. Only using a fine fish line can the fish be eaten into the mouth.

(3) When the sliding fish and the fish are returned, the fish is very vigilant and the vitality is relatively poor after the fish is caught. When using the fine fish line, the fish mouth will be much better.

(4) When there are very few fish in the nest, there are only one or two fish, and eating bait will be very cautious. Even using the body to shoot Fishing lines and repeatedly test it.Sex, let the fish dare to bite the hook.

2. Use the scene of the rough fish line

(1) When fishing, you must use a rough fish line to prevent Running the fish from the broken line. It is difficult to catch a large fish, because the fish wire is too thin to run the fish, the loss is too large.

(2) During the black pit fishing, there are a lot of fish in the fishing spots, and the fish mouth is very good. The use of the rough fish line can quickly return the fish to increase the speed of fish grabbing and maximize the fishing.

(3) During the wild fishing, when the fish feels unknown, use coarse lines. In case of big fish, you can avoid Running fish.

In fact, for veterans of fishing, two types of fishing groups are usually prepared. The first plan is hard pole, thick lines, large hooks, and large drifts.When there are a lot of fish in the nest, and the fish is full of vitality, when the fish mouth is very good, the plan will be used to grab the fish; when the fish in the nest is less, the fish's vitality is poor, the fish mouth is weakAt that time, the scheme will be used to make the fish.Especially when fishing in black pit, this fishing method is almost a must -have for fishing masters.

1. The correct installation method of Fish drift

In fishing activities, the proper installation of Fish drift is important for fishing. Fish drifting is the eyes of the fishermen. It can reflect the situation of the fish bite and help us grasp the underwater situation. So how to install the Fish drift?

1. Choose the right Fish drift

Choose the right Fish drift according to factors such as fishing environment, deep water, and water flow.

2. Install Fish drifting seat

Put the Fish drifting on the fish line to ensure that the Fish drifting seat is close to the fish line.If necessary, you can use a silicone Tube or other materials to increase the sealing effect.

3. Install Fish drift

Insert the fish into the Fish drift to ensure that the Fish drift and the fish line are vertical, and then adjust the position of the Fish drift to achieve a suitable depth.Generally speaking, the tip of the Fish drifting should be about 1-2 cm below the water surface, so as to ensure that a small angle can be formed below the water surface, thereby more sensitively reflecting the situation of the fish bite hook.

4. Fixed Fish drift

Use space Beans or rubber rings to fix the fish on the fish line to ensure that the Fish drift will not slide or fall off.Space Beans and rubber rings can be purchased in fishing gear shops or made by themselves.

5. Adjust buoyancy

Adjust the buoyancy of Fish drift as needed.If you need to increase the buoyancy, you can add foam or other lightweight materials to the Fish drift; if you need to reduce the buoyancy, the amount of foam or other lightweight materials can be reduced.

6. Test

After installing the Fish drift, test to ensure that it work normally.Hang the hook in the water and observe the reaction of the Fish drift.If the hook is not hung on any item, the Fish drift should be kept below the water surface; if the hook is hung on the items, the Fish drift should rise quickly or move to different positions.

2. How to tie different types of buoy to the fish line

The buoy is also called float and Fish drift. It is one of the indispensable tools when fishing. It is also one of the important indicators to measure fishing technology and experience. Generally, Fish drift is tied to the fish line. According to the different forms of Fish drift, the installation form also forms the form of installation.Not the same:

1. The method of vertical floats to the fish line

The vertical float is also called a Taiwanese fishing float, which refers to a fishing Tool that conveys the information of the fish swallowing the bait and the location of the place where the bait is.From a structure, floats are divided into three parts: drifting, drift body and drift tail.If the material is divided, it is mainly Balshan floating, reed floats, feathers floats and nano -floating.

The steps of vertical floats to the fish line:

(1) Put into two space Beans on the main line.

(2) Then put into a drifting seat. Be careful to match the size of the floating drifting feet. Do not be too large or too small.

(3) After entering the drifting seat, two space Beans are installed to lock the drifting seat.

(4) Then put into the lead leather seat and tie the eight -character ring.

(5) Insert the float foot into the drifting seat and complete the connection between the float and the main line.

2. The method of spherical floats to the fish line

The spherical float, also known as the sea pole ball drift, is generally ABS material. From the structure of the structure, the float is mainly divided into drift tails, belly and drift tip. There is a round hole in the drift tip.of.

Steps of spherical floats to the fish line:

(1) Different from the hand pole, the spherical floats generally do not need to drift the seat, but use the connector to connect the main line to the float.

(2) Similar to the installation steps of the stand -up floating drift, two space Beans are fixed on the main line on the main line.

(3) Put on the other end of the connector into the reserved hole of the drifting tip and lock it to complete the installation of spherical float.

2. The method of seven -star drift on the fish line

Qixing Drifting is mainly used for traditional fishing. Qixing Drifting refers to seven different colorful Beans with different colors. Each eye -catching bean can be worn on the fish line like space Beans to pass the role of eating hook signals.Its color is generally three types of red, yellow, and red and yellow. In addition, there is also a fluorescent seven -star drift loved by night fishing enthusiasts.

The steps of seven stars drift on the fish line:

(1) Take a pack of seven stars.

(2) Put the Qixing sequentially on the main line according to the method of installing space Beans.

(3) Then use two space Beans to fix the last leading leather seat, and install an appropriate amount of lead Skin weight on the lead leather seat. If you use a dumplings with heavy weight, you can ignore this step.

(4) The fish hook can be used for fishing, and the seven -star drift installation is completed.

4. The method of the horizontal float on the fish line

The horizontal float is also called automatic bottom -free dot drift. It consists of three parts: Zhongtong wire ring, drift body and drifting bodies.The point wave line is mainly composed of drift -assisted lead pendants, buffer beads, dot drift, main lead pendant, and link buckle.Generally speaking, the main lead pendant is more important than auxiliary lead pendants, and because the buffer beads and lead pendants can be slid at random, so you do nt need to adjust the bait into the water to find it automatically.When the fish bite hook, the auxiliary lead is driven, the water line is pulled, so that the floats are swinging up and down, forming a wave effect, so it is named a little wave floating.

The steps of the horizontal float on the fish line:

(1) Pass the main line through the auxiliary lead and buffer bead.

(2) Pass the main line through the wave float.

(3) Then pass the main line through the buffer bead and the main lead.

(4) Tie the main line on the connection buckle or the eight -character ring.

(5) Tie the sub -line group on the connection or eight -character ring, and hang the bait to fish.