1. How to make creativity link

1. Link the bottle cap

Use the two vertical lines on the two sides of the bottle cap as the two sides, and keep the two vertical lines at about 1cm as much as possible. Then, use a knife to cut the bottle cap along the vertical line to remove the two pieces.After this step is done, two grooves will be formed on the bottle cap, and it is precisely these two grooves that can be used for Hanging things.Finally, the bottle cap is pasted and fixed on the wall. At this point, a simple hook is done.

Or I think it is only monotonous with a bottle cap, which is too simple, and you can also choose to add a few back -shaped needles.In this way, you do nt need to cut two pieces on the bottle cap to form two pieces to form things Hanging. Instead, the back -shaped needle is poured into a wire, and the tail is bent into a small hook.Put the back -shaped needle in, and then fix the bottle cap to the wall, and the hook is completed!

Although this hook is easy to do and the cost is very low, there is also a small defect, that is, it is only suitable for putting some small things, or some light debris, otherwise it will be easy.

2. hook branches

When you go to the Park to take a walk, you can pick up some small branches with a lot of branches, and then trim them into similar sizes, and then brush it on your favorite color.The screws nail them in a row.

It is firm and very high -level. No matter where you hang it, there is a natural charm, which immediately enhances the style of the home.And the hooks made of this are relatively strong, it will not fall easily, and there are more things that can be hung.

two,Wall linked DIY handmade tutorial

tools/raw materials:Small brush, a cup of water, paper towels, palette, tape, nails, hammer or screwdriver,Three colors of pigments, wooden knobs, and threading.

Method/Step:

1,Open the pigment box, freely match different colors, mix or alternately use.At the beginning, it is recommended that you start with a simple color.

2. Use a pencil to mark the part that is about to colored, and the tape sharing area.

3. Dig a little pigment with a small brush at the end of the brush and put it in the palette, and change the color by mixing with water or mixing with other colors.After digging out a piece of paint, clean the small brush, continue to dig the second color, and mix them.

4. When you make up your satisfactory color, you can start coloring. Mix the paint with a brush head with a pen and dip it out.

5. color according to the area marked.

6. Put the colorful knob on one side and clean the pen in the water.

7. After the pigment is dry, remove the tape.

8. Tort the threaded screw (actually matched with the knob) to the behind the knob until it is completely fixed.

9. Use a hammer and moderate nails on the wall to cut a small hole, or directly use an electric screw knife to hit a hole.

10. Fix the hooks that are done on the wall, and you can hang your favorite jewelry or clothing.

11. After the operation is skilled, you can make various colors and styles of wall linked, gradient, Pop, stripes, geometric patterns to choose from.

The Buddha beads are plants under the family of Chrysanthemum, which are native to South Africa.The beads are fleshy, spherical to spindle -shaped, and there is a transparent longitudinal pattern in the center of the leaf, and there is a slightly pointed protrusion at the end of the tail.The stems are Hanging or the soil surface grows, so it is mostly cultivated as a suspension plant.

Buddha beads belong to succulent, native to South Africa.The leaf meat, the spherical to the spindle shape, the leaf center has a transparent longitudinal pattern, and there is a slightly pointed protrusions at the end of the tail.The stems are Hanging or the soil surface grows, so it is mostly cultivated as a suspension plant.Seeing that the fleshy meat like beads never thought about it and would bloom.

Cultivation technology

1. Soil: The root system of the plant is very shallow, which can be placed shallowly. Generally, the bottom hole is used with tiles, and a layer of cornography or coarse sand are paved to increase the breathability and water filtration (especially the plastic potted plants that are currently commonly used).The soil is best to use rotten leaf soil (the fallen leaves of autumn and winter trees are mixed with a certain amount of soil or a certain sand. The soil and the sand are about 1: 3).

2. Light: Buddha beads like a semi -yin environment, the light is too weak and grows slowly, and the color is dim.If the light is too strong, it will cause the pearl body due to exposure, causing the dried orchid to scorch.The growth temperature is around 12 to eighteen degrees, and it is not less than five degrees in winter.

3. Temperature: Sexuality is warm and humid, which is cold -resistant (it can withstand low temperatures of 0 C when cultivated in the Jianghuai area), high temperature resistance, the optimal temperature is about 20 C to 28 C.It grows slowly at high temperature and low temperature, especially in the high temperature environment above 30 C. It is almost dormant, and less watering should be watered, otherwise it is easy to rot.This is also one of the keys to cultivation.

4. Watering: Due to the leaf meat, juicy, drought resistance, watering should be dry and not wet during cultivation. This is one of the key to success.When the weather is dry, you can spray the leaves and vines to make up for the lack of moisture, and keep the beads full of green.Compared to half yin, the exposure may burn the bead body, and the light is too weak and does not grow strong.

5. Fertilization: The strong growth of spring and autumn should be applied thinly, and it is often sprayed with 1-3 % of nitrogen fertilizer and potassium dihydrogen phosphate on the leaf surface.

6. Pruning: During the repair, not just cut off the excess part, but start the trimming from the edge of the Flower pot or the edge of the Flower pot.It is the "top" that everyone usually says.There will be separate branches on the cut place, the more branches of the top, the more branches, and the more branches will naturally explode.

7. Preventive diseases and insect pests: Few pests and insect pests.The aphids in spring are one of them. Wiped it in time or spray 1500 times oxidative music to kill; mites in summer and autumn are second, and 1000 times trichlosterol may be killed.Pay attention to ventilation and increase the humidity of the leaf surface to reduce infection mites.

8. Breeding: The succulent beads can be cut and breed, and the branches are very easy to take root. You can cut a few sections in spring and autumn. Half are buried into the sand or loose soil, keeping moist but not accumulating water, and you will quickly take root for planting.

precautions for the breeding of polyphonic beads

1. From March to December each year is the growth period of the plant. There is a short half dormant in summer. If the light is less likely to grow long, the stems will become fragile, and the spacing between the leaves will be opened for a long time.In plants that grow in full sunshine, the plant types are stubborn strong, the leaves are full, and the spacing of the leaves will be relatively close.

2. Keep the soil slightly wet to avoid stagnant water during the growth period.The soil can be mixed with cornography and a small amount of perlite, with a ratio of about 6: 3: 1.

3. Keep as much as possible in winter as much as possible, otherwise the temperature is too low to be frostbite and die, which is less resistant to frost.When the summer temperature exceeds 35 C, the entire plant will grow slowly.At this time, watering should be reduced to prevent rotten rot from the root of the pot soil.And strengthen ventilation, appropriate shades, avoid the sun exposure.

4. Avoid long -term rain during cultivation, otherwise the stems will be rotten.

5. The Buddha beads are still relatively fast. It is almost the same for changing the pot in 1 to 2 years. The pot is changed before watering in the first spring.The Chairman of the Buddha has a lot of branches.Breeding can cut the long section directly. The cuttings are very simple. Take a section of the healthy Buddha bead and cut the dry wound cuttings in a slightly humid sand soil. You can also put it directly on the soil surface.

[House rack in the bathroom] Which material of the bathroom shelf is good for the bathroom shelf, how to buy the shelf in the bathroom?

The shower room setting rack is generally combined with a bottom plate and a pillar to form a shelf, which is mostly supported by the strip bracket. The bottom plate is supported. The shape is unique, the design is smart, the loading and unloading is simple, clean and beautiful, and open design.storage at a glance.

Which material is good in the bathroom?

1. glass bathroom stand rack

Features: General glass racks are made of tempered glass.Not only is styling and simple, but also easy to clean, but to avoid strong impact on the glass surface.

Cost: high

2. Plastic bathroom shelf

Features: The plastic bathroom rack has the characteristics of corrosion resistance, anti -aging, rustless, non -toxic, odorless, high pressure resistance, light weight, simple construction, etc.

Cost -effective: low

3. Stainless steel bathroom shelf

Features: The stainless steel bathroom rack has the case that does not cause corrosion, erosion, rust, or wear.Because stainless steel has good wear resistance.Therefore, it can keep the integrity of the structural component engineering design and lasting time.

Cost -effective: medium

4. Alloy bathroom standing rack

Features: The alloy bathroom rack is a metal with metal characteristics composed of two or more metals or non -metals. It can be decorated in a bathroom of various colors and has a better decorative effect.

Cost -effective: medium and high

How to buy a shelf in the bathroom?

1. When installing the rack, be sure to consider the entire layout and the needs of our daily life to install. In the bathroom, the shelf is mostly used in the shower room.Set up.When using a partition shower room, consider how much you put things and the location when installing the rack.

2. The bathroom room is a relatively small place in our family, so the installation of the rack must save space and use the location in our space reasonably.

3. When buying the rack, you should observe whether the base of the rack is firm, especially whether there is a shaking when pushing the pull.

4. The choice of rack materials, because the bathroom has been in a humid environment for a long time, should focus on the selection of racks that are not vulnerable to moisture and rusty and rotten materials. It is recommended to use stainless steel and alloy and other racks.

5. The actual use and load -bearing capacity selected by the rack. The most fundamental of the shelf is its load -bearing ability. Generally speaking, you can see the actual storage of the residents;Essence

6. Choose a rack to match things in the bathroom. Generally speaking, it is necessary to consistent with the color tone of the three -piece bathroom set to ensure the unity of the bathroom style.