[GPS positioner tracker] How to install the installation method of automobile GPS positioner, how to install the GPS locator

The installation method of car GPS positioner

Many novices for the first contact with the GPS locator of the car, which is unknown to the installation of GPS, which has led to the disorderly installation, causing the product function to be incompletely realized, or the accuracy of the positioning is not as described as the manufacturer, which affects the wiring problem.What to do if you can't wiring.There are the most comprehensive introductions below.

1. Finding method of power cord

The electric source line is generally found in the inside of the decorative board under the steering wheel and the central electrical box wire beam. It is directly connected to the positive electrode of the battery when conditions permit.The DC voltage of the normal work of the car is 10 ~ 36V.The power cord has electricity in any state in any state.

Finding method: Pull out the key, find the thickest thicker, use the test light (or test pen) to use one end of the iron, and the other end to test on the connector of the line.If the test Lights are always bright, it means that the line is the power cord.

2. Finding method of ACC signal line

The ACC line is generally found in the inside of the decorative board under the steering wheel and the central electrical box line.The ACC signal line is the main basis for the host to determine whether the vehicle is in a starting state.

Finding method: Find a thicker line in the ignition switch line, use the test light to use the iron end to the iron, and the other end is tested on the connector of the line: when the ignition switch is hit to the "ACC" or "ON" file, the test Lights are bright;After turning off the ignition switch, the test light is destroyed. This connection is the ACC line.

3. Finding method of turning to the light line

The turning light line is generally found in the inside of the decorative board under the steering wheel, the central electrical box line beam, and the left and right front door inside line.Most models are left and right lines, but there are also very few models divided into four lines of front, rear, left, and right.

Finding method: Because the colors of the left and right Lights of small lamps, brake Lights, and reversing Lights are the same, they can be combined at the front and rear Lights to compare the color of the left and right lines to find the turning light line to see its color and size.Find the same color line.Use one end of the test light to take the iron and the other end on the line. When turning on the left or right turning light switch, use the test lamp to try this line.Light line.The other way to find the light line is the same.

Note: The turning light lines of some models (the turning light controlled by the module) cannot be confirmed on the wire beam under the switching of the turning light, and it can only be found in the same way in the central electrical box wire beam and the left and right front door beams.For models controlled by the front and rear turning Lights, it is recommended to connect the lines of the rear turning light to the line of the original car.This wiring method is settled by defense, and only the back to turn on when the defense can be turned on.

4. Finding method of the brake line

The brake line can be found at the brake light switch above the foot brake.

Finding method: Find the brake light switch, use one end of the test light to use the iron, and the other end at the switch joint.One of the lines should be constant electricity, and the other has electricity after stepping on the foot brake, and the line that has no electricity after loosening the foot brake is the brake wire.

5. Finding method of oil -breaking wires

The car oil wires are connected in the oil pump positive line.The characteristic of the positive line of the oil pump is that the ignition switch is hit to the "ON" gear. When the vehicle is not started, the line has a short period of time for 2 to 3 seconds, and then returned to the initial state of the powerless.For positive electricity.The purpose of the original car design is that before the engine starts, there is a standard oil pressure in the oil pipe, but it also prevent the ignition switch from being in the "ON" file for a long time, and the vehicle is not started to burn the oil pump.Oil pump positive lines can generally be found in the fuel tank, left or right front door beam, and central appliance box.

Finding method: Find a thicker thread in the online beam, use one end of the test light to use the iron, and the other end to test on the connector of the line.When the ignition switch is hit to the "ON" file, and the vehicle is not started, the line has a short time positive electricity for 2 to 3 seconds, and then returned to the initial state of the non -electricity;The root line is the positive polar line of the oil pump.

6. Finding method of Akmen signal line

The tailgate signal line is connected to the tail gate control switch line. This line can be found in the rear tail box, left or right front door line.Generally, vehicles have two wiring methods: positive and negative trigger.When the tailgate is turned on, the tailgate trigger line is positive electricity. When the tailgate is turned off, the tailgate trigger line is not electrical.When the tailgate is opened, the tailgate trigger line is grounded. When the tailgate is turned off, the tailgate trigger line is a positive electrical situation.

Finding method: Find the tailgate trigger line at the tailgate trigger switch, see the color and size, and then use the test light to use the iron end to the iron, and the other end is tested on the connection of the line to see if it is triggered or triggered.Then in the inside of the car, find the same color line, use one end of the test light to set up the iron, and test the line on the other end on the connector of the line.

7. Finding method of the side door signal line

The side door signal line is connected to the door control switch line.You can be found in the left and right front door beams.The original car door control switch line has two trigger methods: positive trigger and negative trigger.In addition, the original door control switch line also has two types of wiring methods: the four door control switch line connects the traditional wiring method and uses module control.Way.

Finding method: For the traditional wiring method connected to the four door control switch lines together, it can be directly connected to a single door control switch line.Look at the color and size of the door control switch line at the door control switch, and then find the same color line in the front door line.Use one end of the test light to take the iron, and the other end is tested on the connection of the line: When the side door is opened, the side door trigger line is electric. When the side door is turned off, the side door trigger line has no electricity.When the side door is opened, the side door trigger line is grounded. When the door is closed, the trigger line of the side door is a negative trigger.

For models controlled by modules, they are divided into two types of old models without original vehicle anti -theft remote control and new models with original car anti -theft remote control.The model without the original car anti -theft remote control can be connected to the control ground line connecting the indoor light to the control module.When the door is open, the indoor light is turned on by controlling the module when the door is turned on; when the door is turned off, the line is not grounded after the interior Lights are extinguished by about 20 seconds.A model with the original car anti -theft remote control should be installed with four diode (1N4001) connected to the four side door switch lines.The secondary pipe positive poles are connected to the side door signal line of the car, and the negative poles of the diode are connected to the four door control switch lines.

The voltage on the door control switching line is low. It is necessary to measure it with a multimeter and test Lights at the same time, and the results obtained are relatively clear.

8. Finding method of speaker cable

The speaker cable can be found in the inside of the panel, the central electrical box line and the horn under the steering wheel.There are four ways to connect the original car horn.

A turn off the ignition switch speaker can still be sounded, and the speaker relay controls the speaker cable (positive, negatively triggers to select one);

B The ignition switch speaker can still be rang, and the speaker relay controls the speaker ground line (negative trigger);

C can only press the ignition switch speaker to press the sound.

D can only press the ignition switch speaker, and the speaker relay controls the speaker ground wire

1. How to install the bathroom Hanging cabinet

1. Select the installation location

The bathroom cabinets are sink, so it is generally installed on the side wall of the bathroom door. Of course, when choosing a installation location, you must also choose the Hanging wall to ensure that the Hanging wall is solid. If it is a hollow wall or wall,If the body is too thin, it is not suitable to install a Hanging bathroom cabinet, otherwise the wall will be dropped and destroyed for too long after installation.

2. assembly cabinet

The assembly cabinet is very simple. Only the three -in -one screw is installed on the corresponding board and assembled the pairing plate. Then the screw is locked with a fixed screw, and the entire bathroom cabinet is installed.

3. Determine the installation height to follow up the location of the water inlet

The installation height of the cabinet and the ground is generally about 80cm ~ 85cm, and then determine the fixed holes behind the cabinet. Use the marking pen to mark it. Before the drilling is installed, the two people will hold the cabinet to compare the faucet water inlet (that is, there is no, there is no noIt is blocked by the plate), if you block it, you can use an electric drill.

4. Hanging installation cabinet

Then use the impact drill (the best rhinestone, especially the wall that has been installed with tiles) on the marked position wall surface, put the expansion Tube in the wall accessories into the hole, and then use a self -attack screw to use the self -attack screwLock with the wall.

5. Install the basin

The packet installation includes the faucet installation and the underwater pipe installation of the water washing basin. Installing the basin should use the horizontal instrument to ensure that the cabinet's level is not large, and it is necessary to distinguish the horizontal placement of the basin.

6. Install makeup mirror

Put the specifications of the back hole of the makeup mirror on the wall, install the expansion Tube, and then screw the screw into the expansion Tube to the appropriate depth, and hang the bath mirror.

2. precautions for installation of suspension bathroom cabinets

1. Please do not move and unload at will once you install it, let alone hit the mirror surface with objects to avoid breaking the injury.

2. The floor -to -ceiling bathroom mirror can be moved, but it needs to be completed by multiple people, and the angle of the placement is the same as before moving. Do not let the children get closer or push the floor mirror alone.

3. If other bathroom accessories are found to be loose, please adjust or repairs in time to avoid accidents caused by falling off.

Third, the maintenance of the Hanging bathroom counter

In order to extend the service life of the table, do not place high -temperature objects directly on the table.When placing high -temperature objects, other thermal insulation materials such as brackets and heat insulation pads with rubber feet should be added under placing objects.

1. How to design embedded closet

1. First of all, measure the size in advance, and decide how big the planned and designed closet is planned according to the size of the house area.

Unlike other furniture products, it is not directly placed, but embedded in the wall.Therefore, the problem of designing size is crucial, so that the closet can be used to get the best use and show the advantages.It is very worthy of saying that according to the advice of professionals, making embedded closets in the living room wall is a very good choice, which can make the effect of the closet to the greatest extent, and can also increase the beauty of the living room and strengthen the decorative effect.

2. Secondly, it should be designed for professionals to build professional decoration personnel.

Some people will choose to decorate themselves and build themselves. The fact is that for people who lack experience, designing closets is quite difficult, it is difficult to design beautiful and practical closets.Therefore, hiring professional designers is very helpful for designing novel, unique, and practical closet.Not only that, the price is not as expensive as people think.

(Embedded closet decoration renderings.

two,Embedded closet designstep

1. Wall cabinet: For the room (or the room of the entire wall as a wardrobe) in the structure of the structure, install a combined partition in the concave wall, and then install a closet door to become a beautiful and durable wall cabinetEssenceThe wall in the cabinet can be directly scanned with the inner wall paint or pasted with wallpaper.

2. Rail: The size of the orbital box of the upper part of the Wall cabinet should be guaranteed at 12 cm high and 9 cm wide.Like the curtain box, the rails are installed in the rail box to hang the sliding door on the track.

3. Plumb door: The golden size of the normal door is about 80 cm 200 cm. Under this structure, the door is relatively stable.If there is a height higher than 200 cm, or even higher, the sliding door is best to narrow the width of the door or make a few more sliding doors under the premise of keeping the area unchanged to keep the door stability and use safety.sex.The use of suspension sliding doors needs to be reinforced at the top. Generally, the inside of the large wooden structure sliding door also needs to be reinforced with Steel Structure, and then other production is taken outside.

[Smoking Pant] principle function function

The principle of sunshade

When it comes to sunshade, people may not feel very strange. In many people's minds, there will be "Gour Pippen" installed on the old building windows, or a canvas can be used to cover the sun on the simple iron frame. WeIt can also be called a canopy.

span & gt;The Shading can be tilted down with the small flat plane with a rolling method to use the rolling method.0~ 15The extended and recovered shade device within is an excellent sunshade product.

OblongWorking principle

The system uses the motor to drive the aluminum alloy roll Tube to rotate, so that the fabrics that wrap around the roll Tube rises,,decline.At the same time, the fabric is tightened by the springs in the arm support rod.The maximum opening angle of the system is0 ~ 130Degree can operate through various control methods such as switching, remote control, and scenery control.

OblongSystem supporting: The diameter of the roll Tube is generally used50mmor80mmWith a groove round Tube.

OblongFabric specifications: acrylic fabric (guaranteed5Non -year -old).

OblongProduct function

1The Shading canopy has a comprehensive Shading function, which can completely block the radiation of ultraviolet rays, reduce indoor temperature, and reduce air conditioning load;

2The sedan canopy has energy -saving effects, Shading canopy, which is of great significance from the perspective of energy saving and environmental protection;

3, Special UV function of the Shading cannon.

OblongProduct classification

Divided by drive: manual, electric, fixed.

OblongIt is divided into: full -box curved arms canopy, open curved arm -type sunshade, swing arm -type sunshade, sky -to -sunbone, Parasol, Parasol

The development process of the crawler arm Shading

With the development of society and the continuous improvement of people's living standards, people's living conditions have also improved greatly, and villas of various styles have also been completed.People have a private garden and private courtyard, so people have greater demand for beautiful and easy -to -use sunshade products. Various shade can also appear in the domestic market like rain.

Arms

It originated in European and American countries and has developed a history of hundreds of years.Now some economic and developed countries such as Europe and the United States are very common to use the crawling arm cannon, as popular as Chinese families using air -conditioners.It is only a matter of recent years in the Chinese market. First, some foreign brands are sold in China, and some domestic companies have also launched our own brands. This has greatly promoted the popularization of the shade.

Electric trap arm -shaped canopy

It is mainly composed of tunnels, rolls, curvatures, pimple beams, and power mechanisms. The fabrics are generally polyester and acrylic, and the roll Tube is generally aluminum roll.For the production of rolling Tube, electric sunny sheds can produce larger sunshade.The crank arm and the beam are generally aluminum alloy profiles. The power mechanism can be described as a pure electric pipe -shaped motor. It has three forms: manual Tube -shaped motor and the opening of the open -closed Shading.There is a large tensile spring in the crawling arm.Its working principle is: the Shading cloth is connected to the roller and rolled on the roll Tube, connected to the pimple beam, and the arm arm pushes the pimple beam out of the tension spring.You can realize the opening and recovery of the shade.The shade can also control the opening and closure of the shade through the remote control.

In order to make users safely and conveniently use the crawling arm -shaped canopy, some Shading companies apply some new technologies on the arm arm, such as wind, light, and rainy inductors.When the wind power, the weather device system will automatically play a role in recovering the sheets; when the sun falls, the optical sensor system will control the burnt arm of the crawler.The sunbuster is damaged by heavy rain, and the rain sensing system will automatically recover the burnt arm. The Shading has eliminated the user's worries that the user is worried about the severe weather.

The wideness of the bungalus cannon can generally achieve about 2 to 6 meters. The width of the Shading canopy is generally 1.5 meters to 3 meters. A few companies can achieve 3.5 meters or even 4 meters.Shaded scaling canopy.

The shade can not only be used for Shading during the day, but can still be used at night.After the night fell, the family or invited several friends to tast on tea and drink in the home courtyard. At this time, if the Shading canopy can create a warm and romantic atmosphere.

my country's shade canopy industry should be in a starting stage, and there is no national standard or industry standard to regulate the manufacturing and quality inspection of the Shading canopy. Relevant departments have set up the standard of the burnt arm. The unified quality standards and standard market operation mechanisms are presented in front of the world.

Electric sunny curtainHow to classify

1. According to the operation principle of the system, it can be divided into "scroll type", "folding type", "blade flip" and so on.

2. Subclassification can be divided into:

(1) FTS scroll -type ceiling curtain (electric sunshade)

(2) FSS scroll -type ceiling curtain (electric sunshade)

(3) FCS folding ceiling curtain (electric sunshade)

(4) folding the dual -track flat -moving system folding sky curtain (electric sunny curtain)

(5) Synchronous motor folding sky curtain (electric sunbath curtain)

(6) Manual/electric folding ceiling curtain (electric sunny curtain)

Method of electric sun -shaped curtain control

1. Cluster control function, cluster general control, regional division control, grading control.The above three types can also be arbitrarily combined.

2. Manual control function, manual switch control, radio remote control, manually add wireless remote control.Some products can be controlled by power -off emergency hand joystick, but only single control can be controlled.

3. Extend the control function to access the total control port of the building.Realize the intelligent control of the entire building, this is more advanced,

4. Intelligent control functions, time and space, risk control, rain control, light control, voice control, this is rarely used, it is a bit limited in operation, or the above 5 arbitrary combinations.For example, wind and rain control, scenery and rain control, and so on.

What are the functions of electric ceiling curtain

1. The improvement of electric sun -shaped curtains on Solar radiation

The insulation and insulation of the peripheral protection structure will be affected by many factors. The biggest indicator of the impact is the sunshade coefficient of the shade mechanism.The high and low shade coefficient will be controlled by the characteristics of the material and the environment.The sunshade coefficient is the ratio of Solar radiation calories generated by the feed structure with Shading measures and the feed structure without Shading measures.The smaller the sunshade coefficient, the smaller the Solar radiation calories of the outer surrounding structure, and the better the thermal insulation effect will be.For example, each of the main facing the windows that the orientation of the window that is measured in South China is: 17%west, 45%south, and 60%in the north direction.It can be seen that the effect of Shading is quite large for blocking the heat of the Solar radiation. The combination of glass curtain wall building and building Shading measures is even more obvious.

2. Electric sunshade can improve the indoor temperature effect

Shading curtains can also prevent the indoor temperature from rising to have a significant effect. Test observation in a west -towing room in South China shows that when the window is closed, there is a Shading curtain and no sunshade curtain.1.4 C.And when there is a Shading, the temperature of the room temperature is small, but the maximum value of the room temperature can be delayed accordingly, so that the indoor temperature is uniform.Therefore, sunny curtains can completely reduce cold loads for air -conditioning rooms. Therefore, the sunny curtain is one of the main and fundamental measures for electricity to save electricity for air -conditioned buildings.

3. The effect of sunny curtains on lighting

From the perspective of natural lighting, the sunshade measures will block the direct sunlight, which can prevent glare and make the indoor light illumination distribution evenly, which helps the normal and relaxed work of vision.For the surrounding environment, the sunshade can be scattered on the reflection light of the glass on the glass curtain wall (especially the coating glass), and after the sunshade, the large -scale glass reflector can cause light pollution.However, because the sunny curtain has a light -blocking effect, it will also reduce the indoor illness, which is a bit unfavorable in rainy days.Therefore, when the Shading system is designed, we must consider it, and try to meet the requirements of indoor natural lighting.

4. The role of electric sun covers on the appearance of the building

In many people, it seems that the building design of the glass curtain wall can only be flat. In fact, there are more and more designs of the sunshade facilities outside the glass top. In fact, from many foreign cases, we can find that metal glass curtain walls can be designed with light metal board design with lightweight metal board design.The beautiful Shading form is a distinctive part of the building shape.The exterior shade system of the building forms a light and shadow effect on the glass wall of the glass curtain wall, which reflects the effect of modern architectural art aesthetics.Therefore, in the European architectural industry, the outer Shading system has been designed as an active facade element as an active facade element, and it is even known as a double -layer facade form.One floor is the facade of the original building itself, and the other is the facade Shading form of a dynamic Shading state.This "dynamic" building image is not because of the fashion needs of the building facade, but a new modern architectural form produced by modern technology to solve human energy saving and enjoying natural needs.

5. The impact of sunny curtains on the ventilation of the room

The Shading facilities have a certain blocking effect on indoor ventilation. When you open the window ventilation, the indoor wind speed will weaken by 22-47%at this time, depending on the situation of the Shading facilities used.The hot air on the surface of the glass also has a blocking effect, which is not conducive to heat dissipation. Therefore, you must pay attention when choosing the structure of the sun.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is effective. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt;Correction & gt; & gt;