1. How much tiles are Solar street lights generally

The light source tile digital of Solar street lights directly affects its lighting effect. The size of Solar street lights on the market is mainly related to its height:

1. 5 meters of Solar street lights are equipped with light sources: 9 watts-18 watts.

2. 6 meters of Solar street lights are equipped with light sources: 18 watts-30 watts.

3. 7 meters of Solar street lights are equipped with light sources: 30 watts-42 watts.

4. 8 meters of Solar street lights are equipped with light sources: 42 watts -60 watts.

5, 9 meters of Solar street lights are equipped with light sources: 60 watts-80 watts.

6, 10 meters of Solar street lights are equipped with light sources: 80-100 watts.

Second, the larger the Solar street lamp, the bigger the brighter, the brighter, the

The tiles of light are the energy required for a certain amount of light. In general, the higher the tile, the brighter the light, but the greater the power it uses, but for Solar street lightsThe bigger the big one.

The light and darkness of Solar street lights is not completely determined by Watshu, but is affected by various factors such as power, lumen, and configuration. There are some Solar street lights called hundreds of watts and thousands of watts on the market. Many of them are virtual standards.Some, known as 200 watts, may be a 30 -watt lamp, because of the technology and battery technology limited by the battery board, Solar street lamps can not reach 200 watts or even 300 watts and 500 watts.

Therefore, don't blindly believe that the Solar street lights of high -watt counts. For example, Solar street lights installed in the countryside have chosen more than 30 watts earlier, and now it is basically 40 watts, 50 watts, and 60 watts.

1. What is the reason for Solar street lights

Solar street lights are energy -saving and environmentally friendly, saving costs, is a green environmental protection new street light. However, some customers also report that the Solar street lights are not on after installation. What is the reason?The reason why Solar street lights are not bright is:

1. Wiring error

In the wiring, the positive and negative pole of the lamp head will not light up. If it does not extinguish, it may be that the cockpot is reversed.

2. The capacity is too small

According to the relevant regulations, the power storage capacity of the Solar lithium battery from the factory to the transportation battery is controlled at about 30%. If it is not installed or installed for a long time, it will consume the storage electricity.After that, it will naturally not light up.

3. Quality issue

If the quality of Solar street lights is poor, it may also lead to not bright. Quality problems may exist in line failures or low power generation efficiency. In this case, you can only contact the manufacturer to return to repairs or let professionals come to the door to serve.

4. battery damage

If the damage of Solar battery battery will affect the performance of the charging and discharge, which will cause the Solar street lights to turn on the Lights shorter and Solar street lights are not bright.

5. Solar street light controller is damaged

The controller of Solar street lights regulates parameters such as Solar street light charging and voltage power. After damage, it will cause Solar street lights to discharge discharge and get out of control, which cannot be turned on.

Second, Solar street lights do not light up for the process process process

1. Check the battery, the Solar street light is not bright, it is likely to be damaged by the battery. Disassemble the battery and replace it with a new battery for inspection.That's fine; if it is still not bright, check other parts.

2. Check the Solar panel to see if it can be charged normally. It is mainly judged by watching the current on the voltage board.If there is no welding of the battery pads or no current, it needs to be replaced; if it is caused by ash, it can be cleaned up and maintained.

3. Check the controller. Similarly, remove the controller and replace the model matching controller. If it is bright normally, it means that the controller is damaged and replaced. If it is still not bright, continue the inspection.

4. Check the lamp head. If the power of the lamp head of Solar street lights is too large, it may cause the battery to over -discharge overly in advance. If the power is small, the brightness is not enough.Essence

5. If the above methods still cannot solve the problem, it may be the quality problem of Solar street lights. You need to contact the manufacturer for maintenance or replacement.

3. How to maintain and maintain Solar photovoltaic street lights

1. In the case of heavy winds, rainstorms, hail, heavy snow, etc., measures should be taken to protect Solar cells to avoid damage.

2. The lighting surface of the Solar cell should be kept clean. If there is dust or other dirt, it should be rinsed with water first, and then gently wipe the water track with clean gauze. Do not rinse it with hard objects or corrosive solvents.

3. The battery pack used to match the Solar battery Square array should be used in strict accordance with the maintenance method of the battery.

4. Check the wiring of the Solar street light electrical system regularly to avoid loosening the wiring.

5. Do not let hard or sharp objects hit the Solar panel, otherwise it will damage the Solar panel.

1. Solar street light installation method

Solar street lights have the advantages of good stability, long life, high luminous efficiency, easy installation and maintenance, high safety performance, energy saving and environmental protection, economic and practical, etc. It is widely used in the field of public power lighting. So how to install Solar street lights?

1. Pour the foundation

(1) Establish the installation location, and according to the construction drawings and the geology of the survey site, there is no shade at the top of the street light, and the lamp spacing is 40 meters as the benchmark to determine the installation location of Solar street lights.

(2) Digging road lamp foundation pit, excavate the lamp base pit in the installation location, and pay attention to confirming and protecting other facilities such as cables, pipelines and other facilities in the excavated location when digging the foundation pit.

(3) Burn the battery and build a battery box in the dug foundation pit and bury the battery box into it.

(4) Basic embedded parts of the pouring street lights, place the embedded parts of the Solar street lights into the pit, put one end of the wire Tube in the middle of the embedded parts, and the other end is placed at the buried battery.And keep the embedded parts, foundation, and ground on the same horizontal plane, and use C20 concrete to fix the embedded parts.

(5) After the construction is completed, clean up the residue on the positioning board in time. After the concrete is solidified, the Solar street lights are installed.

2. The installation method of Solar street light components

(1) Install Solar panels: Put the Solar panel on the battery plate bracket, tighten it with a screw, connect the output line of the Solar panel, pay attention to connect the positive and negative pole of the correct battery board, and use the output line of the battery plate to use it with tie the battery board.Turn it in a firm, tinten tinten on the battery panel wiring, and then put it aside to wait for the thread.

(2) Install LED lamps: Put the light line out of the light arm, leave a lamp line at one end of the installation head; support the light pole and wear the other end of the light line from the slide hole reserved by the light rod.Out, install the light line to one end of the top of the light pole; install the lamp head at the other end of the light line, align the screw holes on the light arm and the light rod, and then tighten the light arm with a quickly wrench;Put on the top of the top of the light rod to make a mark. Together with the Solar panel thread wiring, put the two wires together on the bottom of the light rod with a thin thread Tube, and fix the Solar panel on the light rod.

(3) Lantern rod Hanging: After checking the fixed conditions of each component, put the sling rope in the appropriate position of the light rod, slowly roll up the lamps, and when the light rod is lifted to the front of the base, slowly put down the light pole and rotate the light pole at the same time.Adjust the lamp head to the pavement, and the holes on the flange plate are aimed at the foot bolts; after the flange plate falls on the foundation, put the flat pad, spring pad, and nuts in turn, and tighten the nut with a wrench to fix the light pole.

(4) Install the battery and controller: Put the battery in the battery shaft and put the battery thread on the road base with fine iron; then connect the connection line to the controller, first connect to the battery, then the load, and then connect to the Solar board; debugging; debugging;Whether the street light work is normal. If it is normal, set the controller mode to make the street light light up. If there is no problem, you can seal the lamp cover of the light rod.

3. Component adjustment and secondary embedding

After the installation of Solar street lights is completed, check the installation effect of the overall street lights, re -adjust the light rods, and check whether the rising angle of the battery board is deviated, whether the light head is legitimate, etc.;The base is embedded in a secondary embedding, and the base of the light rod is made into a small Square with a cement to make the Solar street light more firm and reliable.

2. What should you pay attention to when installing Solar lighting street lights

Solar lighting street lights can save energy and relieve energy consumption. It is a very practical type of new street lights. However, when installing Solar street lights, you should also pay attention to some aspects, such as:

1. installation location

Try to avoid installation in the low -lying road sections of the road. Pay attention to whether the installation location is to fill the soil when pouring. If it is backfill, the basic pit should be deepened and increased, so as to ensure the stability of the later use of Solar street lights.

2. installation time

The installation of Solar street lights should be installed on a sunny day. If it is installed on a rainy day, it will not be able to meet the design requirements after the light consumes power and does not charge it. Also, try not to light up the Lights on the day of the installation.After the electricity, the load is connected in the evening.

3. The angle of the battery board

The brackets of Solar panels are generally made before the factory. As long as you ensure that you can facing the south and ensure that there is no obscuration around, if the deviation is large, you may need to be adjusted.

4. Pay attention to wiring

Solar street lights are low -voltage systems. When wiring, it is mainly to distinguish between positive and negative electrodes. After determining the positive and negative electrode of the battery plate, light source, and battery, it is necessary to strictly follow the wiring description of the controller.

1. What battery is used for Solar street lights

Solar street lights are environmentally friendly street lights that use solar energy to power on street lights. Generally, solar energy is a crystalline silicon Solar cell power supply. The battery stores electrical energy. There are four commonly used batteries:

1. Lead -acid battery

The pole plate of the lead -acid battery is composed of lead and lead, and the electrolyte is a hydraulic solution of sulfuric acid.Its main advantage is that the voltage is stable and the price is cheap; the disadvantage is that it is lower than energy (that is, electrical energy stored per kilogram of battery), so the volume is relatively large, the service life is about 300-500 deep cycles, and the daily maintenance is frequent.The industry is still used in large quantities.

2. Collagen battery

Collagen battery is actually a upgraded maintenance version of lead -acid batteries. It is replaced with colloidal electrolytes to replace sulfate electrolytes. It has improved in terms of safety, power storage capacity, discharge performance and service life.Some are even higher than the ternary lithium battery.It can be used within the temperature range of -40 C-65 C, especially the low temperature performance is good, suitable for high-cold regions in the north.Seismic resistance is good and can be used safely in various harsh environments.The service life is about doubled than the ordinary lead -acid battery.

3. Tricss lithium battery

Higher, small, fast charging, high price.The number of deep cycles of ternary lithium batteries is about 500-800 times, and the life span is about 1 times longer than the lead-acid battery, and the temperature range is -15 C -45 C.However, the disadvantage is that it is not stable. The ternary lithium battery of the unqualified manufacturer may explode or fire when the temperature is over -charging or the temperature is too high.

4. Lithium iron phosphate battery

Higher, small, fast charging, long service life, good stability, and of course the highest price.The number of deep-loop charging is about 1500-2000 times, and the service life is long, which can generally reach 8-10 years. The stability is strong, the use temperature range is wide, and it can be used at -40 C-70 C.

2. How much is the battery of Solar street lights

The battery voltage of Solar street lights is generally between 12 volts and 24 volts, and it is a DC voltage.The related component configuration of Solar street lights is:

1. 24VLED: Choose LED lighting, LED lights have long service life, soft light, and reasonable price. It can be adjusted during the scarce time of night pedestrians, which is conducive to power saving, which can reduce the configuration of the battery board and save costs.About 80-105LM per tile, light failure is less than year 5%.

2, 12V battery (string 24V): Choose lead acid to maintain the battery, moderate price and stable performance.

3. 12V battery board (string 24V): The conversion rate is more than 15%single crystal positive film.

4, 24V controller: MCT charging method, briefing function.

1. What are the lamps of high rod lamps

High rod lamps generally refer to a new type of lighting device composed of steel tapered light rods and high -power combined light racks above 15 meters. It consists of lamp head, internal lamp electrical, rod body and basic part.Mi is suitable for the use of urban squares, stations, docks, cargo farms, highways, stadiums, overpass and other places.

Second, high rod light installation construction plan

1. Organization of basic buried parts

Clear the garbage and miscellaneous objects on the basic surface of the concrete, remove the protective objects wrapped on the embedded object bolts, review the spacing size (including diagonal sizes) between each bolt, and confirm that the size of the bolt position is consistent with the icon size. The nut can be freely free.Twisted.

2. Package of the rod body

Before starting, a fine steel wire or iron wire with a high length should be penetrated into the rod body from the electrical door. It is used to guide the wire rope and cable in the future.

3. Wear steel rope and cable

After the rod body socket is completed, connect the cable connector with the main steel wire rope of the rolling machine, and then fix it with the guidance iron wire reserved in the pole body in the electrical door, loosen the rolling machine, so that the main steel wire rope is released from the rolling cylinder.At the same time, the tensor is tilted to guide the wire at the other end of the rod body, pulling the ride connector out of the small ends of the rod body, so that the riggle connector will be retracted and entering the rod body.

4. Head installation

The front end of the pole body that has been completed and penetrated by the wire rope and cable is matched with objects (the electrical door of the pole body is up).Cover, lightning rod and connect to the connection line.

5. Hanging

According to their respective situations of 35 meters, 15 meters, and 8 -meter steel rods, they choose cranes and cranes.During the lifting process, the person in charge was commanded uniformly to ensure that the whole process of the light rod Hanging was safely and orderly.

6. installation and debugging of the lamplet

Twist the bolt on the nut of the lamp plate Sleeve, hang up the lamp plate with a crane, and put it in the front end of the light rod.Turn the bolt tightly in turn, and adjust the bolt into the depth, so that the lantern Sleeve sleeve and the surrounding space of the rod body are basically consistent.

7. lighting installation

Install the lamps at the predetermined position of the lamp plate, wiring, and send the power supply, and perform a 24 -hour test.

3. precautions for the installation of road high rod Lights

1. During installation, high -rod Lights should be used reasonably to ensure that the distribution of the light on the ground is evenly distributed. At the same time, according to the width of the road, the light control control of the past vehicles and pedestrian conditions must be performed.

2. When installing, install a suitable length of each stitching.During the installation process, it is easy to cause a certain error. In order to be convenient and fast, it is necessary to apply suitable forces at both ends to obtain a close socket.

3. The installation of high rod Lights should pay attention to the reasonable light, and choose a relatively high -quality product in performance.

4. After the installation of high rod Lights is completed, it is necessary to check it to test whether the power supply can work normally, whether the screw installation is in place, and whether there is a loose.

In general, high rod Lights are large lamps. The first thing to ensure is its safety performance. Therefore, installing high rod street lights must not be sloppy to avoid safety accidents.

Disclaimer: The above method stems from the index of the program system or the sharing of netizens. It is for your reference only and does not represent the research perspective of this website. It proves that it is effective. Please pay attention to the authenticity and authority of the source of the content of the content.Apply to delete & gt; & gt;Correction & gt; & gt;