Special Mic How to build artificial grass on the paving skills and tricks of artificial lawn
1. How to build artificial grass in the football field
1 Before entering the construction, the flatness, slope, and surface perception of the foundation are detected. The amendment measures and requirements are required. After meeting the requirements, we can enter the construction.
2 , Put the line (measurement), find out the center point of the venue and two semi -circular hearts, and put the ruler lines according to these three positioning points, set the midline of the venue and the side line, and then determine the various corners of the venue on the venue.The accurate position of the line, then set the position of each function point and line ,, And pop up with ink or paint lines.
3 2. Spread the turf into the venue along the horizontal side direction, and push from one end of the vertical side to the other end. When spreading, try to make the white paddling line woven on the grass on the function line to reduce the number of cutting.
4 , Cut the white grass threads that are woven on the outside of the turf and fail to place them on the function line position, and place it aside. If the white scratch line is woven, it must be hand -cut into the corresponding function line width of the site.line.
5 , Overlap the seams of green garries 1cm , Cut with a grass -cutting knife from the center of the connection, so that the turf on both sides is compact as possible, and then trimmed with a paper knife.
6 2. Roll the bottom of the garries at the seam, and turn the width of the grass on each side. 50 Cm, then will 25 The centimeter -wide connection Belt is rolled along the center of the seam of the grass, and the special glue is painted on the bottom and connecting band of the coats of the garries. 6 centimeter.The connection band is evenly scraped on the connection band with a rubber scraper.In order to achieve the best bonding effect, the rubber fluid is fully stirred or poured several times before using it to mix the rubber liquid evenly.When applying brushes, apply glue in the same direction, which is conducive to driving out the air and increasing the uniformity of glue and enhancing the adhesion.Release: After the glue is applied, the glue is volatile naturally. After the glue is applied, it must be dried for a period of time. The solvent is volatilized to prevent the glue layer from sticking to or producing bubbles, which affects the quality of bonding.The drying time should not be too long, so as not to lose stickiness and produce off -gum.Waiting for the rubber layer to be dry membrane (about 5-25 minute) /25 can be bonded.Adhesive: When bonding, the turf on both sides should be aligned with the adhesion on the connection zone at one time, and need to be compressed to make the bonding part tightly. Do not move back and forth to avoid affecting the bonding effect.If the turf or connection is humid, it is necessary to dry the dryness of the angel.
7 After the basic stitching of the turf, pull out the accurate positions of each functional line and point again, cut it with a paper knife, draw the cut straw, put the connection Belt, scrape glue, and prepare the original preparation.Put the white grass thread back. After the glue is knotted, repeatedly be beaten with a rubber hammer to make the connection part tightly.
8 After the artificial grass leather paving is stitched, the folding part of the turf needs to be opened with a paper knife, straightened the docking, removed the overlap, and then tied.
9 After all the garries are bonded, the brush machine is combed with a brushing machine.The first time the brush machine was combed with the pouring grass thread of the audience.
10 ,according to 4M*4M Put the specifications of the audience. Pour the quartz sand evenly per Square meter of sand in different meters of sand in the specifications.Sort out once.
11 After the filling is completed, the grass fiber is combed with the grass fiber once.
12 2. After the work is completed, inspect and clear the field in accordance with the quality requirements of the artificial grass surface layer, and rectify the unqualified places.
2. Playing skills and tricks of Artificial lawn
1 After the Artificial lawn arrives, don't rush to cut, spread all the lawns, at least dry and put it twenty four In hours, the stress generated in the production and transportation of Artificial lawn was completely released, and the lawn adapted to the heat expansion and contraction of the new environment, so as not to be too large after the paving.
2 When cutting artificial lawns, do not pursue a knife tailor. It is best to cut a little bit, and then a little bit of the side and repair, so as not to be too large.Only slow work can work out.
3 When cutting artificial lawns, turn the lawn up, cutting from the back of the back will be easier.
4 When brushing the glue, be careful not to apply the glue to the grass, otherwise the seams will be more obvious.
5 There is no need to brush glue between the seam band and the cement floor. While saving the glue, the suspended state of the lawn is conducive to the displacement caused by the drainage and the thermal expansion and contraction in the use of water.
6 When cutting, it is necessary to ensure that the turf of the entire venue is consistent, otherwise there will be obvious color difference.